| CH971-63114 |
Accessory - High Density Polyethylene (HDPE) funnel - 32Oz capacity - Facilitates emptying ShopVac waste ink into waste ink bottle |
| CH971-91490 |
Bar - Y-axis alignment bar - Includes fine-thread screws for adjusting the Y-axis alignment of the printheads - Located in front of the printheads |
| CH971-91640 |
Bearing - Grit roll bearings kit - Includes 12 units |
| CH971-90710 |
Belt - Carriage drive timing belt - Located between the carriage drive motor and the carriage drive shaft |
| CH971-91530 |
Belt - Drive belt - Used for the service station wiper motion |
| CH154-67015 |
Bottle - Flush bottle - Squeeze bottle with label for UV flush |
| CH971-57219 |
Bracket - Carriage drive bracket - For use with Designjet H series and Scitex FB910/FB950 printers |
| CH971-50148 |
Cable - Cable assembly - Cable between the headboard and the UV lamp - For the Scitex FB950 and the Designjet H-Series |
| CH971-50163 |
Cable - Cable harness - Goes from the OHS board to the ink pumps |
| CH971-52323 |
Cable - Cable - Used to connect the printer directly to a print server - For use without a hub |
| CH971-57303 |
Cable - Cable - Goes from the headboard to the air valve assembly |
| CH971-91589 |
Cap - Printhead cap - Used to cap a printhead port or similar luer fitting location |
| CH971-91590 |
Cap - Tube cap - Used to cap the end of the luer fitting that normally connects to the ink tube |
| CH971-91497 |
Carriage - Carriage headboard assembly - For use with the Designjet H-Series and Scitex FB950 printer |
| CH971-91502 |
Carriage - Carriage drive assembly with bracket - For use with Scitex FB950/FB950 and Designjet H series |
| CH116A |
Cartridge - HP Designjet 788 Cyan Ink |
| CH117A |
Cartridge - HP Designjet 788 Magenta Ink |
| CH118A |
Cartridge - HP Designjet 788 Yellow Ink |
| CH119-60001 |
Cartridge - Designjet 788 black ink profiler cartridge |
| CH119A |
Cartridge - HP Designjet 788 Black Ink |
| CH120-60001 |
Cartridge - Designjet 788 1-liter light cyan ink cartridge |
| CH120A |
Cartridge - HP Designjet 788 Light Cyan Ink |
| CH121-60001 |
Cartridge - HP Designjet 788 light magenta cartridge |
| CH121-60003 |
Cartridge - HP Designjet 788 light magenta cartridge |
| CH121A |
Cartridge - HP Designjet 788 Light Magenta Ink |
| CH154-67045 |
Clip - Clip assembly - Includes one unit, does not include the taller luer cap required for use with the clamp - Used on the printhead ink U-tubes - For use with Designjet H-series and Scitex FB950 |
| CH971-91001 |
Clip - Clip - Connected to the trolley and provides attachment points for the carriage drive belt on both ends |
| CH971-57327 |
Connector - Complete ink tube/filter/connectors assembly - Used with the ink boxes - For use with Scitex FB950/FB500/FB700 and Designjet H (CS 5400uv) printers |
| CH971-91509 |
Control Panel - Touch-sensitive color LCD control panel - Used on all Designjet H-series and ColorSpan 5400UV series printers |
| CQ114-67054 |
Control Panel - Touch-sensitive LCD control panel - For the Scitex FB500/FB700 printer |
| L1Q41-67084 |
Control Panel - Frm,Lcd,U |
| CH971-91634 |
Coupler - Off-Head Supply (OHS) ink coupler - Includes one coupling and the nut used to secure it on the printer - This is the quick-disconnect attachment for the ink boxes and receives the connector from the inkbox pigtail |
| CH154-67005 |
Encoder - Encoder strip actuator assembly - Includes bracket - Used in all lifting assemblies and service station - For the Scitex FB950 printer |
| CH971-90708 |
Encoder - Encoder reader assembly - Located on the back of the carriage assembly |
| CH971-91425 |
Encoder - Mylar encoder strip and foam tape - It is long enough for a 2.5m (98-inch) printer and can be trimmed down for smaller printers - Part requires you to reuse the existing aluminum bar from the old strip |
| CH154-67010 |
Fan - Cooling fan - Used on the carriage (all four locations) and the Designjet H image sensor - For use with Scitex FB950 printers only |
| CH971-91513 |
Fan - Fan assembly - Cools the electronics box in the printer |
| CH971-91596 |
Fan - UV lamp housing cooling fan - For the Scitex FB500/FB700/FB950, and Designjet H-series printers |
| CH971-91599 |
Fan - Fan assembly - Located on the top enclosure and end enclosures - For the Scitex FB500/FB700, also the Designjet H-Series |
| CH104-67020 |
Filter - Tube/filter/fitting assembly - Used between the printhead and the air manifold |
| CH108-60004 |
Filter - Large cylindrical air filter - Located on the exterior of the vacuum assembly |
| CH971-91504 |
Filter - Ink filter - 1.74-inch diameter - Can be used with any ink color - This filter is used in the OHS area of the printer - For use with Scitex FB950 and Designjet H-Series |
| CH971-91639 |
Filter - Tube/filter/fitting assembly - Used between the printhead and the air manifold |
| CH971-91644 |
Filter - Replacement filter - Includes media and mesh used inside the ShopVac, as well as related fasteners - For the Scitex FB500/FB700 printers |
| CQ114-67188 |
Filter - Replacement filter - Includes media and mesh used inside the ShopVac, as well as related fasteners - For the Scitex FB500/FB700 printers |
| CH971-91594 |
Glass Assembly - Quartz lamp glass - Inserts below the left or right lamp housing - For the FB500/FB700/FB950, also the Designjet H-Series |
| CH971-62845 |
Guide - Guide Linear Miniature |
| 0601310-012 |
Hardware - Screw Pph Sems M4 0.7 Pitch St |
| 970811 |
Hardware - Frm Mtr Carrdrv Sfemxabcdhij R |
| CH108-67016 |
Hardware - Kit Lintfree Cloth 12 Cnt |
| CH154-67043 |
Hardware - ShopVac vacuum - 8-liter capacity - Compatible with all vintages of the Scitex FB950 printer - When installing this part on some vintages, a power cable (included) must be replaced |
| CH238A |
Hardware - Kit Lintfree Cloth 12 Cnt |
| CH971-62374 |
Hardware - Tube Tygon R-3603 0.0625 Id |
| CH971-62385 |
Hardware - Tube Tygon 2075 0.25 Id 0.375 |
| CH971-62414 |
Hardware - Fitting Male Luer Lock Ring 1/ |
| CH971-62547 |
Hardware - Luer fitting (White) - 1/8-inch, male-taper - Used on the ink tubing |
| CH971-62550 |
Hardware - Luer fitting (White) - 3/32-inch, male-taper - Used on the ink tubing |
| CH971-91491 |
Hardware - Manifold assembly - Includes six valves that mounts on the rear of the carriage above the trolley |
| CH971-91531 |
Hardware - ShopVac vacuum - 8-liter capacity - Compatible with all vintages of the Scitex FB950 printer |
| CH971-91534 |
Hardware - Frm Sw Media Adv Fmxabcdhijn |
| CH971-91544 |
Hardware - Ink pump - Includes the tubing, fitting, and torx fasteners for installation |
| CH971-91598 |
Hardware - ShopVac vacuum - 8-liter capacity - Compatible with all vintages of the Scitex FB950 printer |
| CH976-00148 |
Hardware - Check valve assembly (White) - Used in the Off-Head Supply (OHS) - Color-coded for Light Cyan |
| CH976-00149 |
Hardware - Check valve assembly (Black) - Used in the Off-Head Supply (OHS) - Color-coded for Black |
| CH976-00150 |
Hardware - Check valve assembly (Red) - Used in the Off-Head Supply (OHS) - Color-coded for Magenta |
| CH976-00151 |
Hardware - Check valve assembly (Green) - Used in the Off-Head Supply (OHS) - Color-coded for Light Magenta |
| CH976-00152 |
Hardware - Check valve assembly (Blue) - Used in the Off-Head Supply (OHS) - Color-coded for Cyan |
| CH976-00153 |
Hardware - Check valve assembly (Yellow) - Used in the Off-Head Supply (OHS) - Color-coded for Yellow |
| CH980-00219 |
Hardware - Nut Hex Metric Keps M6 Blck Ro |
| CH971-90716 |
Idler - Carriage idler assembly - Located on left end of the printer - Includes various parts and instructions describing how to remove and replace the item |
| CH971-91595 |
Idler - Idler assembly - Located on service-end of the rail - For use with Scitex FB910/FB950 and the Designjet H-series |
| CH154-67044 |
Kit - Hardware kit - Includes 12 clip assemblies and 12 taller luer caps - For use with the Designjet H-series and Scitex FB950 |
| CH971-91602 |
Kit - Ink line and fittings kit - Includes 24-inch UV ink tubing and an assortment of color-coded luer fittings |
| CH154-67091 |
Lamp - UV bulb/lamp - For use with Designjet H-Series and Scitex FB950/FB500/FB700 printers |
| CH971-90854 |
Maintenance Kit - Grease kit - Used to lubricate gritroll bearings, media drive worm gear, and up/down threads of the media hold-down roller |
| 0970811 |
Motor - Carriage drive motor - For Scitex printers |
| CH971-90713 |
Motor - Media advance motor - Only includes the motor |
| CH971-90811 |
Motor - Carriage drive motor - For Scitex printers |
| CH971-91533 |
Motor - Service station wiper motor - Moves the wiper head in the Y axis - For the Scitex FB500/FB700/FB950, also the Designjet H-Series |
| CH971-91512 |
PC Board - Power distribution board - Routes inbound AC to the various printer power supplies - For the Scitex FB500/FB700, and the Designjet H-Series |
| CH971-91542 |
PC Board - Main controller board - Used for the Off-Head Supply (OHS) - Has sockets for the profilers |
| CH971-60068 |
Power Supply - Mini power supply (24VDC) - Powers the ink system vacuum pump only - For use with Scitex FB950 and Designjet H printers |
| CH971-90826 |
Power Supply - ATX power supply - Output voltage 12VDC - Located in the main electronics box |
| CH971-91083 |
Power Supply - Power supply and power plug adapter kit - Needed to implement the external auxiliary power source for IDS vacuum |
| CH971-91505 |
Power Supply - ATX power supply - Output voltage 12VDC - Located in the main electronics box |
| CH971-91507 |
Power Supply - UV power supply - For the Scitex FB500, also used in some models of the Designjet H-Series |
| CH971-91618 |
Power Supply - Ionizer power supply - For replacement of the Simco-branded ionizer-bar power supply only |
| CH104-67002 |
Pressure Assembly - Vacuum/pressure assembly - Pressure pump for the Ink Delivery System (IDS) - Located on the OHS assembly |
| CH971-91543 |
Pressure Assembly - Vacuum pressure assembly |
| CH971-91493 |
Printhead - Master printhead - Does not include any thermistors - Used on any location of the printer - For use with Scitex FB950 and any model of the Designjet H series |
| CH154-67006 |
Reader - Encoder reader board - Does not include the metal bracket - This assembly is used on all of the lifting positions - For the Scitex FB950/FB500/FB700 printer |
| CH971-91586 |
Relay - AC relay - Located in the main electronics box |
| CH105A-Repair_DesignJet |
Repair Service - Ship your product to us for a small diagnostic fee; and a professional service job. We will contact you with repair total and your diagnostic fee will be waived if unit is repaired. Service warranty is 30days labor and 90days for parts. Extended warranty option is available. |
| CH104-67001 |
Reservoir - Printhead reservoir kit - For use when there is a reservoir leak, fitting problem, or other printhead issues, where jetting is not the problem - For use with any of the piezo-printhead engines |
| CH971-57266 |
Reservoir - Vacuum reservoir - This is a portion of the ink system vacuum - For use with Designjet H series and Scitex FB950 printers |
| CH971-55394 |
Sensor - Sensor assembly - Used to vacuum pressure in the gator ink delivery system |
| CH971-60085 |
Sensor - Carriage home sensor - For use with Scitex FB950 printer |
| 0602429-002 |
Service Parts - Cbl Cm P Ethernet Cat6 3ft |
| 5064-5555 |
Service Parts - Assy pigtail OHS inkbox IC Filter |
| 507139 |
Service Parts - Order Ch971-57139 |
| 507251 |
Service Parts - Order Ch971-91604 |
| 507266 |
Service Parts - Order Ch971-57266 |
| 901488 |
Service Parts - FRM ASSY LEFT LAMP N |
| 901489 |
Service Parts - Order Ch971-91489 |
| 901491 |
Service Parts - Order Ch971-91491 |
| 901493 |
Service Parts - Order Ch971-91493 |
| 901497 |
Service Parts - Order Ch971-91497 |
| 901507 |
Service Parts - Order Ch971-91507 |
| 901509 |
Service Parts - Order Ch971-91509 |
| 901514 |
Service Parts - Order Ch971-91514 |
| 901515 |
Service Parts - Order Ch971-91515 |
| 901529 |
Service Parts - Order Ch971-91529 |
| 901536 |
Service Parts - Order Ch971-91536 |
| 901543 |
Service Parts - Order Ch971-91543 |
| 901595 |
Service Parts - Order Ch971-91595 |
| 901596 |
Service Parts - Order Ch971-91596 |
| 901598 |
Service Parts - Order Ch971-91598 |
| 901604 |
Service Parts - Order Ch971-91604 |
| 901630 |
Service Parts - Order Ch971-91630 |
| 901644 |
Service Parts - Order Cq114-67188 |
| CH104-67003 |
Service Parts - Frm N Media Drive |
| CH104-67010 |
Service Parts - Frm Table Latch N |
| CH104-67011 |
Service Parts - Frm Platen Extension N |
| CH104-67012 |
Service Parts - Frm Upper Trolley Plate N |
| CH104-67013 |
Service Parts - Frm Rail Steel Strips N |
| CH104-67014 |
Service Parts - Frm Sensor Media Out N |
| CH104-67018 |
Service Parts - Frm Assy Motherboard N |
| CH104-67019 |
Service Parts - Frm Leveling Pad N |
| CH104-67022 |
Service Parts - Frm Steel Trolley Bearings N |
| CH104-67023 |
Service Parts - Frm Air Filter Photodiode N |
| CH104-67025 |
Service Parts - Fmkh-Series,Upgrade_Kit |
| CH107-67001 |
Service Parts - Gas_Spring,Top_Cover,Q |
| CH116-60001 |
Service Parts - HP Designjet 788 Cyan ink profiler |
| CH117-60001 |
Service Parts - HP Designjet 788 Magenta ink profiler |
| CH118-60001 |
Service Parts - HP Designjet 788 Yellow ink profiler |
| CH232A |
Service Parts - HP DJ H35000/H45000 Fume Exhaust HW |
| CH971-50128 |
Service Parts - H-Series J1 Wiring Harness |
| CH971-50137 |
Service Parts - Assy Cbl Piranha Ac In Ptr |
| CH971-50138 |
Service Parts - Assy Cbl Piranha Rail Encdr On/Off Sw |
| CH971-50139 |
Service Parts - Assy Cbl Piranha Analog |
| CH971-50140 |
Service Parts - Assy Cbl Piranha Svcice Station |
| CH971-50141 |
Service Parts - H-Series J5 Wiring Harness |
| CH971-50142 |
Service Parts - H-Series J6 Wiring Harness |
| CH971-50144 |
Service Parts - H-Series J7 Wiring Harness |
| CH971-50145 |
Service Parts - H-Series J8 Wiring Harness |
| CH971-50175 |
Service Parts - Assy Cbl Piranha Press/Vac |
| CH971-50179 |
Service Parts - Assy Cbl Piranha Ac Pwr To Ebox |
| CH971-51506 |
Service Parts - Power cord - Input voltage 220 VAC, 16 amps - Plugs into a NEMA L6-20 wall receptacle (North America) |
| CH971-55457 |
Service Parts - Assy Snsr Gtr Mag Encdr Srvc Stn Index |
| CH971-56942 |
Service Parts - Brkt Service Station Piranha Lbrkt Mnt |
| CH971-56981 |
Service Parts - Assy Media Drive Piranha |
| CH971-57013 |
Service Parts - Track Roller Table Piranha 23 Rlr Black |
| CH971-57052 |
Service Parts - Brkt Carriage Piranha Igus Chain |
| CH971-57101 |
Service Parts - Encl Ohs Piranha Base |
| CH971-57103 |
Service Parts - Assy Rail Piranha |
| CH971-57125 |
Service Parts - Brkt Ptr Piranha Vertical Support Right |
| CH971-57128 |
Service Parts - Encl Printer Piranha User Top |
| CH971-57139 |
Service Parts - Assy Covers Piranha |
| CH971-57152 |
Service Parts - Brkt Ptr Piranha Vertical Support Left |
| CH971-57155 |
Service Parts - Assy Cvr Piranha Brush |
| CH971-57158 |
Service Parts - Kit Accessory Piranha |
| CH971-57251 |
Service Parts - Assy Spool Piranha Stand |
| CH971-57257 |
Service Parts - Assy Igus Piranha |
| CH971-57265 |
Service Parts - Tube Retainer Platen 5400 Igus Brkt |
| CH971-57306 |
Service Parts - Insulation Printer 5400 Front |
| CH971-57307 |
Service Parts - Insulation Printer 5400 Left |
| CH971-57308 |
Service Parts - Insulation Printer 5400 Back |
| CH971-57309 |
Service Parts - Insulation Printer 5400 Top |
| CH971-57310 |
Service Parts - Insulation Printer 5400 Right Front |
| CH971-57311 |
Service Parts - Insulation Printer 5400 Right Middle |
| CH971-57312 |
Service Parts - Insulation Printer 5400 Right Back |
| CH971-57363 |
Service Parts - Brkt Carriage Piranha Head Pcb |
| CH971-57377 |
Service Parts - Assy Slide Fence Piranha |
| CH971-57391 |
Service Parts - Assy Carriage Holddown Piranha |
| CH971-57648 |
Service Parts - Lbl Ebox Cs54xx Power+data Ports |
| CH971-57671 |
Service Parts - Assy Table Height Adjust Piranha |
| CH971-57706 |
Service Parts - Lbl Io Board Piranha |
| CH971-62360 |
Service Parts - Power cord - 3 pin, 200-250VAC, 50/60Hz, 16/20A, 2.5m (8.2ft) - Has a IEC 60309 industrial plug (Europe) |
| CH971-62585 |
Service Parts - Ftng 10-32 Unf Plug O-Rng Seal 303 Sst |
| CH971-62880 |
Service Parts - Brkt Ball 10mm 2.5 High |
| CH971-62905 |
Service Parts - Brace Table Leg Rght 13.31 Lg 0.625 Wd |
| CH971-62906 |
Service Parts - Brace Table Leg Rght 13.31 Lg 0.625 Wd |
| CH971-62939 |
Service Parts - Slide 10 Ext 46mm Ball |
| CH971-62940 |
Service Parts - Pul Tmg Dbl Flngd W/Insert 3mm 20 Grv |
| CH971-62944 |
Service Parts - Shft Sst Prec Gnd 0.375 Dia 10 Lg |
| CH971-62994 |
Service Parts - Brush Strip 2.5 Lg 0.006 Dia |
| CH971-63013 |
Service Parts - Strip Foam 0.125 Thk 0.375 Wd Rubber |
| CH971-63028 |
Service Parts - Key Hex 2.5mm Short Arm |
| CH971-63054 |
Service Parts - Wshr Shldr M3 Nylon |
| CH971-91475 |
Service Parts - Fmk Cooling_Fan Service_Side N |
| CH971-91488 |
Service Parts - Frm Assy Left Lamp N |
| CH971-91489 |
Service Parts - Frm Assy Right Lamp N |
| CH971-91496 |
Service Parts - Frm Trolley N |
| CH971-91498 |
Service Parts - Frm Ionizer N |
| CH971-91500 |
Service Parts - Frm Strp Encdr 54 N |
| CH971-91501 |
Service Parts - Frm Blt Main Carr Drv 54 N |
| CH971-91506 |
Service Parts - Frm Sply Uv Power Sngl Ch N |
| CH971-91508 |
Service Parts - Frm Cbl Uv Ctrl Igus N |
| CH971-91510 |
Service Parts - Frm Pwr Sply 24 36v Dc N |
| CH971-91511 |
Service Parts - Frm Pwr Sply Ionizer N |
| CH971-91514 |
Service Parts - Frm Assy Ebox N |
| CH971-91515 |
Service Parts - Frm Brd I/O N |
| CH971-91517 |
Service Parts - Frm Cbl Lcd Serial N |
| CH971-91518 |
Service Parts - Frm Cbl Lcd Vga N |
| CH971-91519 |
Service Parts - Frm Cbl Lcd Pwr N |
| CH971-91520 |
Service Parts - Frm Encl Usersd Bottom N |
| CH971-91521 |
Service Parts - Frm Encl Usersd Top N |
| CH971-91524 |
Service Parts - Frm Encl Srvsd Top N |
| CH971-91525 |
Service Parts - Frm Encl Srvsd Bottom N |
| CH971-91528 |
Service Parts - Frm Encl Carr Cvr N |
| CH971-91529 |
Service Parts - Frm Service Station N |
| CH971-91532 |
Service Parts - Frm Assy Wiper N |
| CH971-91535 |
Service Parts - Frm Sw Rail Lift N |
| CH971-91536 |
Service Parts - Frm Grit Roll N |
| CH971-91537 |
Service Parts - Frm Media Thk Snsr N |
| CH971-91538 |
Service Parts - Frm Assy Pinchroll N |
| CH971-91539 |
Service Parts - Frm Set 12 Pnch Rlr N |
| CH971-91540 |
Service Parts - Frm Repackaging N |
| CH971-91541 |
Service Parts - Frm Cbl Ohs Control N |
| CH971-91545 |
Service Parts - Frm Tube Sol Prs Lng N |
| CH971-91547 |
Service Parts - Frm Tube Vacuum Long N |
| CH971-91550 |
Service Parts - Frm Cbl Track Gnd N |
| CH971-91551 |
Service Parts - Frm Cbl Trackdata N |
| CH971-91552 |
Service Parts - Frm Cbl Trackpower N |
| CH971-91573 |
Service Parts - Frm Assy Input Table N |
| CH971-91574 |
Service Parts - Frm Assy Output Table N |
| CH971-91575 |
Service Parts - Frm Media Collet N |
| CH971-91587 |
Service Parts - Frm Encl Top Middle N |
| CH971-91588 |
Service Parts - Frm Blwr Platen N |
| CH971-91591 |
Service Parts - Frm Caster Stand N |
| CH971-91592 |
Service Parts - Frm Assy Ebox Oce Rohs N |
| CH971-91593 |
Service Parts - Frm Track Chain Links N |
| CH971-91604 |
Service Parts - Frm Media Spool N |
| CH971-91605 |
Service Parts - Camera assembly - For use with Scitex FB950 and the Designjet H-series |
| CH971-91606 |
Service Parts - Platen Piranha Upper |
| CH971-91607 |
Service Parts - Fmk Shim Carriage 5400 Pin Plate N |
| CH971-91608 |
Service Parts - Fmk Tape Lcd Piranha N |
| CH971-91609 |
Service Parts - Kit Brg Lower Carriage |
| CH971-91610 |
Service Parts - Frm Repackaging Universal Exchange |
| CH971-91611 |
Service Parts - Frm Pinch Roller Wheel Single N |
| CH971-91612 |
Service Parts - Frm Mtr Piranha Rail N |
| CH971-91617 |
Service Parts - Frm Ionizer Ul N |
| CH971-91619 |
Service Parts - Kit Mnt Adj Table N |
| CH971-91621 |
Service Parts - Frm Assy Carriage N |
| CH971-91627 |
Service Parts - Frm Assy Ohs 2_Color_Pump_Plate N |
| CH971-91628 |
Service Parts - Frm Assy Ohs 3 Color Pump Plate N |
| CH971-91629 |
Service Parts - Fmk Tool Bearing Carriage Install N |
| CH971-91630 |
Service Parts - Frm Assy Ebox Ul N |
| CH971-91632 |
Service Parts - Frm Lift Mtr Srv Stn N |
| CH971-91642 |
Service Parts - Frm Edge Hold Down N |
| CH971-91643 |
Service Parts - Frm Assy Input+output Tables N |
| CH971-91647 |
Service Parts - Frm Set Caster Stand N |
| CH976-00142 |
Service Parts - Frm Tube Uv Ink Long White N |
| CH976-00143 |
Service Parts - Frm Tube Uv Ink Long Black N |
| CH976-00144 |
Service Parts - Frm Tube Uv Ink Long Red N |
| CH976-00145 |
Service Parts - Frm Tube Uv Ink Long Green N |
| CH976-00146 |
Service Parts - Frm Tube Uv Ink Long Blue N |
| CH976-00147 |
Service Parts - Frm Tube Uv Ink Long Yellow N |
| VH120-60003 |
Service Parts - HP Designjet 788 Light Cyan Ink |
| CH971-91577 |
Shaft - Carriage drive shaft - Shaft is knurled to prevent pulley from slipping on the shaft - For the Scitex FB500/FB700/FB910/FB950 printer |
| CQ114-67110 |
Shaft - Carriage drive shaft - Shaft is knurled to prevent pulley from slipping on the shaft - For the Scitex FB500/FB700/FB910/FB950 printer |
| CH971-91576 |
Switch - Door switch - Used ont the cover-open detect - For use with Designjet H-series printers |
| CH971-91492 |
Thermistor - Thermistors kit - Includes two ink and one air temperature thermistor (they have been calibrated together and should be replaced together) |
| CH971-55984 |
Tool - Head height gauge tool - This go/no-go gauge is used to set the printhead height to 0.085-inches above the surface of the media |
| CH971-57693 |
Tool - Custom tool - Assists removing and installing the main drive belt connection to the carriage |
| CH971-91631 |
Tool - Service tools kit - Kit includes the head height gauge, squeeze bottle (for flush), lint-free cloths, luer caps, and the carriage belt - For use with Scitex FB950 and the Designjet H-series |
| CH971-15183 |
Transformer - Step-down transformer (220VAC to 110VAC) - Used with the 110VAC ShopVac |
| CH971-91227 |
Tube - U-tube - For use with ink between two printheads of a color |
| CH971-91499 |
Tube - Short UV ink tube - Connects to the printhead with a luer fitting and to the ink track tube with multi-colored luer fittings |
| CH971-91344 |
Vacuum - Restrictor - For use with all vacuum/pressure assemblies |
View service parts