| C2858-00078 |
Absorber - Absorber for HP DesignJet 650C series |
| C2858-60115 |
Bail - Bail assembly - Has star wheel assemblies attached |
| 1410-0708 |
Bearing - Sleeve bearing - Used on left end of overdrive assembly |
| 1500-0855 |
Belt - HP Designjet 600, 650C Motor Belt (Small belt).Y axis drive belt. |
| 1500-0856 |
Belt - Carriage belt for HP DesignJet 36inch size plotters. |
| 07575-40125 |
Bracket - Drive-tensioner bracket for pen carriage drive belt tensioning wedge |
| C1633-40037 |
Bracket - Right bail bracket |
| C1633-40038 |
Bracket - Left bail bracket for Hewlett Packard Designjet Plotters. |
| C1633-40064 |
Bracket - Media sensor mounting bracket |
| C1633-60029 |
Bracket - Y-drive assembly bracket |
| C2847-00051 |
Bracket - Y-tensioner bracket on left side plate |
| C2858-00007 |
Bracket - Encoder spring bracket - Located on the right side of the plotter |
| C1633-20034 |
Bushing - Bushing for reduction pulley |
| C2858-40016 |
Bushing - Carriage bushing - Supports front of carriage on slider rod /// order carriage unit C2858-60023 |
| C2858-40017 |
Bushing - Rear slider rod bushing (Spring loaded) - Slides into the rear center of the carriage assembly |
| C3195-40064 |
Bushing - Rear slider rod bushing (Spring loaded) - Slides into the rear center of the carriage assembly |
| C3195-40076 |
Bushing - Cutter bushing - Connects cutter assembly to slider rod |
| 17255D |
Cable - RS-232C serial cable - 25-pin (M) to 25-pin (F) - 1.2m (3.9ft) long |
| 17302A |
Cable - RS-232C serial cable - 25-pin (M) to 8-pin (M) DIN - 1.5m (4.9ft) long |
| 24540-80010 |
Cable - Centronics (parallel) cable - 36-pin (M) to 25-pin (M) - 2.0m (6.6ft) long |
| 24542G |
Cable - RS-232C serial cable - 25-pin (M) to 9-pin (F) - 3.0m (9.8ft) long |
| 5063-1256 |
Cable - IEEE-1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36-pin Centronics (M) connector (type B) - 2.0m (6.6ft) long |
| 5063-1257 |
Cable - IEEE 1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36-pin Centronics (M) connector (type B) - 3.0m (9.8ft) long |
| A6144-63008 |
Cable - RS-232C serial cable - 25-pin (M) to 9-pin (F) - 3.0m (9.8ft) long |
| C1633-60014 |
Cable - Cable assembly with ferrite - 18-pin (F) connector to four cables - Other connectors are two 4-pin (F), one 4-pin (M), and one 6-pin (F) - Overall length is 93cm (37.8in) |
| C2847-60019 |
Cable - Ribbon cable - 5-pin (F) connector to 5-pin (F) connector - 40.3cm (15.9in) long |
| C2858-60011 |
Cable - Cable harness assembly |
| C2858-60024 |
Cable - Carriage assembly trailing cable |
| C2913A |
Cable - RS-232C serial cable - 25-pin (M) to 25-pin (F) - 1.2m (3.9ft) long |
| C2950A |
Cable - IEEE 1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36-pin Centronics (M) connector (type B) - 2.0m (6.6ft) long |
| C2951A |
Cable - IEEE-1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36 pin Centronics (M) connector (type B) - 3.0m (9.8ft) long |
| C2990A |
Cable - IEEE 1284 Bi-Tronics parallel cable - DB-25 (M) (type A) to 36-pin (M) Centronics (type B) - 1.8m (6ft) long |
| C2991A |
Cable - IEEE 1284 Bi-Tronics parallel cable - DB-25 (M) (type A) to 36-pin (M) Centronics (type B) - 3.0m (10ft) long |
| C1633-40052 |
Cam - Bail lift cam - Activates the bail lift lever (part of the bail lift mechanism kit) |
| C2858-40043 |
Cap - Spindle end cap - Small core spacer - Removes for loading the media roll. Please order spindle assembly. |
| C3172-40006 |
Cap - Spindle end cap - Small core spacer - Removes for loading the media roll. Please order spindle assembly. |
| C3190-40076 |
Cap - Cartridge cap - Keeps cartridges from drying out when carriage is parked in service station |
| C2858-60023 |
Carriage - Pen carriage assembly - Drafting 'Head' assembly (Holds the four ink cartridges) |
| 51631M |
Cartridge - Color InkJet cut sheet paper - A0 size (84.1cm x 118.9cm) - 100 sheets per package |
| 51640A |
Cartridge - HP 40 Black InkJet Print Cartridge - Has ink level indicator - Prints approximately 1120 pages based on 5% density on a 8-inch by 10-inch print area (USA) |
| 51640AA |
Cartridge - HP Ink Crtg 40A Black AP |
| 51640AE |
Cartridge - HP 40 Black Genuine Original Hewlett Packard cartridge 40A Black EUR |
| 51640AL |
Cartridge - HP Ink Crtg 40A Black LAR |
| 51642M |
Cartridge - Cartridge for DesignJet-C1633A, DesignJet 600, DesignJet 650, DesignJet 200 E size |
| 51650C |
Cartridge - Cyan (Blue) ink cartridge - Has ink level indicator (USA) |
| 51650CA |
Cartridge - HP Ink Crtg 50C Cyan AP |
| 51650CE |
Cartridge - HP Ink Crtg 50C Cyan EUR |
| 51650CL |
Cartridge - HP Ink Crtg 50C Cyan LAR |
| 51650M |
Cartridge - Magenta (Red) ink cartridge - Has ink level indicator (USA) |
| 51650MA |
Cartridge - HP Ink Crtg 50M Magenta AP |
| 51650ME |
Cartridge - HP Ink Crtg 50M Magenta EUR |
| 51650ML |
Cartridge - HP Ink Crtg 50M Magenta LAR |
| 51650Y |
Cartridge - Yellow ink cartridge - Has ink level indicator (USA) |
| 51650YA |
Cartridge - HP Ink Crtg 50Y Yellow AP |
| 51650YE |
Cartridge - HP Ink Crtg 50Y Yellow EUR) |
| 51650YL |
Cartridge - HP Yellow Print Crtg, LAR |
| 1492-0145 |
Caster - Lockable caster assembly - Includes stem and washer |
| 07575-40013 |
Clamp - Left belt clamp - Attaches carriage belt to carriage |
| 07575-40014 |
Clamp - Right belt clamp - Attaches carriage belt to carriage |
| 1400-1021 |
Clamp - Cable clamp for HP DesignJet 650C Series |
| 9170-1533 |
Clamp - Clamp - Holds ferrite in place within electronics enclosure |
| C2847-60087 |
Control Panel - Control panel assembly - Includes ribbon cable |
| C1633-00031 |
Cover - MIO slot access cover |
| C2848-00002 |
Cover - Electronic enclosure cover |
| C2858-40044 |
Cover - Right end cover - For end of upper stand (Chassis) assembly |
| C2858-60215 |
Cover - Left end cover assembly - For end of upper stand (Chassis) |
| C4706-60084 |
Cover - Rollfeed access cover - Opens forward to allow access to paper spindle assembly - Includes cover and springs |
| C3186-00034 |
Cross Brace - Cross-brace - Brace that connects and supports the two stand legs |
| C2858-60021 |
Cutter - Cutter mechanism assembly - Auto cutter for rollfeed paper |
| C2848-60001 |
Enclosure - Enclosure - Metal structure that forms the base of the electronics enclosure assembly |
| C2858-60010 |
Encoder - Linear encoder IC - Detects carriage position as it moves along encoder strip |
| 3160-0814 |
Fan - Tubeaxial fan (Matsushita FBK-09A12M2-MOD) - 82.5mm (3.25in) mount hole spacing, 25.5mm (1.0in) thick, 12VDC, 35.3CFM |
| 9170-1535 |
Ferrite Assembly - Split ferrite - Installed inside electronics enclosure |
| 51642A |
Film - Polyester matte film - 61cm (24in) x 36.6m (120ft) roll |
| 51642B |
Film - Polyester matte film - 91.4cm (36in) x 36.6m (120ft) roll |
| 51642C |
Film - Polyester matte film - B size (11 x 17-inches) - 40 sheets |
| 51642F |
Film - Film (Matte) for DesignJet-C1633A, DesignJet 600, DesignJet 650, DesignJet 200 D size |
| 51642G |
Film - Polyester Matte Film - D Size - 22 x 34 inches (40 Sheets) |
| 51642H |
Film - Film (Matte) for DesignJet-C1633A, DesignJet 600, DesignJet 650, DesignJet 200 D size |
| 51642J |
Film - Polyester matte film - Architectural D size (24 x 36-inches) - 40 sheets |
| 51642K |
Film - Polyester matte film - E size (34 x 44-inches) - 40 sheets |
| 51642N |
Film - Polyester matte film - Architectural E size (36 x 48-inches) - 40 sheets |
| C2858-60162 |
Firmware - ROM SIMM (Version 5.2) - Plugs into main logic board |
| C1633-40019 |
Gear - Overdrive gear cluster |
| C1633-40027 |
Gear - Bail engaging lever gear |
| C1633-40028 |
Gear - Bail lift cam gear |
| C1633-60030 |
Gear - Clutch / overdrive gear assembly - Includes gear, clutch, retaining clip, and two washers. |
| C4705-60089 |
Gear Assembly - Clutch / overdrive gear assembly - Includes gear, clutch, retaining clip, and two washers |
| C4704-40109 |
Guide - MIO board guide |
| C1633-40030 |
Handle - Pinchwheel manual lift handle - Paper loading lever |
| 0510-0083 |
Hardware - Retaining E-ring - 0.250-in diameter, steel zinc-dichromate dip |
| 07575-40012 |
Hinge - Male half of hinge (on window) - For lift-up window |
| 07575-40111 |
Hinge - Female half of hinge (on chassis) - For lift-up window |
| C1633-40094 |
Holder - Holder - For 'Help' card and hand held cutter |
| C1633-00033 |
Housing - MIO support - Metal housing for the plug-in MIO card - Does not include the board guides |
| C2858-40001 |
Housing - Service station housing |
| C4704-60082 |
Housing - Housing assembly (on left side) |
| 1818-5637 |
IC ROM - EEPROM (U42) - On main logic board |
| 1818-6089 |
IC ROM - ROM - (U31)ON main logic board - Revision is 5.11 |
| 1818-6090 |
IC ROM - ROM - (U30)ON main logic board - Revision is 5.11 |
| 1818-6091 |
IC ROM - ROM - (U33)ON main logic board - Revision is 5.11 |
| 1818-6092 |
IC ROM - ROM - (U32)ON main logic board - Revision is 5.11 |
| C1633-00080 |
Insulator - Power supply insulator (Bottom) |
| C2847-00019 |
Insulator - Power supply insulator (Top) - Installed over the power supply |
| J2552A |
JetDirect - JetDirect CARD RJ45 10 BASE-T INTERNAL PRINT SERVER 10-100Base-TX or 10Base-2 Local Talk |
| J2593A |
JetDirect - External JetDirect LAN interface module with EtherTwist (10Base-T) and ThinLAN (10Base-2) input connectors and three parallel (DB-25) output connectors w/power supply. |
| J4106-60002 |
JetDirect - Hewlett Packard HP JetDirect 400N Internal Print Server J4106-60002 J4106A ID FOR RECV ONLY ORDER J4106-61001 (INTL USE ONLY) |
| 5041-1203 |
Keycap - Power switch keycap (White) |
| C2858-90169 |
Kit - DesignJet 650C manual kit - Includes 'Using Front Panel', 'Setting Up for Plotting', and 'Quick Reference' guides (English) |
| C2858-90170 |
Kit - DesignJet 650C manual kit - Includes 'Using Front Panel', 'Setting Up for Plotting', and 'Quick Reference' guides (Chinese) |
| C2858-90171 |
Kit - DesignJet 650C manual kit - Includes 'Using Front Panel', 'Setting Up for Plotting', and 'Quick Reference' guides (Thai) |
| C2858-90172 |
Kit - DesignJet 650C manual kit - Includes 'Using Front Panel', 'Setting Up for Plotting', and 'Quick Reference' guides (German) |
| C2858-90173 |
Kit - DesignJet 650C manual kit - Includes 'Using Front Panel', 'Setting Up for Plotting', and 'Quick Reference' guides (French) |
| C2858-90174 |
Kit - DesignJet 650C manual kit - Includes 'Using Front Panel', 'Setting Up for Plotting', and 'Quick Reference' guides (Spanish) |
| C2858-90175 |
Kit - DesignJet 650C manual kit - Includes 'Using Front Panel', 'Setting Up for Plotting', and 'Quick Reference' guides (Italian) |
| C2858-90176 |
Kit - DesignJet 650C manual kit - Includes 'Using Front Panel', 'Setting Up for Plotting', and 'Quick Reference' guides (Japanese) |
| C2858-90177 |
Kit - DesignJet 650C manual kit - Includes 'Using Front Panel', 'Setting Up for Plotting', and 'Quick Reference' guides (Portuguese) |
| C2858-90178 |
Kit - DesignJet 650C manual kit - Includes 'Using Front Panel', 'Setting Up for Plotting', and 'Quick Reference' guides (Korean) |
| C2848-60002 |
Leg - Leg assembly - Side support with foot bar and two casters |
| C2847-40013 |
Lever - Bail engaging lever - Used to move engaging lever gear |
| C2858-60209 |
Lifter - Bail lift mechanism kit - Includes cam gear, engaging lever, engaging lever gear, engaging lever spring, Y-tensioner bracket, bail lift cam, cam gear support, screws, and washers |
| 6040-0855 |
Lubricant - SYNTHETIC OIL (4oz Plastic Bottle) Front and Rear Slider Rods Synthetic oil - One plastic bottle of 3.5oz / 118.29 ML |
| 6040-0911 |
Lubricant - Special lubricating oil - For carriage slider rod surface - (syringe with 35cc oil) |
| C3190-60155 |
Lubricant - Grease - GREASE APPLICATION KITGrease - For helical gear (Drive roller gear) |
| C6074-60460 |
Lubricant - Grease - GREASE APPLICATION KITGrease - For helical gear (Drive roller gear) |
| 07595-90001 |
Manual - HP-GL Reference Guide - Programming Information |
| 5959-9733 |
Manual - Manual for Designjet 820 MFP Series, DesignJet-C1633A, DesignJet 600, DesignJet 650 |
| 5960-3743 |
Manual - Manual for DesignJet-C1633A, DesignJet 600, DesignJet 650, DesignJet 200 D size |
| C2858-90000 |
Manual - DesignJet 650C service manual (English) |
| C6072-60281 |
Manual - Toolbox and driver software - HP-GL/2 and RTL drivers for Windows 3.1/95/98/NT 4.0 (all DesignJets), and toolbox software for Windows 95/NT 4.0 (Only for DesignJet 430/450C/455CA/1050C/1055CM) - On 3.5-inch 1.44MB floppy disks (English) |
| C6072-60301 |
Manual - HP-GL/2 driver software for AutoCAD - For DOS and Windows 3.1/95/NT 4.0 - On 3.5-inch 1.44MB floppy disks (English) |
| C1633-00019 |
Media Bin - Media bin back - For top of wire rack below plotter |
| C1633-00020 |
Media Bin - Media bin front - Main part of wire rack below plotter |
| C1633-00044 |
Media Bin - Media bin adjust - Adjustable media bottom stop in wire rack |
| C2065A |
Memory - 4MB, 80nS, 36-bit SIMM memory module - For HP Plotters, LaserJet IIISi, 4/4M, 4Si/MX and other models. |
| C2066A |
Memory - 8MB, 80nS, 36-bit SIMM memory module - For HP LaserJet IIISi, 4/4M, 4Si/MX |
| D2152-63001 |
Memory - 8MB, 80nS, 36-bit SIMM memory module |
| D2152-69001 |
Memory - 8MB, 80nS, 36-bit SIMM memory module |
| D2156-63001 |
Memory - 4MB, 80nS, 36-bit SIMM memory module |
| D2156-69001 |
Memory - 4MB, 80nS, 36-bit SIMM memory module |
| D2297-63001 |
Memory - 16MB, 70nS, 36-bit SIMM memory module |
| D2297-69001 |
Memory - 16MB, 70nS, 36-bit SIMM memory module |
| D2297A |
Memory - 16MB, 70nS, 36-bit parity SIMM memory module |
| D2298-69001 |
Memory - 32MB, 70nS, 36-bit parity SIMM memory module |
| D3578-63001 |
Memory - 32MB, 70nS, 36-bit parity SIMM memory module |
| D3578-69001 |
Memory - 32MB, 70nS, 36-bit parity SIMM memory module |
| D3578A |
Memory - 32MB, 70nS, 36-bit parity SIMM memory module |
| J2382-69003 |
Module - External JetDirect LAN interface module with EtherTwist (10Base-T) and ThinLAN (10Base-2) connectors |
| J2383-61005 |
Module - External token ring interface module - Has DB-9 connector |
| J2590-61011 |
Module - External JetDirect LAN interface module with RJ-45 connector for EtherTwist (10Base-T) or 100VG/802.12 input and three parallel (DB-25) output connectors |
| J2590-69001 |
Module - External JetDirect LAN interface module with RJ-45 connector for EtherTwist (10Base-T) or 100VG/802.12 input and three parallel (DB-25) output connectors |
| J2592-61001 |
Module - External JetDirect LAN interface module with EtherTwist (10Base-T) connector |
| J2592-69001 |
Module - External JetDirect LAN interface module with EtherTwist (10Base-T) connector |
| J2593-69001 |
Module - External JetDirect LAN interface module with EtherTwist (10Base-T) and ThinLAN (10Base-2) input connectors and three parallel (DB-25) output connectors w/power supply. |
| J2594-61011 |
Module - External JetDirect token ring interface module with DB-9 and RJ-45 input connectors and three parallel (DB-25) output connectors |
| J3258-61021 |
Module - External JetDirect LAN interface module with EtherTwist (10Base-T) connector |
| J4102-61021 |
Module - External JetDirect LAN interface module with EtherTwist (10Base-T) connector |
| J4102-69022 |
Module - External JetDirect LAN interface module with EtherTwist (10Base-T) connector |
| C2847-60221 |
Motor - Motor assembly - Includes power cable |
| C2848-60003 |
Motor - Motor/encoder assembly (includes helical drive gear) - 'X' axis drive - NOTE: motor and gear are only sold as a set |
| C1633-20006 |
Mount - 'X' axis motor mount |
| C1633-40089 |
Mount - Overdrive mount block |
| C2858-00017 |
NamePlate - Nameplate - DesignJet 650C printer logo |
| C4706-60121 |
Overdrive Assembly - Overdrive support assembly (E) |
| C2858-60026 |
Overlay - Control panel overlay (English) |
| C2858-60027 |
Overlay - Control panel overlay (German) |
| C2858-60028 |
Overlay - Control panel overlay (Spanish) |
| C2858-60029 |
Overlay - Control panel overlay (French) |
| C2858-60030 |
Overlay - Control panel overlay (Japanese) |
| C2858-60031 |
Overlay - Control panel overlay (Italian) |
| C2858-60033 |
Overlay - Control panel overlay (Portuguese) |
| C3196-60113 |
Packaging - Repackaging Kit - for Main Plotter Unit |
| 51630Y |
Paper - Color InkJet CX cut sheet paper - A size (8.5 x 11-inches) - 200 sheets per package |
| 51630Z |
Paper - Color InkJet CX cut sheet paper - A4 size (21.0cm x 29.7cm) - 200 sheets per package |
| 51631A |
Paper - Color InkJet CX cut sheet paper - B size (11 x 17-inches) - 200 sheets per package |
| 51631B |
Paper - Color InkJet CX cut sheet paper - A3 size (29.7cm x 42.0cm) - 200 sheets per package |
| 51631D |
Paper - Color InkJet paper - 61cm (24in) x 45.7m (150ft) roll |
| 51631E |
Paper - Color InkJet paper - 91.4cm (36in) x 45.7m (150ft) roll |
| 51631G |
Paper - Color InkJet paper - 61cm (24in) x 45.7m (150ft) roll |
| 51631H |
Paper - Color InkJet cut sheet paper - A1 size (59.4cm x 84.1cm) - 100 sheets per package |
| 51648D |
Paper - Heavyweight color InkJet paper - 61cm (24in) x 45.7m (150ft) roll |
| 51648E |
Paper - Heavyweight color InkJet paper - 91.4cm (36in) x 45.7m (150ft) roll |
| C1861A |
Paper - HP Bright white InkJet paper - 91.4cm (36in) x 45.7m (150ft) roll |
| C3859A |
Paper - Paper - transparencies, continuous forms - Roll A0 91.4 cm x 45.7 m) - 67 g/m2 - 1 pcs. |
| C3887A |
Paper - Special InkJet cut sheet paper - E size (34 x 44-inches) - 100 sheets per package |
| C6020B |
Paper - Coated paper (98 gsm) - 91.4cm (36in) x 45.7m (150ft) roll (USA, Canada, and Latin America) |
| 0950-2417 |
PC Board - Power supply board |
| C2858-60105M |
PC Board - Interconnect board |
| C2858-60207 |
PC Board - Main Logic Board, HP OEM DesignJet MAIN LOGIC PCA BOARD FOR 650C |
| C2858-69207 |
PC Board - Main logic board, HP OEM DesignJet MAIN LOGIC PCA BOARD FOR 650C |
| J2550-69013 |
PC Board - EtherTwist 10Base-T LAN interface board |
| J2555-69013 |
PC Board - JetDirect Card Token RingToken ring LAN interface board - DB-9 and RJ-45 connectors |
| J3258-61011 |
PC Board - External JetDirect 170X LAN interface module - Interfaces a parallel printer to an ethernet 10Base-T (RJ-45) LAN |
| J4100-69001 |
PC Board - JetDirect 400N modular input/output (MIO) internal print server - Provides 10/100Base-TX or 10Base-2 network connection using RJ45 or BNC connectors |
| J2550B |
PC Board Interface - EtherTwist (10Base-T) LAN interface board, JetDirect card has one 10 Mbps RJ45 Ethernet connector. |
| J2552B |
PC Board Interface - LAN and LocalTalk interface - Has EtherTwist (10Base-T) , ThinLAN (10Base-2) , and LocalTalk (DIN-8) connectors |
| J2555B |
PC Board Interface - JetDirect Card Token RingToken ring LAN interface board - DB-9 and RJ-45 connectors |
| J2590A |
PC Board Interface - External JetDirect LAN interface module with RJ-45 connector for EtherTwist (10Base-T) or 100VG/802.12 input and 3 parallel (DB-25) output connectors |
| J2591-69001 |
PC Board Interface - External JetDirect LAN interface module with EtherTwist (10Base-T) and ThinLAN (10Base-2) connectors |
| J2591A |
PC Board Interface - External JetDirect LAN interface module and power module - Has EtherTwist (10Base-T) and ThinLAN (10Base-2) connectors |
| J2594-69001 |
PC Board Interface - External JetDirect token ring interface module with DB-9 and RJ-45 input connectors and three parallel (DB-25) output connectors |
| J3258-61041 |
PC Board Interface - External JetDirect 170X LAN interface module - Interfaces a parallel printer to an ethernet 10Base-T (RJ-45) LAN |
| J3258B |
PC Board Interface - External JetDirect 170X LAN interface module - Interfaces a parallel printer to an ethernet 10Base-T (RJ-45) LAN |
| J3264A |
PC Board Interface - HP JetDirect 500X external token ring print server module - Interfaces up to 3 parallel printers to a token ring (DB-9 or RJ-45) LAN |
| J3265-69001 |
PC Board Interface - External JetDirect LAN interface module with EtherTwist (10Base-T and ThinLAN) (10Base-2) input connectors and three parallel (DB-25) output connectors |
| J3265G |
PC Board Interface - HP JetDirect 500X external token ring print server module - Interfaces up to 3 parallel printers to an ethernet 10Base-T (RJ-45), 10Base2 (BNC), or 100Base-TX (RJ-45) LAN |
| J4101B |
PC Board Interface - HP JetDirect 300X external print server module (10Base-T and 100Base-TX) - Connects between printer parallel port and LAN network |
| J4102B |
PC Board Interface - External JetDirect LAN interface module with EtherTwist (10Base-T) connector |
| C1633-00009 |
Plate - Axial Bias Plate - Installed between the paper drive (Platen) Roller Assembly and the right frame |
| C2847-00027 |
Plate - SIMM Plate - Covers access to SIMM slot connectors |
| C2848-00010 |
Platen - Entry platen - Installed over the paper drive (platen) roller assembly |
| C2882-60001 |
PostScript - Adobe's PostScript (Level two) SIMM module |
| C2882-60101 |
PostScript - Adobes PostScript (Level two) SIMM module |
| C3545-60001 |
PostScript - Adobe's PostScript (level two) SIMM module |
| C3545-60101 |
PostScript - Adobes PostScript (Level two) SIMM module |
| 8120-0698 |
Power Cord - Power cord (Black) - 18 AWG, 2.3m (7.5ft) long - Has straight (F) receptacle (for 220V in the USA and Canada) |
| 8120-1351 |
Power Cord - Power cord (Mint Gray) - 17 AWG, 2.3m (7.5ft) long - Has straight (F) receptacle (for 240V in the UK, Hong Kong, Singapore, Malaysia, and Brunei) |
| 8120-1369 |
Power Cord - Power cord (Mint Gray) - 17 AWG, 2.0m (6.6ft) long - Has straight (F) receptacle (for 240V in Australia, New Zealand, and China) |
| 8120-1378 |
Power Cord - Power cord (Jade Gray) - 18 AWG, 2.3m (7.5ft) long - Has straight (F) C13 receptacle (for 120V in USA, Canada, Latin America, Korea, Taiwan, Thailand, Spain, Brazil, and Vietnam) |
| 8120-1689 |
Power Cord - Power cord (Mint Gray) - 17 AWG, 2.0m (6.6ft) long - Has straight (F) receptacle (for 220V in Europe, Bangladesh, Indonesia, Pakistan, Burma, Sri Lanka, and Vietnam) |
| 8120-2104 |
Power Cord - Power cord (Mint Gray) - 2.0m (6.6ft) long - Has straight (F) receptacle (for 220V in Switzerland) |
| 8120-2956 |
Power Cord - Power cord (Mint Gray) - 2.0m (6.6ft) long - Has straight (F) receptacle (for 220V in Denmark) |
| 8120-4211 |
Power Cord - Power cord (Mint Gray) - 17 AWG, 2.0m (6.6ft) long - Has straight (F) receptacle (for 240V in South Africa and India) |
| 8120-4753 |
Power Cord - Power cord (Flint Gray) - 18 AWG, 2.3m (7.5ft) long - Has straight (F) receptacle (for 100V in Japan) |
| 8120-6302 |
Power Cord - Daisy chain power cord (Dove Gray) - 18 AWG, 1.2m (4.0ft) long - Has C14 (M) plug for power input and C13 (F) plug for power output |
| 8121-0877 |
Power Cord - Power cord (Black) - 18 AWG, 2.3m (7.5ft) long - Has straight (F) receptacle (for 220V in the USA and Canada) |
| 0950-2372 |
Power Module - Power supply module - 100-240VAC input, 47-63Hz, requires separate AC power cord - 5VDC output, 1A, 5 watts |
| 0950-3169 |
Power Module - Wall mount power supply module - 120VAC input 60Hz power supply AC DC 15W UNIVERSAL ADAPTER Power module (wall mount)- Input voltage 100-240 VAC - Output voltage 12 VDC, 15 watts output, 1.0A - for Jet Direct power and other accessories. |
| 0950-3171 |
Power Module - Power supply module - 220-240VAC input, 47-53Hz - 13VDC output, 300mA (U. K. and Hong Kong) |
| 0950-3172 |
Power Module - Power supply module - 240VAC input, 47-53Hz - 13VDC output, 300mA (Australia) |
| 0950-3349 |
Power Module - Universal AC power adapter - wide-range, 40c - Requires separate country-specific power cord with C7 connector Power supply module - 120VAC input, 60Hz - 12VDC output, 1.0A |
| 0950-3350 |
Power Module - Wall mount power supply module (Leader Electronics 48130625HK) - 200VAC input, 48-52Hz - 13VDC output, 625mA (Hong Kong) |
| 0950-3351 |
Power Module - Wall mount power supply module (MEI-AH ED12009) - 220VAC input, 47-63Hz - 13VDC output, 800mA, 10.4 watts (South Korea) |
| 0950-3352 |
Power Module - Wall mount power supply module (MEI-AH ED12010) - 100VAC input, 47-63Hz - 13VDC output, 800mA, 10.4 watts (for use in Japan) |
| 0950-3354 |
Power Module - Wall mount power supply module (MEI-AH ED12010) - 220-250VAC input, 47-53Hz - 13VDC output, 800mA, 10.4 watts (South Africa) |
| 0957-2109 |
Power Module - Power supply module - 209-253VAC input, 47-53Hz - 13VDC output, 800mA (Europe and Israel) |
| 0957-2110 |
Power Module - Wall mount power supply module - 120VAC input 60Hz power supply AC DC 15W UNIVERSAL ADAPTER Power module (wall mount)- Input voltage 100-240 VAC - Output voltage 12 VDC, 15 watts output, 1.0A - for Jet Direct power and other accessories. |
| 0957-2134 |
Power Module - Wall mount power supply module (MEI-AH ED12010) - 100VAC input, 47-63Hz - 13VDC output, 800mA, 10.4 watts (for use in Japan) |
| 0957-2197 |
Power Module - Wall mount power supply module - 120VAC input 60Hz power supply AC DC 15W UNIVERSAL ADAPTER Power module (wall mount)- Input voltage 100-240 VAC - Output voltage 12 VDC, 15 watts output, 1.0A - for Jet Direct power and other accessories. |
| 0957-2340 |
Power Module - Wall mount power supply module - 120VAC input 60Hz power supply AC DC 15W UNIVERSAL ADAPTER Power module (wall mount)- Input voltage 100-240 VAC - Output voltage 12 VDC, 15 watts output, 1.0A - for Jet Direct power and other accessories. |
| 0957-2481 |
Power Module - Pwra brk uni 12vdc 15w |
| 5188-5676 |
Power Module - Power module (wall mount) - Input voltage 100VAC, 47/63Hz - Output voltage 13VDC, 800mA, 10.4 watts (for use in Japan) |
| 5188-6700 |
Power Module - Universal AC power adapter - wide-range, 40c - Requires separate country-specific power cord with C7 connector |
| 9100-5176 |
Power Module - Pwer supply, 13v/300ma jpn |
| 0950-2623 |
Power Supply - Switching power supply (Delta DPS-158ABA) - 100-240VAC input, 47-63Hz - Four DC outputs (5.15V, +12V, -12V, 24V) - 158 watts - Includes upgrade sticker |
| 0957-2192 |
Power Supply - Power supply module - 209-253VAC input, 47-53Hz - 13VDC output, 800mA (Europe and Israel) |
| 0957-2194 |
Power Supply - Wall mount power supply module (MEI-AH ED12009) - 220VAC input, 47-63Hz - 13VDC output, 800mA, 10.4 watts (South Korea) |
| 0957-2228 |
Power Supply - Wall mount power supply module - 120VAC input 60Hz power supply AC DC 15W UNIVERSAL ADAPTER Power module (wall mount)- Input voltage 100-240 VAC - Output voltage 12 VDC, 15 watts output, 1.0A - for Jet Direct power and other accessories. |
| 0957-2229 |
Power Supply - Power module (wall mount)- Input voltage 220-250VAC, 47/53Hz - Output voltage 13VDC, 800mA, 10.4W (Worldwide) |
| 5188-5673 |
Power Supply - Universal AC power adapter - wide-range, 40c - Requires separate country-specific power cord with C7 connector Power supply module - 120VAC input, 60Hz - 12VDC output, 1.0A |
| C3195-60168 |
Power Supply - Power Supply Board for Hewlett Packard Plotters. |
| C4705-60109 |
Primer - Primer assembly - Mounts under the service station assembly on the left side of the plotter |
| J2341-60128 |
Print Server - AppleTalk (LocalTalk) interface board - Has DIN-8 connector |
| J3265A |
Print Server - External JetDirect 500X LAN interface module - Interfaces up to 3 parallel printers to an ethernet 10Base-T (RJ-45), 10Base2 (BNC), or 100Base-TX (RJ-45) LAN |
| J4100-61001 |
Print Server - JetDirect 400N modular input/output (MIO) internal print server - Provides 10/100Base-TX or 10Base-2 network connection using RJ45 or BNC connectors |
| J4101-61011 |
Print Server - External JetDirect LAN interface module with EtherTwist 10Base-T/100BaseTX connector |
| J4169-61001 |
Print Server - JetDirect 610N Internal Print Server (10Base-T and 100Base-TX) LAN Interface Board - Has one RJ-45 connector |
| 07570-60105 |
Pulley - Idler pulley - For main drive belt |
| 07570-60112 |
Pulley - Idler drive pulley - Applies tension to the pen carriage drive belt (small belt) |
| C3170-60009 |
Pulley - Reduction pulley - Includes 2 Bearings, Shaft (0.16in Diameter on Both Ends), Flange, Pulley and Instructions |
| C1633-60020 |
Receptacle - AC power recptacle assembly - Includes receptacle, wires, grounding lug, and socket to power supply |
| 5183-5268 |
Recovery Kit - Recovery Kit for DeskJet 1200 Series, DeskJet 850 Series, DeskJet 1000 Series, DeskJet 1100 Series |
| 5184-2833 |
Recovery Kit - Return kit - For returning defective Thermal InkJet (TIJ) 2.5 cartridges - Includes box and instructions |
| C3792A-Repair_DesignJet |
Repair Service - Ship your product to us for a small diagnostic fee; and a professional service job. We will contact you with repair total and your diagnostic fee will be waived if unit is repaired. Service warranty is 30days labor and 90days for parts. Extended warranty option is available. |
| C2858-40038 |
Reservoir - Reservoir - Attaches to left side chassis - Ink absorber is inserted into this reservoir |
| C2858-40039 |
Reservoir - Ink drop reservoir - Installs on right side of plotter |
| C2859-60004 |
Roller - Paper drive (platen) roller assembly - Long gear driven roller |
| C4700-60042 |
Roller - Paper drive (platen) roller assembly - Long gear driven roller - Includes roller and mark encoder |
| C4704-60199 |
Rollfeed Assembly - Brake/housing assembly (on right side) - Accepts the flange end of the spindle rod assembly - Includes the 2 housing pieces, 2 brake shoes, brake gear, brake lever, and springs |
| C2847-60021 |
Sensor - Media sensor assembly - Includes cable |
| C2847-60069 |
Sensor - Sensor assembly |
| C2858-60007 |
Sensor - Optical primer sensor |
| C3180-60034 |
Sensor - Pincharm sensor - Includes cable |
| C3792A-Manual_DesignJet |
Service Manual - Printer Service Manual - Includes troubleshooting, error messages, paper jams, parts and parts diagrams. |
| C7769-90066 |
Service Manual - DesignJet support DVD-ROM - Version A.04.01 - Has product information, user's manuals, service manuals, diagnostic software, test drawings, newsletters, and service notes |
| 5960-8286 |
Service Parts - Shipping Material/Carton for DesignJet 200 D size, DesignJet 650, DesignJet 200 E size |
| C2858-60152 |
Service Station - Service station kit - Includes service station cap, four primer tubes, absorber, sled, wiper, drop detect sensor, and bail sensor cable |
| C4704-40050 |
Shield - SIMM module shield |
| C6072-60284 |
Software - Toolbox and driver software - HP-GL/2 and RTL drivers for Windows 3.1/95/98/NT 4.0 (all DesignJets), and toolbox software for Windows 95/NT 4.0 (Only for DesignJet 430/450C/455CA/1050C/1055CM) - On 3.5-inch 1.44MB floppy disks (German) |
| C6072-60285 |
Software - Toolbox and driver software - HP-GL/2 and RTL drivers for Windows 3.1/95/98/NT 4.0 (all DesignJets), and toolbox software for Windows 95/NT 4.0 (Only for DesignJet 430/450C/455CA/1050C/1055CM) - On 3.5-inch 1.44MB floppy disks (French) |
| C6072-60286 |
Software - Toolbox and driver software - HP-GL/2 and RTL drivers for Windows 3.1/95/98/NT 4.0 (all DesignJets), and toolbox software for Windows 95/NT 4.0 (Only for DesignJet 430/450C/455CA/1050C/1055CM) - On 3.5-inch 1.44MB floppy disks (Spanish) |
| C6072-60287 |
Software - Toolbox and driver software - HP-GL/2 and RTL drivers for Windows 3.1/95/98/NT 4.0 (all DesignJets), and toolbox software for Windows 95/NT 4.0 (Only for DesignJet 430/450C/455CA/1050C/1055CM) - On 3.5-inch 1.44MB floppy disks (Italian) |
| C6072-60304 |
Software - HP-GL/2 driver software for AutoCAD - For DOS and Windows 3.1/95/NT 4.0 - On 3.5-inch 1.44MB floppy disks (German) |
| C6072-60305 |
Software - HP-GL/2 driver software for AutoCAD - For DOS and Windows 3.1/95/NT 4.0 - On 3.5-inch 1.44MB floppy disks (French) |
| C6072-60306 |
Software - HP-GL/2 driver software for AutoCAD - For DOS and Windows 3.1/95/NT 4.0 - On 3.5-inch 1.44MB floppy disks (Spanish) |
| C6072-60307 |
Software - HP-GL/2 driver software for AutoCAD - For DOS and Windows 3.1/95/NT 4.0 - On 3.5-inch 1.44MB floppy disks (Italian) |
| C2848-60011 |
Spindle - Rollfeed spindle rod assembly (E-size 36 inch ) - Includes spindle and end caps |
| C3173A |
Spindle - E/A0 rollfeed spindle rod assembly for DesignJet 6xx/7xx - Includes spindle and end caps |
| 1460-2061 |
Spring - Extension spring - Zinc plated music wire, 0.875in long, 0.187in OD, 0.020in wire diameter, 1.8 in/lb rate - For pen carriage drive belt pulley tensioning wedge |
| C1633-80004 |
Spring - Extension spring - Holds the rollfeed access cover closed |
| C1633-80006 |
Spring - Bail engaging lever spring |
| C1633-80014 |
Spring - Compression spring - For the rear bushing on the carriage |
| C2858-00006 |
Spring - Encoder spring for HP DesignJet 650C Series |
| C4723-80027 |
Spring - Cutter shim/bail spring |
| C4713-60035 |
Starwheel - Starwheel mount assembly - Includes cover, body, spring and two starwheels |
| C4714-60098 |
Strip - Encoder strip assembly (E-size) - Includes encoder strip and encoder strip spring |
| C2847-40015 |
Support - Cam gear support |
| C2847-60044 |
Switch - Power switch assembly - Includes cable |
| 07550-40104 |
Wedge - Tensioning wedge (cam tensioner) - For the pen carriage drive belt pulley |
| 07570-40105 |
Wedge - Main tensioning wedge - For the carriage drive belt idler pulley |
| C1633-40075 |
Window - Lift-up viewing window (Clear) |
Techical Help
View service parts