Part |
Picture |
Description |
RB3-1140-000CN |
Rear cover / face-up output tray (ONLY) - When opened, routes printed pages to this cover/tray for face-up output |
RB3-1140-010CN |
Rear cover / face-up output tray - When opened, routes printed pages to this cover/tray for face-up output |
RB3-1145-000CN |
Power switch rod - Goes between the power button and the power switch on the low voltage power supply board |
RB3-1146-000CN |
Mount retainer - Holds the spring loaded power switch rod on the left side cover |
RB3-1147-000CN |
Rear foot - Helps in printer stability when the scanner has been lifted up - Also forms a recess for the alignment peg on the optional paper tray |
RB3-1150-000CN |
Grounding spring |
RB3-1154-000CN |
Left link mount - Rectangular plastic piece that has a recess for the printer-to-scanner link and includes the bottom half of the scanner hinge |
RB3-1158-000CN |
Right link mount - L shaped plastic piece that has a recess for the printer-to-scanner link and includes the bottom half of the scanner hinge |
RB3-1166-000CN |
Right pressure release lever - To release pressure between the pressure roller and the heater assembly to clear paper jams |
RB3-1167-000CN |
Left pressure release lever - To release pressure between the pressure roller and the heater assembly to clear paper jams |
RB3-1168-000CN |
Left side support frame/cover assembly - For the base on the 250-sheet input tray assembly |
RB3-1170-000CN |
Front cover - Mounts on the front of the cassette assembly for the 250-sheet input tray assembly |
RB3-1292-020CN |
Fixing Power SUPPLY COVER |
RB3-1305-000CN |
Control panel overlay label - (English) |
RB3-1379-000CN |
Insulator sheet - L shaped plastic insulator sheet - Protects the camera (photo) memory interface assembly from shorting against the support bracket |
RB9-0834-000CN |
Shaft bushing/retainer - Right side pickup roller support bushing |
RB9-0835-000CN |
Shaft bushing/retainer - Left side pickup roller support bushing |
RB9-0843-000CN |
Torsion spring - Provides a small amount of back pressure for the paper sensor flag |
RB9-0879-000CN |
Bushing/shaft retainer assembly (Black plastic) |
RB9-0880-000CN |
Upper rear cover (Alloy Gray plastic) |
RB9-0881-000CN |
Face-down paper output cover (L-Shaped Graphite Black plastic) - Serves as the rear of the tray for the face-down output tray on top of the printer |
RB9-0884-000CN |
DIMM memory door (Alloy Gray perforated plastic) - Access door for adding or removing printer memory or font DIMM |
RB9-0886-000CN |
Left side cover ONLY (Alloy Gray plastic) - Does not include any attaching parts |
RB9-0889-000CN |
Tray hinge - L shaped plastic arm - For the left side of the multi-purpose front input tray (tray 1) |
RB9-0890-000CN |
Tray hinge - L shaped plastic arm - For the right side of the multipurpose front input tray (tray 1) |
RB9-0897-000CN |
Front lower cover (Graphite Black plastic) - Front lower strip below the multipurpose input tray - Has recessed area for the printer logo |
RB9-0901-000CN |
Airflow guide (duct) / fan holder bracket assembly (Alloy Gray plastic) |
RC1-0198-000CN |
Tension spring - Provides tension for lifter drive assembly |
RC1-0503-000CN |
Paper size detect lever for Tray 2 - Also used in optional trays 3 and 4 - Three used per tray - One each |
RC1-0808-020CN |
Fixed height caster assembly |
RC1-0821-000CN |
Top rear cover - Slightly curved plastic piece - Mounts just behind the paper loading access door |
RC1-0822-000CN |
Left cover - Large rectangular cover held in place with four screws - Mounts on the printer side of the high capacity input tray |
RC1-0822-020CN |
Left cover - Large rectangular cover held in place with four screws - Mounts on the printer side of the high capacity input tray |
RC1-0823-000CN |
Left front cover - Narrow rectangular cover - Mounts on the printer side of the high capacity input tray |
RC1-0825-000CN |
Right cover - Narrow rectangular cover - Mounts next to the pull-down paper access door |
RC1-0826-000CN |
Lower right cover - Trim piece below the pull-down paper loading access door |
RC1-0827-000CN |
Rear cover - Large rectangular cover held in place with four screws - Mounts next to where the power and interface cables exit the high capacity input tray |
RC1-0884-000CN |
Cam cover - Covers the (right) door sensing arm - Mounts on the inside rear side wall of the paper tray assembly |
RC1-0939-000CN |
Separation pad assembly for the Tray 1 position and fits in a holder that sits just below the Tray 1 paper pickup roller. |
RC1-0954-000CN |
Separation pad assembly in front portion of 250 sheet tray |
RC1-1036-000CN |
Separation pad support - Pivoting L shaped metal support frame (Does NOT include the separation pad assembly) |
RC1-1038-000CN |
Tray 1/MP Tray damper - Dampens movement on right side of drop down Tray 1 - White plastic gear mounted on a black plastic arm |
RC1-1049-000CN |
Sensor holder - Mount for toner hopper full sensor (PS13) and associated lens |
RC1-1050-000CN |
Lens - Optical lens used with toner hopper full (PS13) sensor - Two used |
RC1-1148-000CN |
Right side swing lock - Black plastic swing guide arm lever |
RC1-1149-000CN |
Tension spring - Provides tension for right side swing lock |
RC1-1151-000CN |
Contact plate - Grounding plate on left side for Yellow toner cartridge |
RC1-1152-000CN |
Contact plate - Grounding plate on left side for Black toner cartridge |
RC1-1153-000CN |
Contact plate - Grounding plate on left side for Cyan toner cartridge |
RC1-1155-000CN |
Contact plate - Grounding plate on left side for Magenta toner cartridge |
RC1-1156-000CN |
Left guide rod - Front inside portion of white plastic swing guide rod assembly |
RC1-1158-000CN |
Left front cover rod support - Attaches above front cover hinge - Attachment point for toner cartridge disengagment rod on left side |
RC1-1159-000CN |
Right front cover rod support - Attaches above front cover hinge on right side - Attachment point for belt drive disengagement rod on right side |
RC1-1169-000CN |
Left drum lock arm - Black plastic drum lock arm for Cyan cartridge |
RC1-1170-000CN |
Left drum lock arm - Black plastic drum lock arm for black toner cartridge |
RC1-1175-000CN |
Interlock switch arm - Located at top right corner of printer frame |
RC1-1176-000CN |
Interlock switch lever - Lever that activates front door switch SW1 - Connected to left side of front door release handle square shaft |
RC1-1177-000CN |
Grounding spring - Ground spring located on left guide rod assembly |
RC1-1181-000CN |
Cable guide - Located in front of DC Controller board |
RC1-1184-000CN |
Tension spring - Provides tension for top left drum lock arm |
RC1-1185-000CN |
Tension spring - Provides tension for black plastic drum lock arms |
RC1-1186-000CN |
Clutch mount - Registration clutch (CL1) mount plate |
RC1-1213-000CN |
Cluster gear - 86-tooth/23-tooth gear - Mounted in gear assembly on right rear side of printer |
RC1-1218-000CN |
Gear bushing - White plastic bushing for 29 tooth gears on front right inside mounting plate - Four used |
RC1-1224-000CN |
Cluster gear - 50 tooth/90 tooth gear mounted in gear assembly on right side of printer |
RC1-1229-000CN |
Cluster gear - 90-tooth/28-tooth gear - Mounted in gear assembly on right rear side of printer |
RC1-1230-000CN |
74 tooth gear - Black plastic 74 tooth gear mounted in gear assembly on right side of printer - Four used |
RC1-1231-000CN |
59 tooth gear - 59 tooth gear mounted in gear assembly on right side of printer - Two used |
RC1-1233-000CN |
69 tooth gear - 69 tooth gear mounted in gear assembly on right side of printer |
RC1-1234-000CN |
29 tooth gear - White plastic toner drive gear mounted in gear assembly on right side of printer - Four used |
RC1-1242-000CN |
Gear reinforcement plate - Mounting plate for 29-tooth gears on front right inside mounting plate - Four used |
RC1-1243-000CN |
Bushing - White plastic gear bushing |
RC1-1244-000CN |
Bushing - Four bushings used on outside drive plate - One each |
RC1-1246-000CN |
Right drum lock arm - Right side lock arm for Yellow toner cartridge |
RC1-1247-000CN |
ITB coupling lever - Connected to right side of front door release handle square shaft |
RC1-1248-000CN |
Intermediate Transfer Belt (ITB) coupling lever - White plastic lever with eight gear teeth |
RC1-1252-000CN |
Cluster gear - 120 tooth/17 tooth - Large gear in developer disengaging drive assembly |
RC1-1259-000CN |
Tension spring - Provides tension for right drum lock arm - Four used |
RC1-1260-000CN |
Tension spring - Provides tension for ITB (Image Transfer Belt) coupler at top right front of printer frame |
RC1-1277-000CN |
Metal gear mounting plate - Vertical piece the supports gear assembly on outside of right side printer frame |
RC1-1280-Right_Side_Plate |
Black molding with 3 screws and circular end. items sits on the Right Side Plate Assembly (4 used on printer). Part installs infront of Developing motor gears. |
RC1-1281-000CN |
39 tooth gear - 39 tooth gear mounted in gear assembly on right side of printer |
RC1-1283-000CN |
Cluster gear - 26 tooth/47 tooth gear mounted in gear assembly on right side of printer |
RC1-1284-000CN |
Cluster gear - 31 tooth/19 tooth gear mounted in gear assembly on right side of printer |
RC1-1286-000CN |
Cluster gear - 45 tooth/25 tooth gear mounted in gear assembly on right side of printer |
RC1-1287-000CN |
Gear holder - Pivot gear holder for 104/25 cluster gear and |
RC1-1288-000CN |
38 tooth gear - 38 tooth gear mounted in gear assembly on right side of printer |
RC1-1291-000CN |
Cluster gear - 104 tooth/25 tooth gear mounted in gear assembly on right side of printer |
RC1-1292-000CN |
Tension spring - Provides tension for gear holder that holds 104/25 tooth cluster gear |
RC1-1294-000CN |
43 tooth gear - 43 tooth gear mounted in gear assembly on right side of printer |
RC1-1295-000CN |
27 tooth gear - 27 tooth gear mounted in gear assembly on right side of printer |
RC1-1298-000CN |
Cluster gear - 26 tooth/22 tooth/20 tooth gear mounted in gear assembly on right side of printer |
RC1-1300-000CN |
Cluster gear - 54 tooth/17 tooth gear mounted in gear assembly on right side of printer |
RC1-1302-000CN |
79 tooth gear - Large gear mounted in gear assembly on right side of printer |
RC1-1306-000CN |
Cable guide - Cable guide on right side of 250 sheet/Tray 2 frame |
RC1-1310-000CN |
Bushing - White plastic gear bushing |
RC1-1328-000CN |
Torsion spring - Provides tension for sensor flag in center frame assembly |
RC1-1329-000CN |
Sensor holder - Holder for developing engaging sensor PS14 |
RC1-1330-000CN |
Sensor flag - Flag that activates sensor PS14 |
RC1-1342-000CN |
Wire harness guide - Protects wire harness that goes through lower right front corner of printer |
RC1-1343-000CN |
PC board holder - Small plastic holder for memory controller PC board assembly |
RC1-1345-000CN |
Upper left rear air duct - Housing for exhaust fan FM1 |
RC1-1347-000CN |
Power switch rod - Mechanical link between power switch on front of printer and DC controller board |
RC1-1348-000CN |
DC controller board mounting plate |
RC1-1349-000CN |
Shield plate - Metal plate that covers memory controller board |
RC1-1350-000CN |
Upper left rear fan duct to printer frame mount |
RC1-1353-000CN |
Motor cover - Black plastic cover for feed motor M1 |
RC1-1354-000CN |
Air duct - Plastic air duct below laser scanner assembly |
RC1-1355-000CN |
Mounting plate - |
RC1-1361-000CN |
Right lock arm - Locks the developing drum |
RC1-1362-000CN |
Right drum lock arm - Right side lock arm for Cyan toner cartridge |