Still delivering Printer Parts amid Covid-19 Pandemic, shop with confidence!
|
![]() |
||
HP parts available for CH154A HP Scitex FB950 Printer large format printer
CH971-62824
Accessory - Adhesive backed ruler - English metric ruler - 2.5m (98-inches) long and can be cut down for the 1.6m (64-inches) size - This is the ruler located with the N-up alignment pins
CH971-63114
Accessory - High Density Polyethylene (HDPE) funnel - 32Oz capacity - Facilitates emptying ShopVac waste ink into waste ink bottle
CH971-56881
Accessory Kit - Accessory kit for the support tables - Includes all the fasteners, casters, etc needed to assemble two tables - For use with the Scitex FB910/FB950 printers
CH109-67003
Actuator - Lift motor (actuator) - Used for all up/down component movement in the printer - This motor is used in nine locations on the printer
CQ114-67068
Actuator - Lifting actuator for the rail - For the Scitex FB500/FB700 printer
CQ114-67094
Actuator - 75mm stroke actuator assembly - This is the actuator and all associated bracketry and hardware plus the lift encoder reader and strip - Used for the input and output media hold-down rollers and the alignment bar - For the Scitex FB500/FB700/FB950 printers
CH154-50002
Bar - Ionizer bar - Includes the bar with cable only - Attaches to the input side of the rail - For use with the Scitex FB950 printer
CH971-57513
Bar - Bar media guide - This bar is lowered down to stop and square the media
CH971-91490
Bar - Y-axis alignment bar - Includes fine-thread screws for adjusting the Y-axis alignment of the printheads - Located in front of the printheads
CQ115-67012
Bar - Anti-static ionizer bar - For the Scitex FB700 printers
CH154-67003
Belt - Main carriage drive belt (Blue) - For use with Scitex FB950 printers
CH971-90710
Belt - Carriage drive timing belt - Located between the carriage drive motor and the carriage drive shaft
CH971-91462
Belt - Media belt - Includes all the support pieces and accessories used to change the belt - For use with the Scitex FB950/FB910 printers
CH971-91530
Belt - Drive belt - Used for the service station wiper motion
CH971-91400
Blower Assembly - Belt vacuum blower assembly - Includes one blower - Used to suck down media to belt - For the FB500/FB700/FB950/FB910
CQ114-67238
Blower Assembly - Frmblwrblt Vacalt
CH154-67014
Bottle - Waste ink bottle - One gallon bottle with warning label for collection of UV liquid wastes
CH154-67015
Bottle - Flush bottle - Squeeze bottle with label for UV flush
CJ848A
Box - Electronics assembly (ebox assembly) - For use with the Scitex FB950
CH108-60008
Bracket - L-bracket and internal mechanical - Located on the on the output, user end of the printer - Includes the parts that transfer take-up motor power to the take-up spool (does not include the motor/switch assembly, the takeup drive belt, or the belt cover)
CH108-60009
Bracket - L-bracket - Located on the output, service end of the printer
CH108-60010
Bracket - L-bracket - Located on the input, user end of the printer - Holds the supply roll and inactive foam rollers
CH108-60011
Bracket - L-bracket - Located on the input, service end of the printer - Holds the supply roll and inactive foam rollers
CH971-57219
Bracket - Carriage drive bracket - For use with Designjet H series and Scitex FB910/FB950 printers
CH971-57259
Bracket - Service-end bracket - Supports the lift and press rollers in the roll-to-roll option
CH971-62665
Brush - Brass wire brush - Used to clean the ionizer bar
CQ114-67180
Brush - Ionizer brush - Used to clean the points on the anti-static ionizer bar
CH971-62205
Bumper - Polyurethane rubber bumper - 7/16-inch diameter x 13/64-inch thick round, adhesive-backed bumper - Used on some platforms on the rail at the carriage home, or as a spacer on the headboard-end of the LVDS cable (on Scitex FB500/FB700 printers only)
CH971-91398
Button - Emergency stop button - For use with Scitex FB950/FB910 printers
CH154-67009
Cable - UV lamp power cable - Cable goes from the electronics assembly to one lamp - For use with Scitex FB500/FB700/FB950
CH971-50014
Cable - Cable assembly - Braided ribbon cable from OHS board to I/O board - For the Scitex FB500/FB700/FB910/FB950 printers
CH971-50028
Cable - Cable - Goes from the three pin sabre connector on the AC distribution board to an AC receptacle
CH971-50116
Cable - Cable - Goes from the AC filter to the power distribution board
CH971-50148
Cable - Cable assembly - Cable between the headboard and the UV lamp - For the Scitex FB950 and the Designjet H-Series
CH971-50163
Cable - Cable harness - Goes from the OHS board to the ink pumps
CH971-50284
Cable - Cable - Goes from the UV power supply to the external connector for the UV lamp cable found on the top side of the electronics box
CH971-50286
Cable - Cable assembly - 2-wire cable - Ties in to the power cable for the UV lamp cable receptacle on the exterior of the electronics box
CH971-50289
Cable - Cable assembly - 2-wire cable - Ties in to the power cable for the UV lamp cable receptacle on the exterior of the electronics box
CH971-50299
Cable - Cable assembly - Goes from the power distribution board to the external receptacle for take-up motor power
CH971-50300
Cable - Internal ebox cable - Goes from the AC distribution board to the UVPS and AC relay - Has a 4-pin molex sabre connector for the AC distribution board connection
CH971-50316
Cable - Camera fans cable - Goes from the upper HDBD connector to the rear carriage fans
CH971-50322
Cable - Cable assembly - Goes from the headboard to the carriage home sensor
CH971-50354
Cable - Internal ebox cable assembly - Cable that goes from the I/O board J28 to AC relays, cooling fans, main power switch, foot pedal, and UV cable-present sensor
CH971-50364
Cable - Cable assembly - 2-wire cable - Goes from the UV power supply to the cable harness from the I/O board
CH971-50404
Cable - Cable assembly - Goes from the lower HDBD connector to the front carriage fans and color sensor fan
CH971-52323
Cable - Cable - Used to connect the printer directly to a print server - For use without a hub
CH971-55682
Cable - Cable assembly - Goes from the I/O board to the motor control board
CH971-57303
Cable - Cable - Goes from the headboard to the air valve assembly
CH971-57465
Cable - Cable - Goes from the external power receptacle for the ionizer power supply to the I/O board and power distribution board
CQ114-67051
Cable - Serial data cable - Touch-sensitive data transmission cable - Located between the LCD control panel and the I/O board
CQ114-67052
Cable - VGA cable - Located between the LCD control panel and the motherboard - For the video display
CQ114-67128
Cable - LVDS data cable - For use with the Scitex FB950 printer
CQ114-67243
Cable - Frm-Fb500/700-Igus-Data-Cable
CH971-57560
Cap - End cap sheet metal - Located on the service end of the printer - For use with the Scitex FB950 printer
CH971-91589
Cap - Printhead cap - Used to cap a printhead port or similar luer fitting location
CH971-91590
Cap - Tube cap - Used to cap the end of the luer fitting that normally connects to the ink tube
CH971-91497
Carriage - Carriage headboard assembly - For use with the Designjet H-Series and Scitex FB950 printer
CH971-91502
Carriage - Carriage drive assembly with bracket - For use with Scitex FB950/FB950 and Designjet H series
CQ114-67109
Carriage - Carriage drive assembly - Includes bracket, motor, drive shaft, timing belt, and all related fasteners - For the Scitex FB500/FB700 printer
CH971-57723
Clamp - Clamps - Does not in include the fastener - Secures the main (Blue) drive belt to the (Black) clips in the carriage
CH154-67045
Clip - Clip assembly - Includes one unit, does not include the taller luer cap required for use with the clamp - Used on the printhead ink U-tubes - For use with Designjet H-series and Scitex FB950
CH971-91001
Clip - Clip - Connected to the trolley and provides attachment points for the carriage drive belt on both ends
1500-1274
Collar - Internal clamping collar - 25mm diameter - Used on the ends of the media drive idle roller shaft - For the Scitex FB910/FB950/FB500/FB700 printers
CH971-91264
Collar - Spool-holding collar - Attaches to the stand on the left side take-up and supply postions (when facing front of printer)
CH971-91265
Collar - Spool-holding collar - attaches to the stand on the right side take-up and supply postions (when facing front of printer)
CH971-57327
Connector - Complete ink tube/filter/connectors assembly - Used with the ink boxes - For use with Scitex FB950/FB500/FB700 and Designjet H (CS 5400uv) printers
CH971-91634
Coupler - Off-Head Supply (OHS) ink coupler - Includes one coupling and the nut used to secure it on the printer - This is the quick-disconnect attachment for the ink boxes and receives the connector from the inkbox pigtail
CH154-60033
Display - LCD display assembly - For use with Scitex FB950 printers only
CH154-67038
Drive Assembly - Hard disk drive (HDD) - Used in the electronics assembly - For use with the Scitex FB950 printer
CH154-00013
Enclosure - Belt/roller enclosure - Located on the output-side of the user-end
CH154-67012
Enclosure - Window enclosure - Includes pushnuts - Replacement UV-blocking windows used only on the center output-side door - For the Scitex FB500/FB700/FB950
CH971-57557
Enclosure - Central top enclosure assembly - Includes the window material and fasteners - Located on the input side of the printer
CH971-57559
Enclosure - Full enclosure skins - For use on the user side of the printer - For use with the Scitex FB950 printer
CH971-57580
Enclosure - Central top enclosure assembly - Includes all fans, windows, light blocking skirt, and required fasteners - Located on the output side of the printer (top cover that can be opened)
CH971-57585
Enclosure - Belt/roller enclosure - Located on the user-end (input-side)
CH971-57586
Enclosure - Belt/roller enclosure - Located on the service-end (input-side)
CJ856A
Enclosure - Carriage cover enclosure - Includes the fans - For use with the Scitex FB950 printer
CH154-67005
Encoder - Encoder strip actuator assembly - Includes bracket - Used in all lifting assemblies and service station - For the Scitex FB950 printer
CH154-67040
Encoder - High-resolution on-shaft encoder - Used for media drive motion - For use with the Scitex FB950 printer
CH971-90708
Encoder - Encoder reader assembly - Located on the back of the carriage assembly
CH971-91407
Encoder - Media drive encoder - Attaches to the belt drive motor on the service end of the printer - Does not include the high-resolution encoder - For the Scitex FB500/FB700/FB950/FB910
CH971-91425
Encoder - Mylar encoder strip and foam tape - It is long enough for a 2.5m (98-inch) printer and can be trimmed down for smaller printers - Part requires you to reuse the existing aluminum bar from the old strip
CH154-67010
Fan - Cooling fan - Used on the carriage (all four locations) and the Designjet H image sensor - For use with Scitex FB950 printers only
CH971-91513
Fan - Fan assembly - Cools the electronics box in the printer
CH971-91596
Fan - UV lamp housing cooling fan - For the Scitex FB500/FB700/FB950, and Designjet H-series printers
CH971-91599
Fan - Fan assembly - Located on the top enclosure and end enclosures - For the Scitex FB500/FB700, also the Designjet H-Series
CH104-67020
Filter - Tube/filter/fitting assembly - Used between the printhead and the air manifold
CH108-60004
Filter - Large cylindrical air filter - Located on the exterior of the vacuum assembly
CH971-60050
Filter - AC filter - Located inside the electronics assemblies - For use with Scitex FB910/FB950 printers
CH971-91504
Filter - Ink filter - 1.74-inch diameter - Can be used with any ink color - This filter is used in the OHS area of the printer - For use with Scitex FB950 and Designjet H-Series
CH971-91644
Filter - Replacement filter - Includes media and mesh used inside the ShopVac, as well as related fasteners - For the Scitex FB500/FB700 printers
CQ114-67188
Filter - Replacement filter - Includes media and mesh used inside the ShopVac, as well as related fasteners - For the Scitex FB500/FB700 printers
CH971-91594
Glass Assembly - Quartz lamp glass - Inserts below the left or right lamp housing - For the FB500/FB700/FB950 also the Designjet H-Series
CH154-00020
Guard - Media belt edge guard - Located on the user side - For use with the Scitex FB950 printer
CH154-00021
Guard - Media belt edge guard - Located on the service side - For use with the Scitex FB950 printer
CH971-57318
Guard - Finger guard - Located on the service-end (input-side) over the belt on engines without the roll-to-roll option
CH971-57605
Guard - Finger guard - Includes a white media alignment fence on engines without the roll-to-roll option - Located on the user-end (input-side)
CH971-57691
Guard - Finger guard with media alignment fence (White) - Located on the user-end (input-side) engines without the roll-to-roll option
CH154-60013
Hardware - Float switch assembly - Includes brackets - Used in the service station - For the Scitex FB500/FB700/FB950 printer
CH154-67001
Hardware - Complete trolley assembly - Includes upper and lower plates - For use with Scitex FB950 printers
CH154-67013
Hardware - Light-blocking skirt - Used for the main cover - For use with Scitex FB950 printer
CH154-67034
Hardware - Track assembly - For use with the Scitex FB950 printer
CH154-67043
Hardware - ShopVac vacuum - 8-liter capacity - Compatible with all vintages of the Scitex FB950 printer - When installing this part on some vintages, a power cable (included) must be replaced
CH971-62547
Hardware - Luer fitting (White) - 1/8-inch, male-taper - Used on the ink tubing
CH971-62550
Hardware - Luer fitting (White) - 3/32-inch, male-taper - Used on the ink tubing
CH971-91414
Hardware - Side alignment fence - Attached to belt assembly
CH971-91491
Hardware - Manifold assembly - Includes six valves that mounts on the rear of the carriage above the trolley
CH971-91531
Hardware - ShopVac vacuum - 8-liter capacity - Compatible with all vintages of the Scitex FB950 printer
CH971-91544
Hardware - Ink pump - Includes the tubing, fitting, and torx fasteners for installation
CH971-91598
Hardware - ShopVac vacuum - 8-liter capacity - Compatible with all vintages of the Scitex FB950 printer
CH976-00148
Hardware - Check valve assembly (White) - Used in the Off-Head Supply (OHS) - Color-coded for Light Cyan
CH976-00149
Hardware - Check valve assembly (Black) - Used in the Off-Head Supply (OHS) - Color-coded for Black
CH976-00150
Hardware - Check valve assembly (Red) - Used in the Off-Head Supply (OHS) - Color-coded for Magenta
CH976-00151
Hardware - Check valve assembly (Green) - Used in the Off-Head Supply (OHS) - Color-coded for Light Magenta
CH976-00152
Hardware - Check valve assembly (Blue) - Used in the Off-Head Supply (OHS) - Color-coded for Cyan
CH976-00153
Hardware - Check valve assembly (Yellow) - Used in the Off-Head Supply (OHS) - Color-coded for Yellow
CJ860A
Hardware - Cabling loom (conduit and cables) - Used between the electronics assembly and devices on the service end of the printer
CJ861A
Hardware - Cabling loom (conduit and cables) - Used between the electronics assembly and devices on the user end of the printer (excluding devices in the user-end removable enclosure)
CJ862A
Hardware - Cabling loom (conduit and cables) - Used between the electronics assembly and devices in the user-end removable enclosure
CQ114-67073
Hardware - Float switch assembly - Includes brackets - Used in the service station - For the Scitex FB500/FB700/FB950 printer
CH154-60008
Holder - Carriage restraint - Includes all components - Used for shipping
CQ115-67047
Housing - Service-side lamp housing - Does not include bulb - For the Scitex FB700/FB950
CQ115-67048
Housing - User-side lamp housing - Does not include bulb - For the Scitex FB700/FB950
CH971-91595
Idler - Idler assembly - Located on service-end of the rail - For use with Scitex FB910/FB950 and the Designjet H-series
CH154-67016
Kit - Hardware kit - Includes the hose, spigot, and related hardware from service station basin to printer enclosure
CH154-67042
Kit - Hardware kit - This is the one-time field modification kit to install a complete set of six air tube assemblies with ink-blocking filter onto the carriage - For use with the Scitex FB950 printer
CH154-67044
Kit - Hardware kit - Includes 12 clip assemblies and 12 taller luer caps - For use with the Designjet H-series and Scitex FB950
CH971-91602
Kit - Ink line and fittings kit - Includes 24-inch UV ink tubing and an assortment of color-coded luer fittings
CH154-67091
Lamp - UV bulb/lamp - For use with Designjet H-Series and Scitex FB950/FB500/FB700 printers
CH109-67002
Lubricant - Oil-saturated cloth - Used for lubricating the carriage rail - For use with Scitex FB500/700/FB950, and H-Series printers
CH971-90854
Maintenance Kit - Grease kit - Used to lubricate gritroll bearings, media drive worm gear, and up/down threads of the media hold-down roller
CH154-67008
Motor - Media drive motor/reducer assembly - For the Scitex FB950/FB500/FB700 printer
CH971-90811
Motor - Carriage drive motor - For Scitex printers
CH971-91533
Motor - Service station wiper motor - Moves the wiper head in the Y axis - For the Scitex FB500/FB700/FB950, also the Designjet H-Series
CH971-91561
Motor - Takeup motor and switch assembly - Used for the roll-to-roll accessory - For the Scitex FB500/FB700/FB910/FB950
CH971-62834
Mount - Flush panel mount - Recessed plastic hand-hold as used in the enclosures - For the Scitex FB910/FB950/FB500/FB700
CH971-91405
Pad - Leveling pad - For Scitex FB500/FB700/FB950/FB910 printers
CH154-00004
Pan - Light blocking pan - Located over the OHS area - For use with the Scitex FB950 printer
CH154-67035
PC Board - Motherboard assembly - For use with the Scitex FB950 printer
CH154-67041
PC Board - Formatter - Software version 4.20 - For use with the Scitex FB950 printer
CH971-91389
PC Board - Motor driver board (motor control board) - Located in the electronics assembly - For the Scitex FB500/FB700/FB91O/FB950 printers
CH971-91450
PC Board - Power Distribution board - Regulates the 3-phase power going into the printer
CH971-91542
PC Board - Main controller board - Used for the Off-Head Supply (OHS) - Has sockets for the profilers
CJ855A
PC Board - I/O board - For use with the Scitex FB950 printer
CH971-91402
Pin - Alignment pin assembly - These pins are used to set position of multiple sheets - For the Scitex FB500/FB700/FB950/FB910
CH154-67002
Plate - Upper trolley plate assembly - For use with Scitex FB950 printers only
CH109-50001
Power Cord - 3-phase power cord - For use with plotters (Europe)
CH971-56213
Power Cord - Main AC power cord - For use with Scitex FB910/FB950 printers
CQ114-67046
Power Cord - Headboard power cord - Located in the track from the electronics assembly to the headboard - For use with the Scitex FB500/FB700/FB950
CH154-67011
Power Supply - UV power supply - For one channel of the lamp system - For use with Scitex FB950 printers
CH971-60068
Power Supply - Mini power supply (24VDC) - Powers the ink system vacuum pump only - For use with Scitex FB950 and Designjet H printers
CH971-90826
Power Supply - ATX power supply - Output voltage 12VDC - Located in the main electronics box
CH971-91083
Power Supply - Power supply and power plug adapter kit - Needed to implement the external auxiliary power source for IDS vacuum
CH971-91618
Power Supply - Ionizer power supply - For replacement of the Simco-branded ionizer-bar power supply only
CJ854A
Power Supply - Dual charge power supply - Output voltage 24/38VDC - For use with the Scitex FB950 printer
CH104-67002
Pressure Assembly - Vacuum/pressure assembly - Pressure pump for the Ink Delivery System (IDS) - Located on the OHS assembly
CH971-91543
Pressure Assembly - Vacuum pressure assembly
CH971-91493
Printhead - Master printhead - Does not include any thermistors - Used on any location of the printer - For use with Scitex FB950 and any model of the Designjet H series
CH154-67006
Reader - Encoder reader board - Does not include the metal bracket - This assembly is used on all of the lifting positions - For the Scitex FB950/FB500/FB700 printer
CH971-50021
Receptacle - External AC-input receptacle (Blue) - Includes the cable from the receptacle to the AC filter
CH971-91626
Regulator - Regulator - Used in the Vacuum Pressure (VP) assembly
CH971-91586
Relay - AC relay - Located in the main electronics box
CH104-67001
Reservoir - Printhead reservoir kit - For use when there is a reservoir leak, fitting problem, or other printhead issues, where jetting is not the problem - For use with any of the piezo-printhead engines
CH971-57266
Reservoir - Vacuum reservoir - This is a portion of the ink system vacuum - For use with Designjet H series and Scitex FB950 printers
CH154-20015
Roller - Media drive roller - Located on the output side of the engine - For use with the Scitex FB950 printer
CH154-20016
Roller - Media drive roller - Located on the output side of the engine - For use with the Scitex FB950 printer
CH971-57296
Roller - Foam-covered metal roller - Used in two places in the roll-feed supply system - For use with Scitex FB910/FB950 printers
CH971-57520
Roller - Media hold-down roller assembly - Located on both input or output sides - For use with the Scitex FB950 printer
CH971-91603
Roller - Bearing media roller
CH971-60085
Sensor - Carriage home sensor - For use with Scitex FB950 printer
CH971-62685
Sensor - Bracket height adjustment sensor - Mounting bracket for the alignment sensor that confirms that the media is straight before the pinch roller goes down
CH971-91028
Sensor - Service station sensor - This is the home sensor for the wipers
CH971-91406
Sensor - Media thickness sensor assembly - Calibrated in the factory - For the Scitex FB950/FB910/FB500/FB700 printer
CQ114-67023
Sensor - Optical media-out detection sensor - Located on the input side of the printer - Two are used on the printer, one at center and one at the user end - For the Scitex FB500/FB700/FB950 printer
CH154-67033
Service Parts - Repacking kit - Materials to repack plotter - For use with Scitex FB950 printers
CH971-91089
Service Parts - Media spool collet - 3-inch in size - Can be hand tightened and loosened around the steel media spool
CH971-91605
Service Parts - Camera assembly - For use with Scitex FB950 and the Designjet H-series
CJ857A
Service Station - Service station assembly - For use with the Scitex FB950 printer
CQ114-67110
Shaft - Carriage drive shaft - Shaft is knurled to prevent pulley from slipping on the shaft - For the Scitex FB500/FB700/FB910/FB950 printer
CH154-67031
Slider - Vertical slide - Located on the service station - If broken, this can be replaced alone without requiring replacement of the entire service station assembly
CH971-91258
Spindle - Media spool - Includes two 3-inch collets - For use with 98-inch printers
CH971-91558
Spindle - Media spool - Does not inlcude collets - For use with 98-inch printers
CH971-63071
Spring - Gas springs - Used to hold open the main cover on - For use with the Scitex FB950 printer
CH971-56880
Support - Media support table - For use with the Scitex FB910/FB950
CH154-67037
Switch - Replacement foot switch - Orange safety hood not included - For the Scitex FB700/FB950/FB910 and H-Series
CH971-91444
Switch - Switch - Configures the power distribution board for the type of 3-phase power used at the site - This switch must be set correctly before power is applied to the printer, or serious damage can occur to the printer
CH971-91469
Switch - On/Off switch - Located on the electronics assembly - For the Scitex FB500/FB700/FB950/FB910 printers
CH971-91576
Switch - Door switch - Used ont the cover-open detect - For use with Designjet H-series printers
CQ115-67002
Switch - Frm Foot Switch U
CQ115-67051
Tape - Foam tape - 175cm (69-inch) long - Located on top of the rail that cushions the track assembly (Igus) - This length is for any 2.5m (98-inch) printer, but may be cut down to shorter lengths for use on other machines
CH971-91562
Tensioner - Supply tensioner - Used on the user-input bracket, for use with the supply and take-up system - For use with Scitex FB910/FB950 printers
CH971-91492
Thermistor - Thermistors kit - Includes two ink and one air temperature thermistor (they have been calibrated together and should be replaced together)
CH971-55984
Tool - Head height gauge tool - This go/no-go gauge is used to set the printhead height to 0.085-inches above the surface of the media
CH971-57693
Tool - Custom tool - Assists removing and installing the main drive belt connection to the carriage
CH971-91572
Tool - Belt tension tool kit - Fixture used to measure tension on the media belt - Requires a dial indicator (not included) - For the Scitex FB500/FB700/FB950/FB910
CH971-91631
Tool - Service tools kit - Kit includes the head height gauge, squeeze bottle (for flush), lint-free cloths, luer caps, and the carriage belt - For use with Scitex FB950 and the Designjet H-series
CH971-15183
Transformer - Step-down transformer (220VAC to 110VAC) - Used with the 110VAC ShopVac
CJ858A
Tray - Vacuum fan tray - Includes the fans - Used for the pre-print (center) zone of the vacuum table - For use with the Scitex FB950 printer
CJ859A
Tray - Input/output vacuum fan tray - Includes the fans - Used for both the input and output zones of the vacuum table - For use with the Scitex FB950 printer
CH154-67004
Tube - U-tube assembly - For air connection between any two UV printheads
CH154-67017
Tube - Long opaque tube (White) - For ink that runs through the track assembly - Luer fittings are color-coded for the light cyan ink channel
CH154-67018
Tube - Long opaque tube (Black) - For ink that runs through the track assembly - Luer fittings color-coded for the black ink channel
CH154-67019
Tube - Long opaque tube (Red) - For ink that runs through the track assembly - Luer fittings are color-coded for the magenta ink channel
CH154-67020
Tube - Long opaque tube (Green) - For ink that runs through the track assembly - Luer fittings are color-coded for the light magenta ink channel
CH154-67021
Tube - Long opaque tube (Blue) - For ink that runs through the track assembly - Luer fittings are color-coded for the cyan ink channel
CH154-67022
Tube - Long opaque tube (Yellow) - For ink that runs through the track assembly - Luer fittings are color-coded for the yellow ink channel
CH154-67023
Tube - Ink system vacuum tube - Runs through the track assembly - For use with Scitex FB500/FB700/FB950 printers
CH154-67024
Tube - Ink system pressure tube - Runs through the track assembly - For use with FB500/FB700/FB950
CH971-91227
Tube - U-tube - For use with ink between two printheads of a color
CH971-91499
Tube - Short UV ink tube - Connects to the printhead with a luer fitting and to the ink track tube with multi-colored luer fittings
CQ114-67221
Tube - Bucket tube - 10.90-inches (27.68 cm) length hose - Includes hose clamps for attachment - Located in the service station basin (bucket) between the wiper and the baffle - For use with Scitex FB500/FB700/FB950 printers
CH971-91344
Vacuum - Restrictor - For use with all vacuum/pressure assemblies
CH154-67030
Wiper - Wiper blade - For use with the Scitex FB950 printer - This is a different material than the H-Series wiper
|
||
![]() |
|
|
Copyright © 2021 Partshere.com Privacy Policy Terms and Conditions Send us your Feedback |