| Part |
Picture |
Description |
| C2169-67803 |
Service station sled assembly - Includes both cartridge caps |
| C2170-67805 |
Ink cartridge cover - Above cartridges when carriage is in home position on far right side of carriage path |
| C2170-67812 |
Input/ouput tray - Includes the left and right wings |
| C2170-67815 |
Paper access cover assembly - Lift-up top/front cover - Includes nameplate |
| C2171-40001 |
Flex holder - Supports flex cable between carriage and PCA |
| C2171-60126 |
Pressure plate assembly - Lifts paper stack to be printed |
| C4537-60035 |
Paper feed cleaning kit - Includes feed roller cleaning tool, software and instructions |
| C4549-40025 |
Rear slider - Prevents the carriage from tilting forward |
| C4562-20003 |
Idler pulley axel - Dowel pin for idler pulley |
| C4562-40022 |
Rotation limiter - Provides correct pressure to cap pen |
| C4562-40032 |
Belt tension bracket - Pivot bracket for idler pulley - Applies tension to the carriage belt |
| C2171-67810 |
Print Mechanism Assembly - Complete Mechanism With Carriage |
| 0905-1409 |
O-ring - Nitrile rubber, 6mm ID, 2mm diameter cross-section, 70 durometer |
| 51641A |
HP 41 Tricolor Ink Cartridge (51641A) |
| 51641AA |
HP Ink Crtg 41A Color AP |
| 51641AC |
HP Ink Crtg 41A Color Can |
| 51641AE |
HP Ink Crtg 41A Color EUR |
| 51641AL |
HP Ink Crtg 41A Color LAR |
| 51645A |
InkJet Crtg 45A Black Large NAM |
| 51645AA |
HP Inkjet Crtg 45A Black Large AP |
| 51645AC |
HP Inkjet Crtg 45A Black Large Can |
| 51645AE |
Black print cartridge (high capacity) - Prints approximately 840 pages based on 5% density on a 8-inch by 10-inch print area (Europe) |
| 51645AL |
Black print cartridge (high capacity) - Prints approximately 840 pages based on 5% density on a 8-inch by 10-inch print area (Latin America) |
| 51645G |
Black print cartridge (economy) - Prints approximately 415 pages based on 5% density on a 8 inch by 10 inch print area (USA) |
| 51645GA |
HP 45 Economy Black InkJet Print Cartridge - Prints approximately 415 pages based on 5% density on a 8-inch by 10-inch print area (Asia Pacific) |
| 51645GC |
Black print cartridge (economy) - Prints approximately 415 pages based on 5% density on a 8-inch by 10-inch print area (Canada) |
| 51645GL |
HP 45 Economy Black InkJet Print Cartridge - Prints approximately 415 pages based on 5% density on a 8-inch by 10-inch print area (Latin America) |
| 5183-3031 |
ASP (authorized service provider) training kit for DeskJet 800 family printers - Includes service manual CD-ROM and NTSC training video |
| 6040-0800 |
Special lubricating oil - For carriage slider rod surface - 1 quart bottle (.95 liter) |
| 6040-0911 |
Special lubricating oil - For carriage slider rod surface - (syringe with 35cc oil) |
| 8120-6173 |
Power cord (Dove Gray) - 2.3m (7.5ft) long - Has 90 degree (F) C13 receptacle (For 240VAC in the United Kingdom, Cyprus, Nigeria, Zimbabwe, and Singapore) |
| 8120-6174 |
Power cord (Dove Gray) - 2.3m (7.5ft) long - Has 90 degree (F) C13 receptacle (For 220VAC in Europe, Saudi Arabia, South Africa, and India) |
| 8120-6801 |
Power cord (Flint Gray) - 17 AWG, 2.3m (7.5ft) long - Has 90 degree (F) C13 receptacle (For 240VAC in the United Kingdom, Cyprus, Nigeria, Zimbabwe, and Singapore) |
| 8120-6802 |
Power cord (Flint Gray) - 2.3m (7.5ft) long - Has 90 degree (F) receptacle (for 220V in Europe, Saudi Arabia, South Africa, and India) |
| 8120-6805 |
Power cord (Flint Gray) - 18 AWG, 2.3m (7.5ft) long - Has 90 degree receptacle (for 120V in the USA, Canada, Mexico, Philippines, and Taiwan) |
| 8120-6806 |
Power cord (Flint Gray) - 17 AWG, 2.3m (7.5ft) long - Has 90 degree (F) receptacle (for 220V in Denmark) |
| 8120-6807 |
Power cord (Flint Gray) - 17 AWG, 2.3m (7.5ft) long - Has 90 degree (F) receptacle (for 220V in Switzerland) |
| 8120-8381 |
Power cord (Flint Gray) - 18 AWG, 1.8m (6.0ft) long - Has 90 degree (F) C13 receptacle (For 120VAC in the United States, Canada, Latin America, Korea, Taiwan, and Thailand) |
| 9170-1627 |
Ferrite assembly - Installed on flex cable assembly |
| 92215N |
Interface cable kit - For HP peripherals designed for use in an AppleTalk/Phonenet network - Not for Macintosh models that have recessed I/O connectors |
| 92215S |
RS-422 serial cable - 8-pin (M) to 8-pin (M) - 2.0m (6.6ft) long |
| 9301-1717 |
35cc syringe - For use with carriage slider rod lubricant |
| C1853A |
Media for HP C8127A |
| C2128-00002 |
Kicker spring - Provides tension for the kicker |
| C2128-00006 |
Separator spring - Provides pressure between the separator assembly and the center drive roller |
| C2128-40015 |
Left lifter cap - Holds the pressure plate lifter in place |
| C2128-40032 |
Center lifter cap - Holds the pressure plate lifter and the kicker spring in place |
| C2128-80075 |
Foam catch pad - Keeps paper catch from moving inadvertently |
| C2145-00016 |
Power supply cover - Shields and protects power supply PC board |
| C2145-00018 |
Encoder spring - Provides tension for the encoder strip and grounds the carriage rod to the carriage plate |
| C2145-00024 |
Preloader spring - Provides tension for the preloader bearing arm |
| C2145-00029 |
Paper catch spring - Provides tension for length adjustment |
| C2145-00031 |
Latch spring - Provides tension for tray latch |
| C2145-00032 |
Width spring - Provides friction for paper width adjuster |
| C2145-00033 |
ESD spring - Installed between ESD blade and carriage PC board |
| C2145-00037 |
ESD blade for HP DeskJet 870C Series |
| C2145-00042 |
Encoder stiffener - Prevents oscillation of encoder strip |
| C2145-00043 |
Clamp spring - Provides tension for the ink cartridge locking clamps |
| C2145-00044 |
Carriage rod spring |
| C2145-00046 |
Pivot spring - Provides tension for the pivot |
| C2145-00054 |
Paper motor ground strap |
| C2145-20007 |
Carriage rod - Shaft that the carriage assembly rides on |
| C2145-20019 |
Washer retainer - Holds carriage rod lubrication washers in place |
| C2145-40019 |
Pressure plate lifter - Also known as lifter shaft or paper lifter |
| C2145-40020 |
Lever arm - Provides linkage between the pivot assembly and the pressure plate lifter |
| C2145-40022 |
Separator link (Separator peg) |
| C2145-40023 |
Kicker - Restacks the paper in the paper input tray after the top sheet is removed |
| C2145-40027 |
I/O tray base - Holds the paper, pressure plate, width adjuster and paper catch |
| C2145-40029 |
Width adjuster - For single sheet or envelope feeder |
| C2145-40032 |
Width adjuster - Paper stack width adjuster |
| C2145-40038 |
Top cover - Does not include carriage access door |
| C2145-40040 |
Access door - Lift-up lid for cartridge/carriage access |
| C2145-40043 |
Light pipe - Transfers light from LED to keypad bezel |
| C2145-40044 |
Form feed actuator - Form feed button/arm from front panel |
| C2145-40045 |
Power button actuater - Power button/arm from front panel |
| C2145-40046 |
Door actuator - Actuates access door open switch |
| C2145-40047 |
Flex cable clamp |
| C2145-40048 |
Keypad bezel - Covers the keypad - Attaches to the front right of the top cover |
| C2145-40052 |
Lower paper guide |
| C2145-40058 |
Drive belt - For the print mechanism carriage assembly |
| C2145-40059 |
Eccentric bushing - Used to adjust pen-to-paper spacing (2 used) |
| C2145-40061 |
Tray latch - Holds paper tray in place |
| C2145-40064 |
OOPS flag - Out of paper sensor |
| C2145-40068 |
Side cover - Service station access door |
| C2145-40069 |
Key pivot - Link between panel actuators and micro switches |
| C2145-40083 |
Carriage pre-loader - Holds the carriage against the carriage rod |
| C2145-40084 |
Nose clamp - Holds black cartridge in place |
| C2145-40085 |
Nose clamp - Holds color cartridge in place |
| C2145-40090 |
Pivot stop adjuster - Installed near left end of carriage plate |
| C2145-40091 |
I/O deck - Holds wings and single sheet width adjuster |
| C2145-40092 |
I/O cap - Left side |
| C2145-40093 |
I/O cap - Right side |
| C2145-40101 |
Right pivot clamp (Right Z-STOP) - Holds the right end of the pivot assembly in place |
| C2145-40104 |
Fan support for HP DeskJet 850C Series |
| C2145-40105 |
Air filter housing |
| C2145-40110 |
Top cover bracket - Installed between old style ground plane and top cover |
| C2145-40117 |
Left pivot clamp (Left Z-STOP) - Holds the left end of the pivot assembly in place |
| C2145-40118 |
Pre-guide (For envelopes) |
| C2145-40140 |
Left wing - Holds printed paper after being ejected |
| C2145-40143 |
Right wing - Holds printed paper after being ejected |
| C2145-40151 |
Chimney wall - Wall support of spittoon |
| C2145-60010 |
Paper drive motor - Drives paper through printer |
| C2145-60011 |
Carriage motor assembly |
| C2145-60012 |
Service station motor |
| C2145-60025 |
Power cable - Has two 9-pin (F) connectors - 3.4cm (1.3in) long |
| C2145-60032 |
Carriage assembly flex cable - Overall length is 46.7cm (18.4in) |
| C2145-60036 |
Fan assembly for HP DeskJet 850C Series |
| C2145-60037 |
Pressure plate assembly - Lifts paper stack to be printed |
| C2145-60071 |
Blotter (absorber) assembly - Includes frame and blotter pads |
| C2145-60075 |
Base assembly - Bottom of printer - Includes rubber feet |
