|
![]() |
||
HP parts available for C9693A HP Color LaserJet 2500lse printerRB2-9904-000CN Airflow Guide - Airflow Guide (duct) - Black plastic insert piece which runs the width of the printer and has an air flow hole on right sideRB3-0025-000CN Airflow Guide - Airflow guide (duct) / fan holder bracket assembly (Quartz Gray plastic) RB3-0089-000CN Arm - Top cover rack arm (Black) - Plastic arm with teeth on bottom edge - Disengages the imaging drum/transfer assembly drive cams when the top door is open RB3-0089-030CN Arm - Top cover rack arm (Black) - Plastic arm with teeth on bottom edge - Disengages the imaging drum/transfer assembly drive cams when the top door is open RB1-8668-000CN Belt - Feed Guide Drive Belt RB1-8668-030CN Belt - Feed guide drive belt - Small belt approximately 5/16 inch wide with 'A' shaped ribs on it RB3-0063-000CN Belt - Paper feed belt - Small black rubber belt approximately 1/8 inch wide with little 'A' shaped ribs on it RB3-0035-000CN Bezel - Interface bezel (Quartz Gray plastic) - Vertical cover that surronds the interface connectors RB2-2973-000CN Bushing - Support bushing RB2-3043-000CN Bushing - Left roller bushing - Acts as the bearing and retainer for the left end of the paper pickup roller assembly (tray 1) RB2-3044-000CN Bushing - Right roller bushing - Acts as the bearing and retainer for the right end of the paper pickup roller assembly (tray 1) RB2-9808-000CN Bushing - Bushing/shaft retainer assembly - Black plastic RB2-9809-000CN Bushing - Bushing/shaft retainer assembly (White plastic) RB3-0014-000CN Bushing - Bushing assembly (black plastic bushing with small guide roller on top) RS5-1635-000CN Bushing - Shaft bushing for HP Color LaserJet 1500 Series RS5-1637-000CN Bushing - Bushing (black plastic) RS5-1638-000CN Bushing - Bushing for HP Color LaserJet 1500 Series 5063-1256 Cable - IEEE-1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36-pin Centronics (M) connector (type B) - 2.0m (6.6ft) long 5063-1257 Cable - IEEE 1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36-pin Centronics (M) connector (type B) - 3.0m (9.8ft) long C2950A Cable - IEEE 1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36-pin Centronics (M) connector (type B) - 2.0m (6.6ft) long C2951A Cable - IEEE-1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36 pin Centronics (M) connector (type B) - 3.0m (9.8ft) long C6518A Cable - Universal Serial Bus (USB) interface cable - Type 'A' connector to type 'B' connector - 2.0m (6.6ft) long C9706-60104 Cable - Flat flexible cable Q3948-60144 Cable - Flat flexible cable (FFC) assembly - Connects between the formatter assembly (J1001) and the DC controller board (J101) RG5-6971-000CN Cable - Cable assembly (two 3-pin connectors and a spad lug) RG5-6974-000CN Cable - Cable assembly for HP Color LaserJet 1500 Series RG5-7106-000CN Cable - Cable assembly (two 2-pin connectors) RG5-7107-000CN Cable - Cable assembly (8-pin, red wire) RG5-7108-000CN Cable - Cable assembly (two 8-pin connectors, Purple wire) RG5-7109-000CN Cable - Cable assembly (two 7-pin connectors) RG5-7114-000CN Cable - Cable assembly (two 4-pin connectors) with shield RG5-7114-020CN Cable - Cable assembly (two 4-pin connectors) with shield - Connects between the cartridge drive motor and the DC controller board RG5-7115-000CN Cable - Cable assembly (two 3-pin connectors) RG5-7117-000CN Cable - Cable assembly (two 3-pin connectors) RG5-7122-000CN Cable - Cable assembly - 'Y' type cable (three connectors) - The 14-pin connector splits into an 8-pin connector and a 6-pin connector RG5-7123-000CN Cable - Grounding cable assembly RG5-7126-000CN Cable - Cable assembly (two 5-pin connectors) RG5-7128-000CN Cable - Cable assembly (four 3-pin connectors) RG5-7129-000CN Cable - Cable assembly (two connectors and two spade lugs) RG5-7130-000CN Cable - High voltage cable assembly RG5-7144-000CN Cable - Cable assembly (with seven connectors) RG5-7145-000CN Cable - Front cable assembly (six connectors) RG5-7146-000CN Cable - High voltage cable assembly (two 15-pin connectors and two 14-pin connectors) RG5-7161-000CN Cable - Cable assembly (two 3-pin connectors and a spad lug) RH2-5524-000CN Cable - Flat flexible cable (FFC) assembly - Connects between the formatter assembly (J1001) and the DC controller board (J101) RG5-6910-080CN Carousel - Carousel (Rotary) assembly - Includes the carousel assembly, the support assembly, end plates, drive gears and shaft, sensors, and cables C9700-67901 Cartridge - HP Color LaserJet smart Black print cartridge - Will print approximately 5,000 pages at 5% coverage C9700A Cartridge - HP Color LaserJet smart Black print cartridge - Will print approximately 5,000 pages at 5% coverage C9701-67901 Cartridge - HP Color LaserJet smart Cyan print cartridge - Will print approximately 5,000 pages at 5% coverage C9701A Cartridge - HP Color LaserJet smart Cyan print cartridge - Will print approximately 5,000 pages at 5% coverage C9702-67901 Cartridge - HP Color LaserJet smart Yellow print cartridge - Will print approximately 5,000 pages at 5% coverage C9702A Cartridge - HP Color LaserJet smart Yellow print cartridge - Will print approximately 5,000 pages at 5% coverage C9703-67901 Cartridge - HP Color LaserJet smart Magenta print cartridge - Will print approximately 5,000 pages at 5% coverage C9703A Cartridge - HP Color LaserJet smart Magenta print cartridge - Will print approximately 5,000 pages at 5% coverage 5090-3379 Cleaner - Toner cleaning cloth - Specially treated cloth for absorbing toner (1 per package) - Ideal for cleaning up toner spills WT2-5056-000CN Clip - Cable clip - `C` shaped White plastic XD2-1100-502CN Clip - E-ring clip for HP Color LaserJet 1500 Series RH7-5366-000CN Clutch - Electromagnetic clutch assembly (24V) - Electrical clutch between the clutch drive gear and shaft RH7-5389-000CN Clutch - Electromagnetic clutch assembly (24V) - Electrical clutch between the clutch drive gear and shaft RH2-5519-000CN Connector - Connector assembly - For optional paper tray RH2-5520-000CN Connector - Connector for the fusing assembly - Seven small contol pins plus three separated high current pins WS1-6336-000CN Connector - Connector assembly - For optional bottom paper tray WT2-5737-000CN Connector - Drawer connector - Connector located on bottom of tray assembly frame on right side, which connects tray assemblies to each other RG5-6927-000CN Control Panel - Control panel assembly (mechanical only) - Includes the 'Rotate Carousel', 'Cancel Job' and the 'Go' buttons, plus the various indicator light pipes - All switches and LED's are on the formatter PC board RB2-9916-020CN Cover - Cover - For the engaging motor (PM704) - Mounts on the upper left side of the rear frame assembly RB3-0028-000CN Cover - Left side cover (Quartz Gray) - Does not include any attaching parts RB3-0030-000CN Cover - Upper rear cover (Quartz Gray) - Mounts on the upper rear of the printer above the face-up output tray door RB3-0032-000CN Cover - Face-down paper output L-Shaped cover ( Blue) - Serves as the rear of the tray for the face-down output tray on top of the printer RB3-0052-000CN Cover - Gear Cover (Small Black plastic cover) - Covers the left end of the feed drive shaft RB3-0102-000CN Cover - Front inner cover (Blue) - Mounts on the front frame above the multi-purpose input tray RB3-0103-000CN Cover - Front lower cover (blue plastic) - Front lower strip below the multi-purpose input tray - Has recessed area for the printer logo RB3-0104-000CN Cover - Roller cover - Covers the multipurpose paper pickup roller assembly - Mounts on the lower front of the front frame assembly RB3-0120-000CN Cover - Solenoid cover (Steel) - For magnetic wave sheilding RB3-0120-020CN Cover - Solenoid cover (Steel) - For magnetic wave sheilding - Mounts over the solenoid on the right side of the front frame assembly RG5-6900-000CN Cover - Top cover assembly (blue plastic) - Includes the molded-in face-down output tray and the lift-up top cover door assembly RG5-6902-000CN Cover - Left side cover assembly (Quartz Gray) plastic - Includes the power switch button, rod and spring (The power switch is located on the low voltage power supply board) RG5-6953-000CN Cover - Right side cover assembly (Quartz Gray) plastic - Includes the DIMM memory door RB2-6248-000CN Damper - Damper assembly (Gray plastic piece with small 13-tooth gear on it) RB3-0033-000CN Door - Memory access door (Quartz Gray perforated plastic) - Allows access to the printer memory slots - Mounts on the right side cover RF5-4007-000CN Door - Top cover door (blue plastic) - For accessing the toner cartridges and the imaging drum/transfer assembly - Mounts to the top cover frame RG5-6911-000CN Drive Assembly - Rotary drive assembly - Includes the carousel rotating motor (DCM703), toner cartridge drive motor (PM705), developing rotary stopper solenoid (SL93), bracket, and gears C9704-67901 Drum - Imaging drum/transfer assembly cartridge - Inserts into printer through the top door - Life expectancy is 20,000 pages for black print ONLY, 5,000 pages for color (Typical combined life is approximately 6,000 to 8,000 pages) C9704A Drum - Imaging drum/transfer assembly cartridge - Inserts into printer through the top door - Life expectancy is 20,000 pages for black print only, 5,000 pages for color (Typical combined life is approximately 6,000 to 8,000 pages) RH7-1537-000CN Fan - Cooling fan (Panaflo Model FBA08T24H - 80mm X 80mm X 15mm high, DC brushless, 24V DC, 190mA) RH7-1630-000CN Fan - Cooling fan (Panaflo Model FBA08T24H - 80mm X 80mm X 15mm high, DC brushless, 24V DC, 190mA) RB2-9925-000CN Flag - Sensor arm and flag - Activates the photosensor (Does NOT include the roller) RB3-0111-000CN Flag - Paper flag - Plastic rod with paper sensing flag on one end and sensor activator flag on the other RB3-0135-000CN Flag - Test print flag (Black lever) RB2-6297-000CN Foot - Rubber foot - Square self-adhesive rubber foot RG5-6903-000CN Fuser Assembly - Fuser Assembly (For 110V to 127V operation) - Bonds the toner to the paper with heat RG5-6913-000CN Fuser Assembly - Fuser Assembly (For 220V to 240V operation) - Bonds the toner to the paper with heat RM1-3525-000CN Fuser Assembly - Fusing assembly (For 220V to 240V operation) - Bonds the toner to the paper with heat - Slides in and locks in lower rear of printer RB3-0022-000CN Gear - 22 tooth gear (Black plastic) - Small gear with diagonally cut teeth RB3-0091-000CN Gear - 16 tooth gear (Black plastic) - Gear with large stop tooth and shaft lock tab RB3-0092-000CN Gear - 15 tooth gear with drive shaft (Black plastic) RG5-6938-000CN Gear - Gear assembly - Metal plate with two White plastic gears attached RS7-0418-000CN Gear - 26 tooth gear (Black plastic) - Has 1/8th portion of gear cut away RS7-0424-000CN Gear - Dual gear - 20 tooth / 40 tooth RS7-0425-000CN Gear - 30 tooth gear (White plastic) RS7-0426-000CN Gear - Dual gear - 26 tooth / 50 tooth (White plastic) RS7-0428-000CN Gear - 30 tooth gear (White plastic) RS7-0429-000CN Gear - 26 tooth gear (White plastic) - Has recess for shaft drive pin RS7-0435-000CN Gear - Dual gear - 32 tooth / 37 tooth (White plastic) RS7-0436-000CN Gear - Dual gear - 37 tooth / 43 tooth (White plastic) RS7-0437-000CN Gear - 51 tooth gear (White plastic) RG5-6938-030CN Gear Assembly - Gear assembly - Metal plate with two White plastic gears attached RB2-9942-000CN Ground - Grounding plate - Provides grounding for the top-of-page sensor and shielding for the density sensor boards RB3-0119-000CN Ground - Grounding plate RB2-9903-000CN Guide - Cable guide (Quartz Gray plastic) RB2-9912-000CN Guide - Top output bin guide - Small curved ribbed black plastic piece RB2-9954-000CN Guide - Left paper feed guide (small Black plastic arm) RB2-9955-000CN Guide - Right paper feed guide (small Black plastic arm) RF5-4049-000CN Guide - Entrance guide assembly - Angled metal guide between the registration roller and the transfer roller RG5-6929-000CN Guide - Separation guide assembly - Includes the plastic guide, label, and the two small spring loaded rollers RG5-6930-000CN Guide - Lower separation guide assembly - Includes the guide bracket, paper output sensor (PS1) and flag, exit drive shaft with two rubber rollers, shaft gear, and idler gear RG5-6935-000CN Guide - Left cartridge guide assembly RG5-6935-020CN Guide - Left cartridge guide assembly RG5-6951-000CN Guide - Paper guide assembly - Paper width adjustable guide assembly for the multi-purpose front input tray (tray 1) RB2-3041-000CN Hinge - Tray hinge - For the left side of the multi-purpose front input tray (tray one) RB2-3042-000CN Hinge - Tray hinge - For the right side of the multi-purpose front input tray (tray one) RB2-6405-000CN Hinge - Tray hinge - For the left side of the multi-purpose front input tray (Tray 1) RB2-6406-000CN Hinge - Tray hinge - For the right side of the multi-purpose front input tray (Tray 1) RB2-9924-000CN Holder - Sensor assembly mounting holder RB3-0006-000CN Holder - Holder - Housing for the fusing connector assembly RB3-0023-000CN Holder - Interlock switch holder (Quartz Gray plastic) - Does NOT include the micro-switch RB3-0007-000CN Insulator - Insulating sheet (Transparent plastic) RB3-0056-000CN Insulator - Insulating sheet (Transparent plastic) RS6-8662-000CN Label - Label for Color LaserJet 2500 Series, Color LaserJet 1500 Series, Color LaserJet 2550 Series RG5-6880-000CN Laser Scanner - Laser/scanner assembly RG5-6890-030CN Laser Scanner - Laser/scanner assembly RB3-0178-000CN Lever - Right side lock release lever RB3-0179-000CN Lever - Left side lock release lever C9706-90926 Manual - Manual for Color LaserJet 2500 Series C7845A Memory - 32MB, 100-pin SDRAM DIMM memory module C7846A Memory - 64MB SDRAM - 100MHz synchronous DRAM - DIMM package C9121A Memory - 128MB, 100-pin SDRAM DIMM memory module Q7707AX Memory - 32MB, 100-pin SDRAM DIMM memory module Q7708AX Memory - 64MB SDRAM - 100MHz synchronous DRAM - DIMM package Q7709AX Memory - 133 MHz 128MB, 100-pin SDRAM DIMM memory module Synchronous DRAM DIMM RF5-4010-000CN Motor - Main motor assembly - Large motor mounted on a controller PC board RF5-4010-020CN Motor - Main motor assembly - Large motor mounted on a controller PC board - Mounts on the inside of the metal right side frame assembly RG5-6958-000CN Motor - Rotary motor assembly RH7-1533-000CN Motor - Stepping motor - 24V DC RH7-1535-000CN Motor - Stepping motor (24V) RH7-1625-000CN Motor - Stepping motor - 24VDC RH7-1629-000CN Motor - Stepping motor - 24V DC RB2-9960-000CN Pad - Separation pad assembly - Includes the gray plastic frame with the rubber insert strip - For the cassette on the 250-sheet and 500-sheet input tray assemblies - Mounts in the paper cassette tray assembly Replaced by RF5-4258-020CN RF5-4012-000CN Pad - Separation pad assembly - Includes the separation pad, holder and spring RF5-4047-000CN Pad - Light blocking pad assembly - Black plastic frame with soft rubber gasket and stiff conductive Mylar piece (grounded) 5851-1468 Paper - LaserJet printer family paper specification guide Q1298A Paper - LaserJet Satin finish tough paper - A size (8.5 x 11-inches) - Will not tear and will withstand outdoor weather conditions - Can print on both sides Q1298B Paper - LaserJet Satin finish tough paper - A4 size (21.0cm x 29.7cm) - Will not tear and will withstand outdoor weather conditions - Can print on both sides - 50 sheets per box C9145-67901 PC Board - Formatter board assembly - Includes the formatter board and all the metal cage covers C9145-69001 PC Board - Formatter board assembly - Includes the formatter board and all the metal cage covers C9705-69003 PC Board - DC controller board - Mounts on the left side of the printer (Behind the formatter board assembly) RG5-6959-060CN PC Board - DC controller board RG5-6964-000CN PC Board - Carousel position and toner level photoelectric sensor PC board - L Shaped PC board with the two sensors RG5-6965-000CN PC Board - Waste toner sensor PC board - Small board with an LED and photoelectric sensor - Monitors the level of the excess toner deposited in the imaging drum/transfer assembly RG5-6967-000CN PC Board - Registration sensor PC Board - Small board with flag activated photosensor RG5-7609-000CN PC Board - Carousel position and toner level photoelectric sensor PC board - `L` Shaped PC board with the two sensors RG5-7612-000CN PC Board - Top of page photoelectric sensor PC board - Includes the photoelectric top of page sensor and the print engine test switch RG5-7613-000CN PC Board - Registration sensor PC Board - Small board with flag activated photosensor RH7-7146-000CN PC Board - Density photoelectric sensor PC board RH7-7158-000CN PC Board - Density photoelectric sensor PC board WG8-5382-000CN PC Board - Sensor PC board - Small board with flag activated photosensor WG8-5593-000CN PC Board - Sensor PC board - Small board with flag activated photosensor WG8-5836-000CN PC Board - PHOTOINTERRUPTER Stapler Stacker J3110A PC Board Interface - Ethernet 10Base-T (RJ-45) EIO network GENUINE HP JETDIRECT 600N internal print server PC board J3111A PC Board Interface - Ethernet 10Base-T/10Base2 and LocalTalk (RJ-45, BNC, LocalTalk) EIO network PCA J4135A PC Board Interface - JetDirect connectivity card - Has one USB port, one serial (DB9) port, and one LocalTalk port - Plugs in one of the EIO slots on selected DesignJet and LaserJet printers J4167A PC Board Interface - JetDirect 610N token ring LAN interface board - DB-9 and RJ-45 connectors J6057AR PC Board Interface - JetDirect 615N internal print server (10Base-T and 100Base-TX) LAN interface board - Plugs into peripheral EIO slot - Has a RJ-45 connector - Comes with software on CD-ROM and manual J6058A PC Board Interface - HP JetDirect 680N internal wireless IEEE-802.11b (Wi-Fi) print server - Plugs into peripheral EIO slot J7934G PC Board Interface - HP JetDirect 620n internal print server - 10BaseT and 100BaseTX LAN interface board - Plugs into peripheral EIO slot - Has an RJ-45 connector - Comes with software on CD-ROM and manual on CD-ROM RB2-9916-000CN Plate - Mounting/grounding plate RB3-0010-030CN Plate - Feed plate - Center metal plate with slots that the ribs on the middle frame assembly go through RB3-0057-000CN Plate - Transfer slide plate - Small 'U' shaped metal insert plates RB3-0065-000CN Plate - Contact plate - copper clad metal spring - Holds the left end of the small 500 Meg-ohm resistor RB3-0286-000CN Plate - Contact plate for HP Color LaserJet 2500 Seriess 8120-6800 Power Cord - Power cord (Flint Gray) - 3-wire, 16 AWG, 2.3m (7.5ft) long - Has straight (F) C13 receptacle (for 240V in Israel) 8120-6809 Power Cord - Power cord (Dove Gray) - 2.3m (7.5ft) long - Has straight (F) receptacle (For 240V operation in the U.K., Hong Kong, Singapore, Malaysia) 8120-6810 Power Cord - Power cord (Flint Gray) - 2.3m (7.5ft) long - Has straight (F) receptacle (For 240V operation in Australia, New Zealand) 8120-6811 Power Cord - Power cord (Flint Gray) - 17 AWG, 2.3m (7.5ft) long - Has straight (F) C13 receptacle (for 220V in Europe, Saudi Arabia, South Africa, India, and Korea) 8120-6812 Power Cord - Power cord (Flint Gray) - 18 AWG, three conductor, 2.3m (7.5ft) long - Has straight (F) C13 receptacle (For 120VAC in the United States, Canada, Mexico, Philippines, and Taiwan) 8120-6813 Power Cord - Power cord (Dove Gray) - Three Conductor, 2.3M (7.5ft) long - Has straight (F) C13 receptacle (For 240VAC in the United Kingdom, Hong Kong, Singapore, Malaysia) 8120-6814 Power Cord - Power cord (Flint Gray) - 17 AWG, three conductor, 2.3m (7.5ft) long - Has straight (F) C13 receptacle (For 220VAC in Denmark) 8120-6815 Power Cord - Power cord (Flint Gray) - 17 AWG, three conductor, 2.3m (7.5ft) long - Has straight (F) C13 receptacle (For 220VAC in Switzerland) RG5-6960-000CN Power Supply - High voltage power supply board (HVT) assembly - Has contacts for the eight high voltage springs in the printer RG5-7124-000CN Power Supply - Sub-high voltage board - Small auxillary PC board RG5-7616-000CN Power Supply - Sub-high voltage board - Small auxillary PC board RH3-2241-000CN Power Supply - Low voltage power supply - For 110V to 127V AC operation - Includes the AC power input connector and power switch RH3-2243-000CN Power Supply - Low voltage power supply - For 220V to 240V AC operation - Includes the AC power input connector and power switch RG5-6943-000CN Pressure Assembly - Carousel pressure (support) assembly - Includes the main rear support, E-label reader assembly, engaging sensor, and the engaging rod shaft RG5-6943-020CN Pressure Assembly - Carousel pressure (support) assembly - Includes the main rear support, E-label reader assembly, engaging sensor, and the engaging rod shaft - Primary support structure for the toner cartridge carousel J6057A Print Server - JetDirect 615N internal print server LAN interface board - 10Base-T and 100Base-TX - Plugs into peripheral EIO slot, has RJ-45 connector J7934A Print Server - JetDirect 620N Ethernet Print Server, internal print server LAN interface board - 10Base-T and 100Base-TX - Plugs into peripheral EIO slot, has RJ-45 connector. RB3-0061-000CN Pulley - Pulley roller (accommodates three feed belts) - Small black roller approximately 3.49cm (1-3/4 inches) long with three ball type pulleys RB3-0067-000CN Pulley - Pulley roller (accommodates one feed belt) - Small black roller approximately 1.59cm (5/8 inch) long with one ball type pulley RB3-0090-000CN Rack Slide - Rack slide - White plastic piece with gear teeth layed out in rack form on both sides RG5-6956-000CN Reader - E-label reader (contact board ONLY) - Connects the cartridge nonvoliatile memory to the DC controller board RG5-6957-000CN Reader - E-label reader assembly - Connects cartridge nonvoliatile memory to the DC controller board RG5-7131-000CN Reader - E-label reader (contact board ONLY) - Connects the cartridge nonvoliatile memory to the DC controller board RG5-7132-000CN Reader - E-label reader assembly - Connects cartridge nonvoliatile memory to the DC controller board C9693A-Repair_LaserJet Repair Service - Ship your product to us for a small diagnostic fee; and a professional service job. We will contact you with repair total and your diagnostic fee will be waived if unit is repaired. Service warranty is 30days labor and 90days for parts. Extended warranty option is available. RB3-0037-000CN Rod - Power switch rod - Goes between the power button and the power switch on the low voltage power supply board RB2-7195-000CN Roller - Sensor flag roller (small White plastic roller) RB2-9908-000CN Roller - Pressure roller (small Black hard plastic disk shaped roller) RB2-9909-000CN Roller - Pressure roller (small Black hard plastic 'solid' roller) RB3-0012-000CN Roller - Belt roller - Small oval shaped roller approximately 1-3/4 inches long RB3-0160-000CN Roller - Paper pickup roller ('D' shaped) RF5-4040-020CN Roller - Transfer roller assembly - Long black foam type roller - Transfers static charge to paper Part RF5-4040-000CN is no longer supplied. Please order the replacement, RF5-4040-020CN RG5-6897-020CN Roller - Upper top bin output roller assembly - Includes the shaft with four rubber rollers, two bushing/shaft retainers, two anti-reversing flaps, and the drive gear RG5-6936-000CN Roller - Lower top bin output roller assembly - Includes the shaft with four rubber rollers, two bushing/shaft retainers, and the drive gear RG5-6939-020CN Roller - Registration roller assembly - Includes the roller, bushings, mounting plate, paper sensor, and the sensor flag RG5-6952-000CN Roller - Paper pickup roller assembly - Includes the shaft, guide assembly cams, the D-shaped roller, and roller retainers - Picks paper from the multipurpose front input tray (tray 1) RG5-6952-020CN Roller - Paper pickup roller assembly - Includes the shaft, guide assembly cams, the D-shaped roller, and roller retainers - Picks paper from the multipurpose front input tray (tray 1) - Mounts in the lower portion of the front frame assembly C9693A-Manual_Color Service Manual - Printer Service Manual - Includes troubleshooting, error messages, paper jams, parts and parts diagrams. RB2-4933-000CN Shaft - Lock release shaft - Small shaft with locking tab - Does NOT include the lock release lever RB3-0011-000CN Shaft - Feed drive shaft - Long shaft with eight feed belt ball type pulleys and one ribbed feed guide drive belt pulley RB3-0060-020CN Shaft - Idler gear shaft - Short metal rod RB2-9932-000CN Shield - RFI shield - Parallel wire form mounted over the fan RG5-6940-050CN Shutter - Registration shutter assembly - Includes the metal roller, mounting frame, grounding springs, and the dual coupling gear RG5-6932-060CN Sideplate - Right side plate assembly - Includes the front half of the metal frame assembly, gears, imaging drum/transfer assembly drive cams, cover engaging mechanism, roller engaging clutch (CL2), and main drive motor (DCM701) RG5-6932-070CN Sideplate - Right side plate assembly - Includes the front half of the metal frame assembly, gears, imaging drum/transfer assembly drive cams, cover engaging mechanism, roller engaging clutch (CL2), and main drive motor (DCM701) - Mounts on the right side RG5-6934-000CN Sideplate - Right rear side plate assembly - Includes the rear half of the metal right side plate, the fusing assembly drive motor and the three associated gears RG5-6942-000CN Sideplate - Left side carousel plate assembly - End plate under the rotational toner cartridge carousel - Includes all of the high voltage contacts for the toner cartridges RG5-6942-030CN Sideplate - Left side carousel plate assembly - End plate under the rotational toner cartridge carousel - Includes all of the high voltage contacts for the toner cartridges - Mounts on the metal carousel support frame RH7-5337-000CN Solenoid - Solenoid assembly RH7-5340-000CN Solenoid - Solenoid assembly RH7-5384-000CN Solenoid - Solenoid assembly RB2-9905-000CN Spring - Torsion spring for HP Color LaserJet 2500 Series RB2-9906-000CN Spring - Torsion spring for HP Color LaserJet 1500 Series RB2-9952-000CN Spring - Tray 1 flag spring - Provides torsion for the tray 1 paper sensor flag RB3-0015-000CN Spring - Compression spring RB3-0016-000CN Spring - Electrical contact spring - Spring steel wire with compression springs formed on both ends RB3-0042-000CN Spring - Electrical contact spring RB3-0043-000CN Spring - Electrical contact spring RB3-0044-000CN Spring - Electrical contact spring RB3-0045-000CN Spring - Electrical contact spring RB3-0046-000CN Spring - Electrical contact spring RB3-0047-000CN Spring - Electrical contact spring RB3-0048-000CN Spring - Electrical contact spring RB3-0121-000CN Spring - Right retaining spring - Helps to secure and ground the imaging drum/transfer assembly in the printer RB3-0122-000CN Spring - Left retaining spring - Helps to secure the imaging drum/transfer assembly in the printer RS6-2030-000CN Spring - Tension spring for HP Color LaserJet 1500 Series RS6-2759-000CN Spring - Compression spring RS6-2766-000CN Spring - Tension spring for HP Color LaserJet 1500 Series RB3-0009-000CN Static Dissipater - Static eliminator ground plate - Right angled metal piece with small teeth on top edge RB3-0062-000CN Support - PC board support (Black plastic holder) RG5-6907-030CN Support - Laser/scanner support assembly (sheet metal plate) RH7-6051-000CN Switch - Microswitch with lever activator RH7-7149-000CN Thermistor - Thermistor for HP Color LaserJet 2500 Series RH7-7159-000CN Thermistor - Thermistor for HP Color LaserJet 2820 Series RB3-0019-000CN Tray - Toner catch tray (curved Black plastic piece) - Holds residual toner from photosensitive drum RB3-0176-000CN Tray - Face-Up output tray door (ONLY) RG5-6931-000CN Tray - Face-up output tray assembly - Includes the pull-down door and fusing assembly locking bracket (Does NOT include the lock releases) C9698A Tray Assembly - Optional 250 sheet paper input tray - Includes tray base which attaches to printer, and the slide out paper tray - Accommodates 148mm x 210mm (5.8 x 8.3 inches) to 216mm x 356mm (8.5 x 14 inches) media - Only one 250 sheet tray supported per printer C9699A Tray Assembly - Optional 500 sheet paper input tray - Includes tray base which attaches to tray 2, and the slide out paper tray - Accommodates 216mm x 279mm (8.5 x 11 inches) or 210mm x 279mm (8.3 x 11.7 inches) media - Optional 250 sheet tray must be installed first RG5-6937-000CN Tray Assembly - Multi-purpose front input tray assembly (tray-1) - Includes the front cover piece, pull-out paper support, and the flip-out extender |
||
![]() |
|
|
Copyright © 2019 Partshere.com Privacy Policy Terms and Conditions Send us your Feedback |