| RB2-9904-000CN |
Airflow Guide - Airflow Guide (duct) - Black plastic insert piece which runs the width of the printer and has an air flow hole on right side |
| RB3-0025-000CN |
Airflow Guide - Airflow guide (duct) / fan holder bracket assembly (Quartz Gray plastic) |
| RB3-0089-000CN |
Arm - Top cover rack arm (Black) - Plastic arm with teeth on bottom edge - Disengages the imaging drum/transfer assembly drive cams when the top door is open |
| RB3-0089-030CN |
Arm - Top cover rack arm (Black) - Plastic arm with teeth on bottom edge - Disengages the imaging drum/transfer assembly drive cams when the top door is open |
| RB1-8668-030CN |
Belt - Feed guide drive belt - Small belt approximately 5/16 inch wide with 'A' shaped ribs on it |
| RB3-0063-000CN |
Belt - Paper feed belt - Small black rubber belt approximately 1/8 inch wide with little 'A' shaped ribs on it |
| RB3-0035-000CN |
Bezel - Interface bezel (Quartz Gray plastic) - Vertical cover that surronds the interface connectors |
| RG5-6915-030CN |
Body - 250 sheet cassette tray main body assembly - Includes the main structure frame, paper stops, lift plate, springs, and the separation pad assembly - Does NOT include the blue plastic front cover |
| RB2-2895-000CN |
Bushing - Shaft bushing/retainer - Right side pickup roller support bushing |
| RB2-2896-000CN |
Bushing - Shaft bushing/retainer - Left side pickup roller support bushing |
| RB2-2897-000CN |
Bushing - Shaft bushing/retainer |
| RB2-2897-020CN |
Bushing - Shaft bushing/retainer |
| RB2-2973-000CN |
Bushing - Support bushing |
| RB2-3043-000CN |
Bushing - Left roller bushing - Acts as the bearing and retainer for the left end of the paper pickup roller assembly (tray 1) |
| RB2-3044-000CN |
Bushing - Right roller bushing - Acts as the bearing and retainer for the right end of the paper pickup roller assembly (tray 1) |
| RB2-9808-000CN |
Bushing - Bushing/shaft retainer assembly - Black plastic |
| RB2-9809-000CN |
Bushing - Bushing/shaft retainer assembly (White plastic) |
| RB3-0014-000CN |
Bushing - Bushing assembly (black plastic bushing with small guide roller on top) |
| RS5-1635-000CN |
Bushing - Shaft bushing for HP Color LaserJet 1500 Series |
| RS5-1636-000CN |
Bushing - Shaft bushing for HP Color LaserJet 2820 Series |
| RS5-1637-000CN |
Bushing - Bushing (black plastic) |
| RS5-1638-000CN |
Bushing - Bushing for HP Color LaserJet 1500 Series |
| 5063-1256 |
Cable - IEEE-1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36-pin Centronics (M) connector (type B) - 2.0m (6.6ft) long |
| C2950A |
Cable - IEEE 1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36-pin Centronics (M) connector (type B) - 2.0m (6.6ft) long |
| C2951A |
Cable - IEEE-1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36 pin Centronics (M) connector (type B) - 3.0m (9.8ft) long |
| C6518A |
Cable - Universal Serial Bus (USB) interface cable - Type 'A' connector to type 'B' connector - 2.0m (6.6ft) long |
| C9706-60104 |
Cable - Flat flexible cable |
| Q3948-60144 |
Cable - Flat flexible cable (FFC) assembly - Connects between the formatter assembly (J1001) and the DC controller board (J101) |
| RG5-6971-000CN |
Cable - Cable assembly (two 3-pin connectors and a spad lug) |
| RG5-6974-000CN |
Cable - Cable assembly for HP Color LaserJet 1500 Series |
| RG5-7106-000CN |
Cable - Cable assembly (two 2-pin connectors) |
| RG5-7107-000CN |
Cable - Cable assembly (8-pin, red wire) |
| RG5-7108-000CN |
Cable - Cable assembly (two 8-pin connectors, Purple wire) |
| RG5-7109-000CN |
Cable - Cable assembly (two 7-pin connectors) |
| RG5-7114-000CN |
Cable - Cable assembly (two 4-pin connectors) with shield |
| RG5-7114-020CN |
Cable - Cable assembly (two 4-pin connectors) with shield - Connects between the cartridge drive motor and the DC controller board |
| RG5-7115-000CN |
Cable - Cable assembly (two 3-pin connectors) |
| RG5-7117-000CN |
Cable - Cable assembly (two 3-pin connectors) |
| RG5-7122-000CN |
Cable - Cable assembly - 'Y' type cable (three connectors) - The 14-pin connector splits into an 8-pin connector and a 6-pin connector |
| RG5-7123-000CN |
Cable - Grounding cable assembly |
| RG5-7126-000CN |
Cable - Cable assembly (two 5-pin connectors) |
| RG5-7128-000CN |
Cable - Cable assembly (four 3-pin connectors) |
| RG5-7129-000CN |
Cable - Cable assembly (two connectors and two spade lugs) |
| RG5-7130-000CN |
Cable - High voltage cable assembly |
| RG5-7138-000CN |
Cable - Cable assembly for HP Color LaserJet 2820 Series |
| RG5-7139-000CN |
Cable - Cable assembly for HP Color LaserJet 2500 Series |
| RG5-7144-000CN |
Cable - Cable assembly (with seven connectors) |
| RG5-7145-000CN |
Cable - Front cable assembly (six connectors) |
| RG5-7146-000CN |
Cable - High voltage cable assembly (two 15-pin connectors and two 14-pin connectors) |
| RG5-7149-000CN |
Cable - Connector assembly - Includes the 14-pin (F) interface connector and cable assembly |
| RG5-7161-000CN |
Cable - Cable assembly (two 3-pin connectors and a spad lug) |
| RH2-5524-000CN |
Cable - Flat flexible cable (FFC) assembly - Connects between the formatter assembly (J1001) and the DC controller board (J101) |
| RG5-6910-080CN |
Carousel - Carousel (Rotary) assembly - Includes the carousel assembly, the support assembly, end plates, drive gears and shaft, sensors, and cables |
| C9700-67901 |
Cartridge - HP Color LaserJet smart Black print cartridge - Will print approximately 5,000 pages at 5% coverage |
| C9700-67901 |
Cartridge - HP Color LaserJet smart Black print cartridge - Will print approximately 5,000 pages at 5% coverage |
| C9700A |
Cartridge - HP Color LaserJet smart Black print cartridge - Will print approximately 5,000 pages at 5% coverage |
| C9701-67901 |
Cartridge - HP Color LaserJet smart Cyan print cartridge - Will print approximately 5,000 pages at 5% coverage |
| C9701-67901 |
Cartridge - HP Color LaserJet smart Cyan print cartridge - Will print approximately 5,000 pages at 5% coverage |
| C9701A |
Cartridge - HP Color LaserJet smart Cyan print cartridge - Will print approximately 5,000 pages at 5% coverage |
| C9702-67901 |
Cartridge - HP Color LaserJet smart Yellow print cartridge - Will print approximately 5,000 pages at 5% coverage |
| C9702-67901 |
Cartridge - HP Color LaserJet smart Yellow print cartridge - Will print approximately 5,000 pages at 5% coverage |
| C9702A |
Cartridge - HP Color LaserJet smart Yellow print cartridge - Will print approximately 5,000 pages at 5% coverage |
| C9703-67901 |
Cartridge - HP Color LaserJet smart Magenta print cartridge - Will print approximately 5,000 pages at 5% coverage |
| C9703-67901 |
Cartridge - HP Color LaserJet smart Magenta print cartridge - Will print approximately 5,000 pages at 5% coverage |
| C9703A |
Cartridge - HP Color LaserJet smart Magenta print cartridge - Will print approximately 5,000 pages at 5% coverage |
| 5090-3379 |
Cleaner - Toner cleaning cloth - Specially treated cloth for absorbing toner (1 per package) - Ideal for cleaning up toner spills |
| WT2-5056-000CN |
Clip - Cable clip - `C` shaped White plastic |
| XD2-1100-502CN |
Clip - E-ring clip for HP Color LaserJet 1500 Series |
| XD9-0136-000CN |
Clip - Retaining E-ring |
| XD9-0233-000CN |
Clip - Retaining E-ring |
| RH7-5366-000CN |
Clutch - Electromagnetic clutch assembly (24V) - Electrical clutch between the clutch drive gear and shaft |
| RH7-5389-000CN |
Clutch - Electromagnetic clutch assembly (24V) - Electrical clutch between the clutch drive gear and shaft |
| RH2-5519-000CN |
Connector - Connector assembly - For optional paper tray |
| RH2-5520-000CN |
Connector - Connector for the fusing assembly - Seven small contol pins plus three separated high current pins |
| WS1-6336-000CN |
Connector - Connector assembly - For optional bottom paper tray |
| WT2-5737-000CN |
Connector - Drawer connector - Connector located on bottom of tray assembly frame on right side, which connects tray assemblies to each other |
| RG5-6927-000CN |
Control Panel - Control panel assembly (mechanical only) - Includes the 'Rotate Carousel', 'Cancel Job' and the 'Go' buttons, plus the various indicator light pipes - All switches and LED's are on the formatter PC board |
| RB2-9916-020CN |
Cover - Cover - For the engaging motor (PM704) - Mounts on the upper left side of the rear frame assembly |
| RB3-0028-000CN |
Cover - Left side cover (Quartz Gray) - Does not include any attaching parts |
| RB3-0030-000CN |
Cover - Upper rear cover (Quartz Gray) - Mounts on the upper rear of the printer above the face-up output tray door |
| RB3-0032-000CN |
Cover - Face-down paper output L-Shaped cover ( Blue) - Serves as the rear of the tray for the face-down output tray on top of the printer |
| RB3-0052-000CN |
Cover - Gear Cover (Small Black plastic cover) - Covers the left end of the feed drive shaft |
| RB3-0102-000CN |
Cover - Front inner cover (Blue) - Mounts on the front frame above the multi-purpose input tray |
| RB3-0103-000CN |
Cover - Front lower cover (blue plastic) - Front lower strip below the multi-purpose input tray - Has recessed area for the printer logo |
| RB3-0104-000CN |
Cover - Roller cover - Covers the multipurpose paper pickup roller assembly - Mounts on the lower front of the front frame assembly |
| RB3-0106-000CN |
Cover - Left side frame/cover (Quartz Gray) plastic - Left side cover and input paper tray guide |
| RB3-0109-000CN |
Cover - Front cover for the 250 sheet paper cassette tray (Blue) plastic - Has molded in paper loading instructions and a '2' on the front |
| RB3-0120-000CN |
Cover - Solenoid cover (Steel) - For magnetic wave sheilding |
| RB3-0120-020CN |
Cover - Solenoid cover (Steel) - For magnetic wave sheilding - Mounts over the solenoid on the right side of the front frame assembly |
| RB3-0165-000CN |
Cover - Top inner cover (black plastic) - Covers the back half of the pressure roller arms and springs |
| RB3-0166-000CN |
Cover - Bottom inner cover (Black) plastic - One covers the paper feed sensor in the center and the other covers sensor wires toward the right side |
| RB3-0282-000CN |
Cover - Inner cover - Covers the small interconnecting PC board |
| RB3-0283-000CN |
Cover - Inner cover - Covers the bottom of the connector that interconnects the input tray base to the printer |
| RG5-6900-000CN |
Cover - Top cover assembly (blue plastic) - Includes the molded-in face-down output tray and the lift-up top cover door assembly |
| RG5-6902-000CN |
Cover - Left side cover assembly (Quartz Gray) plastic - Includes the power switch button, rod and spring (The power switch is located on the low voltage power supply board) |
| RG5-6919-000CN |
Cover - Right side frame/cover assembly (Quartz Gray) plastic - Includes the right side cover and paper tray guide, the cassette retainer spring, tray 3 connector, printer interface connector, and rubber feet |
| RG5-6953-000CN |
Cover - Right side cover assembly (Quartz Gray) plastic - Includes the DIMM memory door |
| RB3-0108-000CN |
Cross Brace - Metal support cross-brace - Mounts on the top rear of the left and right support frame/cover assemblies |
| RB3-0108-020CN |
Cross Brace - Metal support cross-brace - Mounts on the top rear of the left and right support frame/cover assemblies - For the base on the 250-sheet input tray assembly |
| RB2-6248-000CN |
Damper - Damper assembly (Gray plastic piece with small 13-tooth gear on it) |
| RB3-0033-000CN |
Door - Memory access door (Quartz Gray perforated plastic) - Allows access to the printer memory slots - Mounts on the right side cover |
| RF5-4007-000CN |
Door - Top cover door (blue plastic) - For accessing the toner cartridges and the imaging drum/transfer assembly - Mounts to the top cover frame |
| RG5-6911-000CN |
Drive Assembly - Rotary drive assembly - Includes the carousel rotating motor (DCM703), toner cartridge drive motor (PM705), developing rotary stopper solenoid (SL93), bracket, and gears |
| C9704-67901 |
Drum - Imaging drum/transfer assembly cartridge - Inserts into printer through the top door - Life expectancy is 20,000 pages for black print ONLY, 5,000 pages for color (Typical combined life is approximately 6,000 to 8,000 pages) |
| C9704A |
Drum - Imaging drum/transfer assembly cartridge - Inserts into printer through the top door - Life expectancy is 20,000 pages for black print only, 5,000 pages for color (Typical combined life is approximately 6,000 to 8,000 pages) |
| RH7-1537-000CN |
Fan - Cooling fan (Panaflo Model FBA08T24H - 80mm X 80mm X 15mm high, DC brushless, 24V DC, 190mA) |
| RH7-1630-000CN |
Fan - Cooling fan (Panaflo Model FBA08T24H - 80mm X 80mm X 15mm high, DC brushless, 24V DC, 190mA) |
| RB2-9925-000CN |
Flag - Sensor arm and flag - Activates the photosensor (Does NOT include the roller) |
| RB3-0111-000CN |
Flag - Paper flag - Plastic rod with paper sensing flag on one end and sensor activator flag on the other |
| RB3-0130-000CN |
Flag - Shaft mounted sensor flag (black plastic) |
| RB3-0132-000CN |
Flag - Mechanical sensor flag (black plastic) |
| RB3-0135-000CN |
Flag - Test print flag (Black lever) |
| RB2-6297-000CN |
Foot - Rubber foot - Square self-adhesive rubber foot |
| RB3-0105-020CN |
Frame - Center support frame (black plastic) - Support structure for the paper pickup roller, feed roller, and paper sensors |
| RG5-6903-000CN |
Fuser Assembly - Fuser Assembly (For 110V to 127V operation) - Bonds the toner to the paper with heat |
| RG5-6913-000CN |
Fuser Assembly - Fuser Assembly (For 220V to 240V operation) - Bonds the toner to the paper with heat |
| RM1-3525-000CN |
Fuser Assembly - Fusing assembly (For 220V to 240V operation) - Bonds the toner to the paper with heat - Slides in and locks in lower rear of printer |
| RB3-0022-000CN |
Gear - 22 tooth gear (Black plastic) - Small gear with diagonally cut teeth |
| RB3-0091-000CN |
Gear - 16 tooth gear (Black plastic) - Gear with large stop tooth and shaft lock tab |
| RB3-0092-000CN |
Gear - 15 tooth gear with drive shaft (Black plastic) |
| RG5-6938-000CN |
Gear - Gear assembly - Metal plate with two White plastic gears attached |
| RS7-0418-000CN |
Gear - 26 tooth gear (Black plastic) - Has 1/8th portion of gear cut away |
| RS7-0424-000CN |
Gear - Dual gear - 20 tooth / 40 tooth |
| RS7-0425-000CN |
Gear - 30 tooth gear (White plastic) |
| RS7-0426-000CN |
Gear - Dual gear - 26 tooth / 50 tooth (White plastic) |
| RS7-0428-000CN |
Gear - 30 tooth gear (White plastic) |
| RS7-0429-000CN |
Gear - 26 tooth gear (White plastic) - Has recess for shaft drive pin |
| RS7-0430-000CN |
Gear - 26 tooth gear - White gear with 1/8th portion of gear cut away and pin for spring tensioning |
| RS7-0431-000CN |
Gear - 15 tooth Gear (white plastic) |
| RS7-0435-000CN |
Gear - Dual gear - 32 tooth / 37 tooth (White plastic) |
| RS7-0436-000CN |
Gear - Dual gear - 37 tooth / 43 tooth (White plastic) |
| RS7-0437-000CN |
Gear - 51 tooth gear (White plastic) |
| RG5-6938-030CN |
Gear Assembly - Gear assembly - Metal plate with two White plastic gears attached |
| RB2-9942-000CN |
Ground - Grounding plate - Provides grounding for the top-of-page sensor and shielding for the density sensor boards |
| RB3-0119-000CN |
Ground - Grounding plate |
| RB3-0137-000CN |
Ground - Grounding plate |
| RB2-9903-000CN |
Guide - Cable guide (Quartz Gray plastic) |
| RB2-9912-000CN |
Guide - Top output bin guide - Small curved ribbed black plastic piece |
| RB2-9954-000CN |
Guide - Left paper feed guide (small Black plastic arm) |
| RB2-9955-000CN |
Guide - Right paper feed guide (small Black plastic arm) |
| RF5-4049-000CN |
Guide - Entrance guide assembly - Angled metal guide between the registration roller and the transfer roller |
| RG5-6929-000CN |
Guide - Separation guide assembly - Includes the plastic guide, label, and the two small spring loaded rollers |
| RG5-6930-000CN |
Guide - Lower separation guide assembly - Includes the guide bracket, paper output sensor (PS1) and flag, exit drive shaft with two rubber rollers, shaft gear, and idler gear |
| RG5-6935-000CN |
Guide - Left cartridge guide assembly |
| RG5-6935-020CN |
Guide - Left cartridge guide assembly |
| RG5-6951-000CN |
Guide - Paper guide assembly - Paper width adjustable guide assembly for the multi-purpose front input tray (tray 1) |
| RB2-3041-000CN |
Hinge - Tray hinge - For the left side of the multi-purpose front input tray (tray one) |
| RB2-3042-000CN |
Hinge - Tray hinge - For the right side of the multi-purpose front input tray (tray one) |
| RB2-6405-000CN |
Hinge - Tray hinge - For the left side of the multi-purpose front input tray (Tray 1) |
| RB2-6406-000CN |
Hinge - Tray hinge - For the right side of the multi-purpose front input tray (Tray 1) |
| RB2-9924-000CN |
Holder - Sensor assembly mounting holder |
| RB3-0006-000CN |
Holder - Holder - Housing for the fusing connector assembly |
| RB3-0023-000CN |
Holder - Interlock switch holder (Quartz Gray plastic) - Does NOT include the micro-switch |
| RB1-2190-000CN |
Hook - Pickup roller spring hook |
| RB3-0007-000CN |
Insulator - Insulating sheet (Transparent plastic) |
| RB3-0056-000CN |
Insulator - Insulating sheet (Transparent plastic) |
| RS6-8662-000CN |
Label - Label for Color LaserJet 2500 Series, Color LaserJet 1500 Series, Color LaserJet 2550 Series |
| RG5-6880-000CN |
Laser Scanner - Laser/scanner assembly |
| RG5-6890-030CN |
Laser Scanner - Laser/scanner assembly |
| RB3-0178-000CN |
Lever - Right side lock release lever |
| RB3-0179-000CN |
Lever - Left side lock release lever |
| C9706-90926 |
Manual - Manual for Color LaserJet 2500 Series |
| C7845A |
Memory - 32MB, 100-pin SDRAM DIMM memory module |
| C7846A |
Memory - 64MB SDRAM - 100MHz synchronous DRAM - DIMM package |
| C9121A |
Memory - 128MB, 100-pin SDRAM DIMM memory module |
| Q7707AX |
Memory - 32MB, 100-pin SDRAM DIMM memory module |
| Q7708AX |
Memory - 64MB SDRAM - 100MHz synchronous DRAM - DIMM package |
| Q7709AX |
Memory - 133 MHz 128MB, 100-pin SDRAM DIMM memory module Synchronous DRAM DIMM |
| RF5-4010-000CN |
Motor - Main motor assembly - Large motor mounted on a controller PC board |
| RF5-4010-020CN |
Motor - Main motor assembly - Large motor mounted on a controller PC board - Mounts on the inside of the metal right side frame assembly |
| RG5-6958-000CN |
Motor - Rotary motor assembly |
| RH7-1533-000CN |
Motor - Stepping motor - 24V DC |
| RH7-1535-000CN |
Motor - Stepping motor (24V) |
| RH7-1625-000CN |
Motor - Stepping motor - 24VDC |
| RH7-1629-000CN |
Motor - Stepping motor - 24V DC |
| RB2-9960-000CN |
Pad - Separation pad assembly - Includes the gray plastic frame with the rubber insert strip - For the cassette on the 250-sheet and 500-sheet input tray assemblies - Mounts in the paper cassette tray assembly Replaced by RF5-4258-020CN |
| RF5-4012-000CN |
Pad - Separation pad assembly - Includes the separation pad, holder and spring |
| RF5-4047-000CN |
Pad - Light blocking pad assembly - Black plastic frame with soft rubber gasket and stiff conductive Mylar piece (grounded) |
| RF5-4258-000CN |
Pad - Separation pad assembly - Includes the gray plastic frame with the rubber insert strip |
| RF5-4258-020CN |
Pad - Separation pad assembly - Includes the gray plastic frame with the rubber insert strip - For the cassette on the 250-sheet and 500-sheet input tray assemblies - Mounts in the paper cassette tray assembly. |
| 5851-1468 |
Paper - LaserJet printer family paper specification guide |
| Q1298A |
Paper - LaserJet Satin finish tough paper - A size (8.5 x 11-inches) - Will not tear and will withstand outdoor weather conditions - Can print on both sides |
| Q1298B |
Paper - LaserJet Satin finish tough paper - A4 size (21.0cm x 29.7cm) - Will not tear and will withstand outdoor weather conditions - Can print on both sides - 50 sheets per box |
| C9145-67901 |
PC Board - Formatter board assembly - Includes the formatter board and all the metal cage covers |
| C9145-69001 |
PC Board - Formatter board assembly - Includes the formatter board and all the metal cage covers |
| C9705-69003 |
PC Board - DC controller board - Mounts on the left side of the printer (Behind the formatter board assembly) |
| RG5-6959-060CN |
PC Board - DC controller board |
| RG5-6964-000CN |
PC Board - Carousel position and toner level photoelectric sensor PC board - L Shaped PC board with the two sensors |
| RG5-6965-000CN |
PC Board - Waste toner sensor PC board - Small board with an LED and photoelectric sensor - Monitors the level of the excess toner deposited in the imaging drum/transfer assembly |
| RG5-6967-000CN |
PC Board - Registration sensor PC Board - Small board with flag activated photosensor |
| RG5-6968-000CN |
PC Board - Interconnecting feed drive PC board |
| RG5-7609-000CN |
PC Board - Carousel position and toner level photoelectric sensor PC board - `L` Shaped PC board with the two sensors |
| RG5-7612-000CN |
PC Board - Top of page photoelectric sensor PC board - Includes the photoelectric top of page sensor and the print engine test switch |
| RG5-7613-000CN |
PC Board - Registration sensor PC Board - Small board with flag activated photosensor |
| RH7-7146-000CN |
PC Board - Density photoelectric sensor PC board |
| RH7-7158-000CN |
PC Board - Density photoelectric sensor PC board |
| WG8-5382-000CN |
PC Board - Sensor PC board - Small board with flag activated photosensor |
| WG8-5593-000CN |
PC Board - Sensor PC board - Small board with flag activated photosensor |
| WG8-5836-000CN |
PC Board - PHOTOINTERRUPTER Stapler Stacker |
| J3110A |
PC Board Interface - Ethernet 10Base-T (RJ-45) EIO network GENUINE HP JETDIRECT 600N internal print server PC board |
| J3111A |
PC Board Interface - Ethernet 10Base-T/10Base2 and LocalTalk (RJ-45, BNC, LocalTalk) EIO network PCA |
| J4135A |
PC Board Interface - JetDirect connectivity card - Has one USB port, one serial (DB9) port, and one LocalTalk port - Plugs in one of the EIO slots on selected DesignJet and LaserJet printers |
| J4167A |
PC Board Interface - JetDirect 610N token ring LAN interface board - DB-9 and RJ-45 connectors |
| J6058A |
PC Board Interface - HP JetDirect 680N internal wireless IEEE-802.11b (Wi-Fi) print server - Plugs into peripheral EIO slot |
| RB2-9916-000CN |
Plate - Mounting/grounding plate |
| RB3-0010-030CN |
Plate - Feed plate - Center metal plate with slots that the ribs on the middle frame assembly go through |
| RB3-0057-000CN |
Plate - Transfer slide plate - Small 'U' shaped metal insert plates |
| RB3-0065-000CN |
Plate - Contact plate - copper clad metal spring - Holds the left end of the small 500 Meg-ohm resistor |
| RB3-0066-000CN |
Plate - Contact plate - copper clad metal spring - Holds the right end of the small 500 Meg-ohm resistor |
| RB3-0286-000CN |
Plate - Contact plate for HP Color LaserJet 2500 Seriess |
| 8120-6800 |
Power Cord - Power cord (Flint Gray) - 3-wire, 16 AWG, 2.3m (7.5ft) long - Has straight (F) C13 receptacle (for 240V in Israel) |
| 8120-6809 |
Power Cord - Power cord (Dove Gray) - 2.3m (7.5ft) long - Has straight (F) receptacle (For 240V operation in the U.K., Hong Kong, Singapore, Malaysia) |
| 8120-6810 |
Power Cord - Power cord (Flint Gray) - 2.3m (7.5ft) long - Has straight (F) receptacle (For 240V operation in Australia, New Zealand) |
| 8120-6811 |
Power Cord - Power cord (Flint Gray) - 17 AWG, 2.3m (7.5ft) long - Has straight (F) C13 receptacle (for 220V in Europe, Saudi Arabia, South Africa, India, and Korea) |
| 8120-6812 |
Power Cord - Power cord (Flint Gray) - 18 AWG, three conductor, 2.3m (7.5ft) long - Has straight (F) C13 receptacle (For 120VAC in the United States, Canada, Mexico, Philippines, and Taiwan) |
| 8120-6813 |
Power Cord - Power cord (Dove Gray) - Three Conductor, 2.3M (7.5ft) long - Has straight (F) C13 receptacle (For 240VAC in the United Kingdom, Hong Kong, Singapore, Malaysia) |
| 8120-6814 |
Power Cord - Power cord (Flint Gray) - 17 AWG, three conductor, 2.3m (7.5ft) long - Has straight (F) C13 receptacle (For 220VAC in Denmark) |
| 8120-6815 |
Power Cord - Power cord (Flint Gray) - 17 AWG, three conductor, 2.3m (7.5ft) long - Has straight (F) C13 receptacle (For 220VAC in Switzerland) |
| RG5-6960-000CN |
Power Supply - High voltage power supply board (HVT) assembly - Has contacts for the eight high voltage springs in the printer |
| RG5-7124-000CN |
Power Supply - Sub-high voltage board - Small auxillary PC board |
| RG5-7616-000CN |
Power Supply - Sub-high voltage board - Small auxillary PC board |
| RH3-2241-000CN |
Power Supply - Low voltage power supply - For 110V to 127V AC operation - Includes the AC power input connector and power switch |
| RH3-2243-000CN |
Power Supply - Low voltage power supply - For 220V to 240V AC operation - Includes the AC power input connector and power switch |
| RH3-2252-000CN |
Power Supply - Low voltage power supply - For 110V to 127V AC operation - Includes the AC power input connector and power switch |
| RG5-6943-000CN |
Pressure Assembly - Carousel pressure (support) assembly - Includes the main rear support, E-label reader assembly, engaging sensor, and the engaging rod shaft |
| RG5-6943-020CN |
Pressure Assembly - Carousel pressure (support) assembly - Includes the main rear support, E-label reader assembly, engaging sensor, and the engaging rod shaft - Primary support structure for the toner cartridge carousel |
| J6057-69001 |
Print Server - JetDirect 615N internal print server LAN interface board - 10Base-T and 100Base-TX - Plugs into peripheral EIO slot, has RJ-45 connector. |
| J6057-69011 |
Print Server - JetDirect 615N internal print server LAN interface board - 10Base-T and 100Base-TX - Plugs into peripheral EIO slot, has RJ-45 connector. |
| J7934-61011 |
Print Server - JetDirect 620N Ethernet Print Server, internal print server LAN interface board - 10Base-T and 100Base-TX - Plugs into peripheral EIO slot, has RJ-45 connector. |
| J7934-69001 |
Print Server - JetDirect 620N Ethernet Print Server, internal print server LAN interface board - 10Base-T and 100Base-TX - Plugs into peripheral EIO slot, has RJ-45 connector. |
| J7934-69011 |
Print Server - JetDirect 620n internal print server - 10BaseT and 100BaseTX LAN interface board - Plugs into peripheral EIO slot - Has an RJ-45 connector;Click to order the functional equivalent: J7934-69021 |
| RB3-0061-000CN |
Pulley - Pulley roller (accommodates three feed belts) - Small black roller approximately 3.49cm (1-3/4 inches) long with three ball type pulleys |
| RB3-0067-000CN |
Pulley - Pulley roller (accommodates one feed belt) - Small black roller approximately 1.59cm (5/8 inch) long with one ball type pulley |
| RB3-0090-000CN |
Rack Slide - Rack slide - White plastic piece with gear teeth layed out in rack form on both sides |
| RG5-6956-000CN |
Reader - E-label reader (contact board ONLY) - Connects the cartridge nonvoliatile memory to the DC controller board |
| RG5-6957-000CN |
Reader - E-label reader assembly - Connects cartridge nonvoliatile memory to the DC controller board |
| RG5-7131-000CN |
Reader - E-label reader (contact board ONLY) - Connects the cartridge nonvoliatile memory to the DC controller board |
| RG5-7132-000CN |
Reader - E-label reader assembly - Connects cartridge nonvoliatile memory to the DC controller board |
| RG5-6939-000CN |
Registration - Registration roller assembly - Includes the roller, bushings, mounting plate, paper sensor, and the sensor flag |
| C9707A-Repair_LaserJet |
Repair Service - Ship your product to us for a small diagnostic fee; and a professional service job. We will contact you with repair total and your diagnostic fee will be waived if unit is repaired. Service warranty is 30days labor and 90days for parts. Extended warranty option is available. |
| RB3-0037-000CN |
Rod - Power switch rod - Goes between the power button and the power switch on the low voltage power supply board |
| RB2-2892-000CN |
Roller - Guide roller (Free spinning white plastic roller) - Mounts on the paper pickup drive shaft on each side of the pickup 'D' shaped roller |
| RB2-7195-000CN |
Roller - Sensor flag roller (small White plastic roller) |
| RB2-9908-000CN |
Roller - Pressure roller (small Black hard plastic disk shaped roller) |
| RB2-9909-000CN |
Roller - Pressure roller (small Black hard plastic 'solid' roller) |
| RB3-0012-000CN |
Roller - Belt roller - Small oval shaped roller approximately 1-3/4 inches long |
| RB3-0129-000CN |
Roller - Feed roller assembly - Includes the metal shaft and two small rubber rollers |
| RB3-0129-020CN |
Roller - Feed roller assembly - Includes the metal shaft and two small rubber rollers - Feeds paper from the paper cassette (or tray three below) into the printer - Mounts on the top of the center frame in the base on the 250-sheet input tray assembly |
| RB3-0160-000CN |
Roller - Paper pickup roller ('D' shaped) |
| RB3-0161-000CN |
Roller - Paper pickup roller assembly - Includes the 'D' shaped rubber roller on a plastic shaft |
| RF5-4035-000CN |
Roller - Pressure roller and arm assembly - Includes the small white roller, the holding arm, and roller scraper |
| RF5-4040-020CN |
Roller - Transfer roller assembly - Long black foam type roller - Transfers static charge to paper Part RF5-4040-000CN is no longer supplied. Please order the replacement, RF5-4040-020CN |
| RG5-6897-020CN |
Roller - Upper top bin output roller assembly - Includes the shaft with four rubber rollers, two bushing/shaft retainers, two anti-reversing flaps, and the drive gear |
| RG5-6936-000CN |
Roller - Lower top bin output roller assembly - Includes the shaft with four rubber rollers, two bushing/shaft retainers, and the drive gear |
| RG5-6939-020CN |
Roller - Registration roller assembly - Includes the roller, bushings, mounting plate, paper sensor, and the sensor flag |
| RG5-6952-000CN |
Roller - Paper pickup roller assembly - Includes the shaft, guide assembly cams, the D-shaped roller, and roller retainers - Picks paper from the multipurpose front input tray (tray 1) |
| RG5-6952-020CN |
Roller - Paper pickup roller assembly - Includes the shaft, guide assembly cams, the D-shaped roller, and roller retainers - Picks paper from the multipurpose front input tray (tray 1) - Mounts in the lower portion of the front frame assembly |
| C9707A-Manual_Color |
Service Manual - Printer Service Manual - Includes troubleshooting, error messages, paper jams, parts and parts diagrams. |
| RB2-4933-000CN |
Shaft - Lock release shaft - Small shaft with locking tab - Does NOT include the lock release lever |
| RB3-0011-000CN |
Shaft - Feed drive shaft - Long shaft with eight feed belt ball type pulleys and one ribbed feed guide drive belt pulley |
| RB3-0060-020CN |
Shaft - Idler gear shaft - Short metal rod |
| RB2-9932-000CN |
Shield - RFI shield - Parallel wire form mounted over the fan |
| RB3-0136-020CN |
Shield - Solenoid cover/magnetic shield |
| RG5-6940-050CN |
Shutter - Registration shutter assembly - Includes the metal roller, mounting frame, grounding springs, and the dual coupling gear |
| RG5-6932-060CN |
Sideplate - Right side plate assembly - Includes the front half of the metal frame assembly, gears, imaging drum/transfer assembly drive cams, cover engaging mechanism, roller engaging clutch (CL2), and main drive motor (DCM701) |
| RG5-6932-070CN |
Sideplate - Right side plate assembly - Includes the front half of the metal frame assembly, gears, imaging drum/transfer assembly drive cams, cover engaging mechanism, roller engaging clutch (CL2), and main drive motor (DCM701) - Mounts on the right side |
| RG5-6934-000CN |
Sideplate - Right rear side plate assembly - Includes the rear half of the metal right side plate, the fusing assembly drive motor and the three associated gears |
| RG5-6942-000CN |
Sideplate - Left side carousel plate assembly - End plate under the rotational toner cartridge carousel - Includes all of the high voltage contacts for the toner cartridges |
| RG5-6942-030CN |
Sideplate - Left side carousel plate assembly - End plate under the rotational toner cartridge carousel - Includes all of the high voltage contacts for the toner cartridges - Mounts on the metal carousel support frame |
| RH7-5337-000CN |
Solenoid - Solenoid assembly |
| RH7-5340-000CN |
Solenoid - Solenoid assembly |
| RH7-5341-000CN |
Solenoid - Solenoid assembly |
| RH7-5347-000CN |
Solenoid - Solenoid assembly |
| RH7-5384-000CN |
Solenoid - Solenoid assembly |
| RB2-2843-000CN |
Spring - Torsion spring - Provides a small amount of back pressure for the paper sensor flag. (Flag sold separately RB2-6264-000CN). |
| RB2-9905-000CN |
Spring - Torsion spring for HP Color LaserJet 2500 Series |
| RB2-9906-000CN |
Spring - Torsion spring for HP Color LaserJet 1500 Series |
| RB2-9952-000CN |
Spring - Tray 1 flag spring - Provides torsion for the tray 1 paper sensor flag |
| RB3-0015-000CN |
Spring - Compression spring |
| RB3-0016-000CN |
Spring - Electrical contact spring - Spring steel wire with compression springs formed on both ends |
| RB3-0042-000CN |
Spring - Electrical contact spring |
| RB3-0043-000CN |
Spring - Electrical contact spring |
| RB3-0044-000CN |
Spring - Electrical contact spring |
| RB3-0045-000CN |
Spring - Electrical contact spring |
| RB3-0046-000CN |
Spring - Electrical contact spring |
| RB3-0047-000CN |
Spring - Electrical contact spring |
| RB3-0048-000CN |
Spring - Electrical contact spring |
| RB3-0121-000CN |
Spring - Right retaining spring - Helps to secure and ground the imaging drum/transfer assembly in the printer |
| RB3-0122-000CN |
Spring - Left retaining spring - Helps to secure the imaging drum/transfer assembly in the printer |
| RS6-2025-000CN |
Spring - Tensioning spring |
| RS6-2030-000CN |
Spring - Tension spring for HP Color LaserJet 1500 Series |
| RS6-2759-000CN |
Spring - Compression spring |
| RS6-2760-000CN |
Spring - Compression spring |
| RS6-2766-000CN |
Spring - Tension spring for HP Color LaserJet 1500 Series |
| RB3-0009-000CN |
Static Dissipater - Static eliminator ground plate - Right angled metal piece with small teeth on top edge |
| RB2-3019-000CN |
Stop - Shipping stopper (bright orange plastic) - Helps to prevent damage to the paper tray by restricting the movement of the lift plate (Removed for normal use) |
| RB2-9963-000CN |
Support - Separation pad support - Pivoting 'L' shaped metal support frame (Does NOT include the separation pad assembly) |
| RB3-0062-000CN |
Support - PC board support (Black plastic holder) |
| RG5-6907-030CN |
Support - Laser/scanner support assembly (sheet metal plate) |
| RH7-6051-000CN |
Switch - Microswitch with lever activator |
| RH7-7149-000CN |
Thermistor - Thermistor for HP Color LaserJet 2500 Series |
| RH7-7159-000CN |
Thermistor - Thermistor for HP Color LaserJet 2820 Series |
| RB3-0019-000CN |
Tray - Toner catch tray (curved Black plastic piece) - Holds residual toner from photosensitive drum |
| RB3-0176-000CN |
Tray - Face-Up output tray door (ONLY) |
| RG5-6931-000CN |
Tray - Face-up output tray assembly - Includes the pull-down door and fusing assembly locking bracket (Does NOT include the lock releases) |
| C9699A |
Tray Assembly - Optional 500 sheet paper input tray - Includes tray base which attaches to tray 2, and the slide out paper tray - Accommodates 216mm x 279mm (8.5 x 11 inches) or 210mm x 279mm (8.3 x 11.7 inches) media - Optional 250 sheet tray must be installed first |
| RG5-6914-040CN |
Tray Assembly - 250 sheet paper tray assembly - Pull out cassette that the paper is loaded into - Does NOT include the paper feed base assembly |
| RG5-6937-000CN |
Tray Assembly - Multi-purpose front input tray assembly (tray-1) - Includes the front cover piece, pull-out paper support, and the flip-out extender |
Techical Help
View service parts