| Part |
Picture |
Description |
| Q6665-60020 |
HEATER RELAY ASSEMBLY - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60021 |
FIRMWARE ACCESS COVER - LOCATED ON TOP OF THE ELECTRONICS MODULE COVER - FOR DESIGNJET 9000S PRINTER SERIES |
| Q6665-60022 |
ELECTRONICS MODULE COVER - FOR DESIGNJET 9000S PRINTER SERIES |
| Q6665-60023 |
POWER SUPPLY UNIT (PSU) - FOR DESIGNJET 9000S PRINTER SERIES |
| Q6665-60024 |
REAR COVER SENSOR - INCLUDES TWO SENSORS - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60025 |
HEATER CONTROL PANEL - LOCATED ON THE LEFT SIDE OF THE PRINTER - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60026 |
MEDIA LEVER SENSOR (CARRIAGE HOME POSITION SENOR) - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60027 |
CONTROL PANEL ASSEMBLY - LOACTED ON THE RIGHT SIDE OF THE PRINTER - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60028 |
MEDIA EDGE GUARD - INCLUDES EIGHT SCREWS AND FOUR SMALL GUIDES |
| Q6665-60029 |
CENTER PLATEN ASSEMBLY - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60030 |
VACUUM FAN ASSEMBLY - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60031 |
FRONT HEATER ASSEMBLY - HELPS TO RAPIDLY DRY INK AFTER MEDIA LEAVES THE PLATEN ASSEMBLY - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60032 |
REAR HEATER ASSEMBLY - HELPS TO RAPIDLY DRY INK AFTER MEDIA LEAVES THE PLATEN ASSEMBLY - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60033 |
MEDIA LEVEL SENSOR (CARIAGE HOME POSITION SENSOR) - LOCATED AT THE FRONT AND REAR OF THE PRINTER |
| Q6665-60034 |
LEVER KNOB - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60035 |
MEDIA-AXIS MOTOR - DRIVES THE DRIVE ROLLER ASSEMBLY - INCLUDES THE BELT, GEAR, SPRING, WASHER, AND BEARING |
| Q6665-60036 |
PINCHWHEEL ASSEMBLY - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60037 |
END-OF-MEDIA SENSOR - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60038 |
TAKE-UP-REEL (TUR) TENSION ROLLER - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60039 |
TAKE-UP-REEL (TUR) SENSOR - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60040 |
TAKE-UP-REEL (TUR) MOTOR - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60041 |
ENCODER STRIP - USED BY THE SENSOR IN THE CARRIAGE ASSEMBLY TO DETERMINE POSITION - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60042 |
CARRIAGE BELT - LONG BELT THAT MOVES THE CARRIAGE ASSEMBLY - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60043 |
DRIVE BELT TENSION PULLEY ASSEMBLY - INCLUDES THE MEDIA-AXIS MOTOR BELT |
| Q6665-60044 |
CARRIAGE (SCAN-AXIS) MOTOR ASSEMBLY - INCLUDES THE MEDIA-AXIS MOTOR BELT |
| Q6665-60045 |
CARRIER TENSION PULLEY - CARRIER BELT IDLER PULLEY |
| Q6665-60046 |
CARRIAGE ASSEMBLY TRAILING CABLE - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60047 |
PRINTHEAD CONNECTOR ASSEMBLY - CONTAINS THREE CABLES; ONE FOR EACH PRINTHEAD (LEFT AND RIGHT SIDE AND CENTER PRINTHEADS) |
| Q6665-60048 |
CARRIAGE PC BOARD - FOR THE DESIGNJET 9000S/10000S PRINTER SERIES |
| Q6665-60049 |
ENCODER SENSOR ASSEMBLY - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60050 |
LINE SENSOR - MEASURES CALIBRATION ACCURACY AND PRINTHEAD ALIGNMENT |
| Q6665-60051 |
AIRFLOW GUIDE ASSEMBLY - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60052 |
PRINTHEAD COOLING FAN - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60053 |
INK PUMP ASSEMBLY - INCLUDES THE INK PUMP TUBE AND NEEDLE |
| Q6665-60054 |
INK PUMP TUBE - FOR THE DESIGNJET 9000S/10000S PRINTER SERIES |
| Q6665-60055 |
INK SUPPLY STATION (ISS) ASSEMBLY - INSTALLED ON THE RIGHT SIDE OF PRINTER |
| Q6665-60056 |
INK SUPPLY STATION (ISS) ASSEMBLY - INSTALLED ON THE LEFT SIDE OF PRINTER |
| Q6665-60057 |
INK CARTRIDGE DOOR SENSOR - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60058 |
SUBTANK SENSOR - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60059 |
SUBTANK ASSEMBLY - INCLUDES THREE ASSEMBLIES |
| Q6665-60060 |
CAPPING STATION ASSEMBLY - FOR THE DESIGNJET 9000S/10000S PRINTER SERIES. HP DESIGNJET 9000/10000 / SEIKO 64S/100S PRINTER CAPPING STATION ASSEMBLY |
| Q6665-60061 |
CAPPING UNIT - INCLUDES SIX CAPS |
| Q6665-60062 |
SOLENOID ASSEMBLY - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60063 |
PRIMER ASSEMBLY - PRIMER ASSEMBLY - ONE UNIT |
| Q6665-60064 |
WIPING STATION ASSEMBLY - FOR THE DESIGNJET 9000S/10000S PRINTER SERIES |
| Q6665-60065 |
WIPER CLEANING ASSEMBLY - FOR THE DESIGNJET 9000S/10000S PRINTER SERIES |
| Q6665-60066 |
WIPER BLADE - FOR THE DESIGNJET 9000S/10000S PRINTER SERIES |
| Q6665-60067 |
WIPER BELT - INCLUDES TWO WIPER BELTS |
| Q6665-60068 |
WASTE INK BOTTLE - FOR THE DESIGNJET 9000S/10000S PRINTER SERIES |
| Q6665-60069 |
FOOT CASTERS - INCLUDES TWO FOOT CASTERS - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60070 |
CARRIAGE HEIGHT ADJUSTMENT TOOLS - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60071 |
PRINTHEAD POSITION ADJUSTMENT TOOLS - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60075 |
CAP HEIGHT ADJUSTMENT TOOL |
| Q6665-60076 |
TAKE-UP-REEL (TUR) PAPER HUB - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60077 |
RIGHT SIDE MEDIA FEED ASSEMBLY - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60078 |
LEFT SIDE MEDIA FEED ASSEMBLY - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60079 |
MEDIA FEED FLANGE - LOCATED ON THE MEDIA FEED ASSEMBLIES |
| Q6665-60080 |
WASTE INK BOTTLE LOCK - LOCKS THE WASTE INK BOTTLE IN PLACE |
| Q6665-60081 |
REAR END INK CARTRIDGE COVER - LOCATED ON THE LEFT SIDE OF THE PRINTER |
| Q6665-60083 |
9000S/10000S SERVICE MAINTENAN PREVENTIVE MAINTENANCE KIT - INCLUDES A WIPER CLEANING KIT, CAPPING UNIT, SCAN MOTOR BELT, BELT, PRIME ASSEMBLY, WIPER BLADE, AND WIPER BELTS. |
| Q6665-60084 |
FOOT ASSEMBLY FOR HP DESIGNJET 9000 SERIES |
| Q6665-60085 |
TUBES KIT 9000 FOR HP Q6665A |
| Q6665-60086 |
PMP TO SUBTANK TUBES |
| Q6665-60087 |
MEDIA HUB LOCK (MEDIA SECURING NUT) - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665-60088 |
CARRIAGE PLATE ASSEMBLY - LARGE METAL STRUCTURE WHERE CARRIAGE WILL BE MOUNTED |
| Q6665-60089 |
CLEANING SHEETS KIT |
| Q6665-60091 |
PLASTIC EXHAUST ATTACMENT - ATTACHES TO THE LOWER RIGHT SIDE COVER |
| Q6665-60092 |
MEDIA-AXIS MOTOR BELT - FOR THE DESIGNJET 9000S/10000S PRINTER SERIES |
| Q6665-60093 |
AIR DUMPER TO PH TUBES KIT |
| Q6665-60094 |
O-RINGSFRM PMP TO SUBTNK KIT |
| Q6665-60095 |
O-RINGS FROM SUBTANK TO PRINTHEAD KIT |
| Q6665-60100 |
CARRIAGE SHIELDS |
| Q6665-69001 |
9000 SERIES HEAD PRINTHEADS - SIX ARE USED - DOES NOT INCLUDE THE PRINTHEAD - FOR THE DESIGNJET 9000S PRINTER SERIES |
| Q6665A |
HP DESIGNJET 9000S PRINTER / HP DESIGNJET 9000S - 64 INCH WIDE FORMAT SOLVENT PRINTER |
| Q6666A |
HP DESIGNJET 9000SF PRINTER |
| Q6667A |
HP DESIGNJET HIGH SPEED DRYER - INCLUDES THE DRYER UNIT, SUPPORT STAY, FOOT WITH CASTOR (2), STAND (2), M5 X 12L HEXAGON SOCKET HEAD BOLT (16), HEXAGON BAR WRENCH, USERS GUIDE, AND POWER CORD (IN COMPLIANCE WITH REGIONAL POWER CONNECTIONS) |
| Q6668-60007 |
TURBINE ASSEMBLY - FOR 110-127VAC (+/- 10%) OPERATION |
| Q6668-60008 |
TURBINE ASSEMBLY - FOR 220-240VAC (+/- 10%) OPERATION |
| Q6668-60010 |
FOOT CASTORS - FOR THE DESIGNJET 9000S AIR PURIFIER SYSTEM (APS) |
| Q6668-60012 |
TUBES KIT - INCLUDES FOUR METER LONG TUBES FOR THE DESIGNJET 8000S/9000S AIR PURIFIER SYSTEM (APS) |
| Q6668-60017 |
APS TUBES KIT FOR HP DESIGNJET 1000 |
| Q6668-60022 |
ELECTRONICS MODULE ASSEMBLY - INCLUDES THE FRONT PANEL - FOR THE DESIGNJET 9000S/10000S AIR PURIFIER SYSTEM (APS) |
| Q6668-60023 |
TUBES KIT - INCLUDES SIX METER LONG TUBES FOR THE DESIGNJET 8000S/9000S/10000S AIR PURIFIER SYSTEM (APS) |
| Q6668C |
HP 9000S/10000S AIR PURIFIER SYSTEM (APS) - FOR 220V TO 240V OPERATION |
| Q6668D |
HP 9000S/10000S AIR PURIFIER SYSTEM (APS) - FOR 110-127VAC OPERATION |
| Q6668E |
HP DESIGNJET AIR PURIFIER SYSTEM (APS) - FOR 220-240VAC (+/- 10%) OPERATION - INCLUDES TWO FILTER ELEMENTS INSIDE, APS PRINTER CONNECTION SET, USERS GUIDE, AND A POWER CORD IN COMPLIANCE WITH REGIONAL POWER |
| Q6668F |
HP DESIGNJET AIR PURIFIER SYSTEM (APS) - FOR 110-127VAC (+/- 10%) OPERATION - INCLUDES TWO FILTER ELEMENTS INSIDE, APS PRINTER CONNECTION SET, USERS GUIDE, AND A POWER CORD IN COMPLIANCE WITH REGIONAL POWER |
| Q6669A |
Z3100 44 CARRIAGEASSY SV W/ MOD TC |
| Q6669B |
Q6669B |
| Q6670-60001 |
PRINTHEAD - THE DESIGNJET 8000S SERIES TAKES 6 PRINTHEADS, THIS IS FOR ONLY 1PC (PER MANUFACTURER). |
| Q6670-60003 |
LEFT SIDE TRIM ASSEMBLY - FOR THE DESIGNJET 8000S PRINTER SERIES |
| Q6670-60004 |
MAINTENANCE KIT DRAWER AND COVER ASSEMBLY - FOR THE DESIGNJET 8000S PRINTER SERIES |
| Q6670-60005 |
LEFT SIDE DOOR ASSEMBLY - FOR THE DESIGNJET 8000S PRINTER SERIES |
| Q6670-60006 |
RIGHT SIDE DOOR ASSEMBLY - FOR THE DESIGNJET 8000S PRINTER SERIES |
| Q6670-60007 |
RIGHT SIDE TRIM ASSEMBLY - FOR THE DESIGNJET 8000S PRINTER SERIES |
| Q6670-60008 |
LIFT-UP VIEWING WINDOW - DOES NOT INCLUDE HINGES |
| Q6670-60009 |
HINGE - FOR LIFT-UP WINDOW |
| Q6670-60010 |
TOP COVER ASSEMBLY - FOR THE DESIGNJET 8000S PRINTER SERIES |
| Q6670-60011 |
MANUAL HOLDER - ATTACHES TO REAR OF TOP COVER ASSEMBLY |
| Q6670-60012 |
RIGHT SIDE TOP COVER ASSEMBLY - FOR THE DESIGNJET 8000S PRINTER SERIES |
| Q6670-60013 |
HANDLE - RIGHT SIDE OF PLOTTER - RAISE TO LOAD PAPER |
| Q6670-60014 |
INK CARTRIDGE BAY COVER - FOR THE DESIGNJET 8000S PRINTER SERIES |
| Q6670-60015 |
RIGHT SIDE COVER ASSEMBLY - FOR THE DESIGNJET 8000S PRINTER SERIES |
| Q6670-60016 |
LEFT SIDE TOP COVER ASSEMBLY - FOR THE DESIGNJET 8000S PRINTER SERIES |
| Q6670-60017 |
LEFT SIDE BACK COVER - FOR THE DESIGNJET 8000S PRINTER SERIES |
| Q6670-60018 |
LEFT SIDE COVER ASSEMBLY - FOR THE DESIGNJET 8000S PRINTER SERIES |
| Q6670-60019 |
C14 CHASSIS PLUG (INLET) - FOR THE DESIGNJET 8000S PRINTER SERIES |
| Q6670-60020 |
MAIN PC BOARD - CONTROLS AND DRIVES THE PRINTER FOR THE DESIGNJET 8000S PRINTER SERIES |
| Q6670-60021 |
POWER SWITCH - FOR THE DESIGNJET 8000S PRINTER SERIES |
| Q6670-60022 |
HEATER RELAY BOARD - FOR THE DESIGNJET 8000S PRINTER SERIES |
| Q6670-60023 |
PRINTHEAD COOLING FAN - LOCATED BEHIND THE POWER SUPPLY UNIT |
