Part |
Picture |
Description |
RB3-0010-030CN |
Feed plate - Center metal plate with slots that the ribs on the middle frame assembly go through |
RB3-0011-000CN |
Feed drive shaft - Long shaft with eight feed belt ball type pulleys and one ribbed feed guide drive belt pulley |
RB3-0012-000CN |
Belt roller - Small oval shaped roller approximately 1-3/4 inches long |
RB3-0014-000CN |
Bushing assembly (black plastic bushing with small guide roller on top) |
RB3-0015-000CN |
Compression spring |
RB3-0016-000CN |
Electrical contact spring - Spring steel wire with compression springs formed on both ends |
RB3-0019-000CN |
Toner catch tray (curved Black plastic piece) - Holds residual toner from photosensitive drum |
RB3-0022-000CN |
22 tooth gear (Black plastic) - Small gear with diagonally cut teeth |
RB3-0023-000CN |
Interlock switch holder (Quartz Gray plastic) - Does NOT include the micro-switch |
RB3-0025-000CN |
Airflow guide (duct) / fan holder bracket assembly (Quartz Gray plastic) |
RB3-0028-000CN |
Left side cover (Quartz Gray) - Does not include any attaching parts |
RB3-0030-000CN |
Upper rear cover (Quartz Gray) - Mounts on the upper rear of the printer above the face-up output tray door |
RB3-0032-000CN |
Face-down paper output L-Shaped cover ( Blue) - Serves as the rear of the tray for the face-down output tray on top of the printer |
RB3-0033-000CN |
Memory access door (Quartz Gray perforated plastic) - Allows access to the printer memory slots - Mounts on the right side cover |
RB3-0035-000CN |
Interface bezel (Quartz Gray plastic) - Vertical cover that surronds the interface connectors |
RB3-0037-000CN |
Power switch rod - Goes between the power button and the power switch on the low voltage power supply board |
RB3-0042-000CN |
Electrical contact spring |
RB3-0043-000CN |
Electrical contact spring |
RB3-0044-000CN |
Electrical contact spring |
RB3-0045-000CN |
Electrical contact spring |
RB3-0046-000CN |
Electrical contact spring |
RB3-0047-000CN |
Electrical contact spring |
RB3-0048-000CN |
Electrical contact spring |
RB3-0052-000CN |
Gear Cover (Small Black plastic cover) - Covers the left end of the feed drive shaft |
RB3-0056-000CN |
Insulating sheet (Transparent plastic) |
RB3-0057-000CN |
Transfer slide plate - Small U shaped metal insert plates |
RB3-0060-020CN |
Idler gear shaft - Short metal rod |
RB3-0061-000CN |
Pulley roller (accommodates three feed belts) - Small black roller approximately 3.49cm (1-3/4 inches) long with three ball type pulleys |
RB3-0062-000CN |
PC board support (Black plastic holder) |
RB3-0063-000CN |
Paper feed belt - Small black rubber belt approximately 1/8 inch wide with little A shaped ribs on it |
RB3-0065-000CN |
Contact plate - copper clad metal spring - Holds the left end of the small 500 Meg-ohm resistor |
RB3-0066-000CN |
Contact plate - copper clad metal spring - Holds the right end of the small 500 Meg-ohm resistor |
RB3-0067-000CN |
Pulley roller (accommodates one feed belt) - Small black roller approximately 1.59cm (5/8 inch) long with one ball type pulley |
RB3-0089-000CN |
Top cover rack arm (Black) - Plastic arm with teeth on bottom edge - Disengages the imaging drum/transfer assembly drive cams when the top door is open |
RB3-0089-030CN |
Top cover rack arm (Black) - Plastic arm with teeth on bottom edge - Disengages the imaging drum/transfer assembly drive cams when the top door is open |
RB3-0090-000CN |
Rack slide - White plastic piece with gear teeth layed out in rack form on both sides |
RB3-0091-000CN |
16 tooth gear (Black plastic) - Gear with large stop tooth and shaft lock tab |
RB3-0092-000CN |
15 tooth gear with drive shaft (Black plastic) |
RB3-0102-000CN |
Front inner cover (Blue) - Mounts on the front frame above the multi-purpose input tray |
RB3-0103-000CN |
Front lower cover (blue plastic) - Front lower strip below the multi-purpose input tray - Has recessed area for the printer logo |
RB3-0104-000CN |
Roller cover - Covers the multipurpose paper pickup roller assembly - Mounts on the lower front of the front frame assembly |
RB3-0105-020CN |
Center support frame (black plastic) - Support structure for the paper pickup roller, feed roller, and paper sensors |
RB3-0106-000CN |
Left side frame/cover (Quartz Gray) plastic - Left side cover and input paper tray guide |
RB3-0108-000CN |
Metal support cross-brace - Mounts on the top rear of the left and right support frame/cover assemblies |
RB3-0108-020CN |
Metal support cross-brace - Mounts on the top rear of the left and right support frame/cover assemblies - For the base on the 250-sheet input tray assembly |
RB3-0109-000CN |
Front cover for the 250 sheet paper cassette tray (Blue) plastic - Has molded in paper loading instructions and a '2' on the front |
RB3-0111-000CN |
Paper flag - Plastic rod with paper sensing flag on one end and sensor activator flag on the other |
RB3-0119-000CN |
Grounding plate |
RB3-0120-000CN |
Solenoid cover (Steel) - For magnetic wave sheilding |
RB3-0120-020CN |
Solenoid cover (Steel) - For magnetic wave sheilding - Mounts over the solenoid on the right side of the front frame assembly |
RB3-0121-000CN |
Right retaining spring - Helps to secure and ground the imaging drum/transfer assembly in the printer |
RB3-0122-000CN |
Left retaining spring - Helps to secure the imaging drum/transfer assembly in the printer |
RB3-0129-000CN |
Feed roller assembly - Includes the metal shaft and two small rubber rollers |
RB3-0129-020CN |
Feed roller assembly - Includes the metal shaft and two small rubber rollers - Feeds paper from the paper cassette (or tray three below) into the printer - Mounts on the top of the center frame in the base on the 250-sheet input tray assembly |
RB3-0130-000CN |
Shaft mounted sensor flag (black plastic) |
RB3-0132-000CN |
Mechanical sensor flag (black plastic) |
RB3-0135-000CN |
Test print flag (Black lever) |
RB3-0136-020CN |
Solenoid cover/magnetic shield |
RB3-0137-000CN |
Grounding plate |
RB3-0140-000CN |
Left cover plate (Quartz Gray) plastic - Mounts on the left side of the center frame assembly |
RB3-0141-000CN |
Right cover plate (Quartz Gray) plastic - Mounts on the right side of the center frame assembly |
RB3-0160-000CN |
Paper pickup roller ('D' shaped) |
RB3-0161-000CN |
Paper pickup roller assembly - Includes the D shaped rubber roller on a plastic shaft |
RB3-0165-000CN |
Top inner cover (black plastic) - Covers the back half of the pressure roller arms and springs |
RB3-0166-000CN |
Bottom inner cover (Black) plastic - One covers the paper feed sensor in the center and the other covers sensor wires toward the right side |
RB3-0176-000CN |
Face-Up output tray door (ONLY) |
RB3-0178-000CN |
Right side lock release lever |
RB3-0179-000CN |
Left side lock release lever |
RB3-0180-000CN |
Paper inlet guide - Small ribbed plastic piece |
RB3-0282-000CN |
Inner cover - Covers the small interconnecting PC board |
RB3-0283-000CN |
Inner cover - Covers the bottom of the connector that interconnects the input tray base to the printer |
RB3-0286-000CN |
Contact plate for HP Color LaserJet 2500 Seriess |
RB3-0287-000CN |
Front cover for HP Color LaserJet 9500 Series |
RB3-0289-000CN |
Cover left for HP Color LaserJet 9500 Series |
RB3-0304-040CN |
Front swivel caster - Mounts on the bottom frame of the 2,000-sheet paper feeder assembly (two used) |
RB3-0304-050CN |
Front swivel caster - Mounts on the bottom frame of the 2,000-sheet paper feeder assembly (two used) |
RB3-0607-000CN |
Air filter at top rear of printer - Formatter fan air filter |
RB3-0978-020CN |
Mounting bracket - Bracket that secures the 2 X 500 sheet feeder/tray assembly to printer - Located on top left rear of feeder/tray assembly |
RB3-0979-020CN |
Mounting bracket - Bracket that secures the 2 X 500 sheet feeder/tray assembly to printer - Located on top right rear of feeder/tray assembly |
RB3-1024-000CN |
Pressure plate - Small steel channel shaped plate |
RB3-1025-000CN |
Compression spring |
RB3-1026-000CN |
Bushing - Plastic U shaped bushing |
RB3-1027-000CN |
Bushing - Flanged plastic bushing |
RB3-1029-000CN |
Gear holder - Hollow tube with locking tab |
RB3-1032-000CN |
Fuser Assembly upper cover - Ribbed cover with end caps |
RB3-1034-000CN |
Pressure roller assembly - Hard rubber roller on a metal drive shaft |
RB3-1065-000CN |
Torsion spring for HP Color LaserJet 2820 Series |
RB3-1083-000CN |
Face-down paper exit arm - Helps to prevent paper re-entering the printer and paper curl |
RB3-1087-000CN |
Top cover for HP Color LaserJet 2820 Series |
RB3-1088-000CN |
Transfer inlet guide assembly - Angled metal guide between the registration roller and the transfer roller |
RB3-1094-000CN |
Bushing assembly (Black plastic bushing with small guide roller on top) |
RB3-1108-000CN |
Front inner cover (Graphite Black plastic) - Mounts on the front frame above the multi-purpose input tray |
RB3-1110-000CN |
Insulating sheet (Transparent plastic) - For the power supply base assembly |
RB3-1112-000CN |
Interface bezel (Alloy Gray plastic) - Vertical cover that surronds the interface connectors |
RB3-1113-000CN |
Grounding plate - Small plate with grounding finger |
RB3-1123-000CN |
Top cover (ONLY) - Has molded-in tray for face down paper output - Does NOT include lift-up door or any other attaching parts |
RB3-1125-000CN |
Upper front cover - Rectangular plastic piece with recess for the printer logo |
RB3-1126-000CN |
Upper left cover - Small cover that is part of the inner side wall in the cartridge access area and provides support for the exterior left side cover |
RB3-1128-000CN |
Left side cover (ONLY) - Does NOT include the vent cover or power switch button |
RB3-1129-000CN |
Right side cover (ONLY) - Does NOT include the memory access door or grounding plate |
RB3-1130-000CN |
Upper rear cover assembly - Also guides the paper from the Fuser Assembly to the top output (face down) tray |
RB3-1131-000CN |
Left rear cover - U shaped cover that mounts on the under-side of the extension for the left scanner hinge |
RB3-1132-000CN |
Right rear cover - U shaped cover that mounts on the under-side of the extension for the right scanner hinge - Covers the scanner interconnection cables |
RB3-1133-000CN |
Upper front cover (ONLY) - Back support for the multipurpose cover assembly |
RB3-1134-000CN |
Internal cover (ONLY) - Curved plastic piece with recessed area for grasping the handle on the imaging drum/transfer assembly - Mounts towards the front of the printer just above the multipurpose tray |
RB3-1135-000CN |
Lower front cover - Rectangular plastic strip - Mounts just below the multipurpose input tray on the front of the printer |
RB3-1136-000CN |
Face-down paper output cover (L shaped plastic) - Serves as the rear of the tray for the face-down output on top of the printer |
RB3-1137-000CN |
I/O cover - Rectangular plastic cover with a recessed cutout for the interface connectors |
RB3-1138-000CN |
Memory access door - Provides access for changing or adding DIMM memory modules to the printer |
RB3-1139-000CN |
Vent cover - Rectangular plastic cover with molded-in ventilation louvers |
RB3-1140-000CN |
Rear cover / face-up output tray (ONLY) - When opened, routes printed pages to this cover/tray for face-up output |