| RB1-6134-040CN |
Arm - Tray 1 sensor arm |
| RB2-1781-000CN |
Arm - Multi purpose tray paper sensor lever |
| RB2-1782-000CN |
Arm - Lower tray paper sensor lever |
| RB2-1856-000CN |
Arm - Toner cartridge engagemnet arm |
| RB2-1856-040CN |
Arm - Toner cartridge engagemnet arm |
| RB3-0443-000CN |
Arm - Lever link - Mechanical link between paper sensor flag and sensor holder |
| RF5-2635-000CN |
Arm - Paper arm for HP LaserJet 5000 Series |
| RB2-1887-000CN |
Belt - Large feed belt - Wide belt in middle of assembly |
| RB2-1888-000CN |
Belt - Small paper feed belt - One on each side of wide belt ( 2 included). |
| RG5-4914-000CN |
Belt - Paper feed belt assembly |
| RB1-6177-000CN |
Bushing - Tray 1 and 2 pickup shaft bushing - Right side |
| RB1-6179-000CN |
Bushing - Tray 1 and 2 pickup shaft bushing - Right side |
| RB2-1988-000CN |
Bushing - Right side bushing for lower delivery roller |
| RB2-1988-020CN |
Bushing - Right side bushing for lower delivery roller |
| RB2-1989-000CN |
Bushing - Left side bushing for lower delivery roller |
| RS5-1392-000CN |
Bushing - Tray 1 and 2 left side pickup roller shaft bushing |
| 5063-1256 |
Cable - IEEE-1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36-pin Centronics (M) connector (type B) - 2.0m (6.6ft) long |
| C2950A |
Cable - IEEE 1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36-pin Centronics (M) connector (type B) - 2.0m (6.6ft) long |
| RG5-3523-000CN |
Cable - Cable assembly for HP LaserJet 5000 Series |
| RG5-3554-000CN |
Cable - Face down bin full cable |
| RG5-3558-000CN |
Cable - Top of page sensor cable |
| RG5-3561-000CN |
Cable - HP Cable for LaserJets, fuser cable. |
| RG5-3575-000CN |
Cable - Control panel cable |
| RG5-7072-000CN |
Cable - Scanner cable for HP LaserJet 5100 Series |
| RG5-7073-000CN |
Cable - Cable assembly - A 20-pin (F) connector to two 14cm (5.5in) cables with 7-pin (F) connectors, a 31.5cm (12.4in) cable with a 9-pin (F) connector, and a 39.4cm (15.5in) cable with a 3-pin (F) connector |
| RG5-7086-000CN |
Cable - Ribbon cable - From paper handling PC Board to controller PC Board |
| RG5-7198-000CN |
Cable - Upper contact cable |
| RG9-1460-000CN |
Cable - Control panel cable |
| RH2-5337-000CN |
Cable - Ribbon cable - Has two 40-pin (M) edge connectors - 1.4cm (0.6in) long |
| U9888E |
Care Pack - HP Maintenance Kit Replacement 110v Fuser for LaserJet 5100 Service |
| 5184-5224 |
Cartridge - Black toner cartridge - With 'Ultra-Precise' toner - Has maximum capacity toner (Prints approximately 10,000 pages) |
| 6R925 |
Cartridge - 29x hi yield black toner |
| C4129X |
Cartridge - Black toner cartridge - With 'Ultra-Precise' toner - Has maximum capacity toner (Prints approximately 10, 000 pages) |
| 5090-3379 |
Cleaner - Toner cleaning cloth - Specially treated cloth for absorbing toner (1 per package) - Ideal for cleaning up toner spills |
| XD2-1100-322CN |
Clip - E-ring retainer clip |
| RH7-5345-000CN |
Clutch - Paper feed clutch - For Tray 2 |
| RH7-5346-000CN |
Clutch - Paper feed roller clutch - For Tray 2 |
| WS1-6204-000CN |
Connector - Replacement for part(s).Power connector - Supplies power to optional paper trays |
| WS6-5092-000CN |
Connector - Power connector - Supplies power to optional paper trays |
| RG5-5438-030CN |
Control Panel - Control panel - Does not include overlay |
| RB2-3314-000CN |
Coupler - Pickup roller coupler |
| Q1860-67904 |
Cover - Hewlett Packard LaserJet Front cover assembly - Drop down paper tray assembly |
| RB2-1747-030CN |
Cover - Face down auxiliary cover |
| RB2-1748-000CN |
Cover - Top cover - Rear portion of the top cover |
| RB2-1749-040CN |
Cover - Right side cover assembly |
| RB2-1755-020CN |
Cover - Right corner cover - - Located below the front drop down tray |
| RB2-1756-020CN |
Cover - Left corner cover - Located below the front drop door tray |
| RB2-1758-000CN |
Cover - Display cover - Control panel display cover |
| RB2-1905-000CN |
Cover - Transfer roller bushing cover - Right side |
| RB3-0441-000CN |
Cover - Tray cover - Rear tray cover for 500 sheet universal paper tray |
| RG5-3547-080CN |
Cover - Front inner cover assembly - With tray 1 sensor arm, arm spring and tray 1 leaf spring |
| RG5-3550-040CN |
Cover - Left side cover assembly |
| RG5-3551-100CN |
Cover - Rear cover assembly |
| RG5-7080-000CN |
Cover - Front cover assembly - Drop down paper tray assembly |
| RG5-3556-000CN |
Door - Toner cartridge access door assembly |
| RG5-3556-040CN |
Door - Toner cartridge access door assembly |
| Q1860-69013 |
Drive Assembly - Main drive gear assembly - On left side of printer |
| RG5-7079-040CN |
Drive Assembly - Main drive gear assembly - Located on left side of the printer |
| RG5-7194-000CN |
Drive Assembly - Gear drive assembly - Drive gears for 500 sheet paper pickup |
| RG9-1524-000CN |
Drive Assembly - Paper pickup drive assembly |
| Q1860-69010 |
Duplexer - Duplexer assembly |
| Q1864A |
Duplexer - Duplexer assembly |
| RH7-1552-000CN |
Fan - Cooling Fan - Lower Right Rear |
| Q1866A |
Feeder - 500-sheet feeder and paper tray - Printer sits on top of this unit - Includes 500-sheet paper cassette |
| RB1-7501-020CN |
Flag - Paper feed sensor flag - Black plastic shaft with two arms on it (One is moved by the feeding paper, the other activates the photo sensor) - Mounts under the top plate on the 250-sheet paper feeder assembly base unit |
| Q1860-69008 |
Fuser Assembly - HP Laserjet 5100 Fuser Assembly 110V-120V |
| Q1860-69025 |
Fuser Assembly - Fuser Assembly - 110 volts |
| Q1860-69032 |
Fuser Assembly - Fuser Assembly - 110 volts Fuser Assembly - For 110 VAC operation - Bonds toner to the paper with heat |
| Q1860-69033 |
Fuser Assembly - Fusing assembly - For 220 VAC operation - Bonds toner to the paper with heat |
| RG5-7060-140CN |
Fuser Assembly - Fuser Assembly - 110 volts |
| RG5-7060-190CN |
Fuser Assembly - Fusing assembly - For 110 VAC operation - Bonds toner to the paper with heat |
| RG5-7061-140CN |
Fuser Assembly - Fuser Assembly - 220 volts |
| RG5-7061-190CN |
Fuser Assembly - Fusing assembly - For 220 VAC operation - Bonds toner to the paper with heat |
| RB1-6130-000CN |
Gear - Tray 1 pickup roller gear |
| RS5-0695-000CN |
Gear - Tray 2 pickup roller shaft drive gear |
| RS6-0357-000CN |
Gear - Delivery roller shaft gear |
| RB2-1774-000CN |
Guide - Toner cartridge guide - Left side |
| RB2-1775-000CN |
Guide - Toner cartridge guide - Right side |
| RB2-1780-000CN |
Guide - Paper guide - Guides paper from pickup roller to feed roller |
| RF5-4118-000CN |
Guide - Transfer guide assembly - Guides paper into transfer roller |
| RG5-3520-060CN |
Guide - Paper guide - Tray 1 paper guide plate assembly |
| RG5-3525-000CN |
Guide - Transfer guide assembly - Guides paper into transfer roller |
| RG5-3548-060CN |
Guide - Transfer guide assembly - Includes the width adjuster for the drop down tray |
| RG5-6197-000CN |
Guide - Paper guide - Tray 1 paper guide plate assembly |
| RB2-1997-000CN |
Holder - Roller holder - Face down guide roller holder |
| RB3-0444-000CN |
Holder - Sensor holder - Holds sensor used with paper sensor flag |
| RB1-2190-000CN |
Hook - Pickup roller spring hook |
| Q1860-69004 |
Laser Scanner - Laser/scanner assembly |
| RG5-7041-000CN |
Laser Scanner - Laser/scanner assembly |
| RB2-1791-000CN |
Lever - Sensor lever - Tray 2 paper out sensor |
| RB2-1807-000CN |
Lever - Sensor flag lever - Paper feed sensor arm |
| RB2-1980-000CN |
Lever - Bin full lever - Face down output tray sensor lever |
| RB3-0431-000CN |
Lever - Sensor flag lever - Paper feed sensor arm |
| RF5-2421-000CN |
Lever - Shutter lever - Connects to laser shutter |
| RB2-2042-000CN |
Lock - Extension lock - Paper length extension lock |
| Q1860-67902 |
Maintenance Kit - Maintenance kit - LaserJet 5100 maintenance kit - Include(120V) fusing roller, transfer roller, Tray 1/250 sheet tray separation pad and pickup roller, 500 sheet separation/feed and pickup roller, cleaning brush |
| Q1860-67910 |
Maintenance Kit - Maintenance kit - LaserJet 5100 maintenance kit - Includes (120V) fusing roller, transfer roller, Tray 1/250 sheet tray separation pad and pickup roller, 500 sheet separation/feed and pickup roller, cleaning brush, gloves and installation instructions |
| Q1860-67911 |
Maintenance Kit - Maintenance kit - LaserJet 5100 maintenance kit - Includes (220V) fusing roller, transfer roller, Tray 1/250 sheet tray separation pad and pickup roller, 500 sheet separation/feed and pickup roller, cleaning brush, gloves and installation instructions |
| Q1860-67914 |
Maintenance Kit - Maintenance kit - LaserJet 5100 maintenance kit - Includes (120V) fusing roller, transfer roller, Tray 1/250 sheet tray separation pad and pickup roller, 500 sheet separation/feed and pickup roller, cleaning brush, gloves and installation instructions |
| Q1860-67915 |
Maintenance Kit - LaserJet 5100 maintenance kit - Includes (220V) fusing roller, transfer roller, Tray 1/250 sheet tray separation pad and pickup roller, 500 sheet separation/feed and pickup roller, MP Tray separation pad, cleaning brush, gloves and instructions |
| Q1860-69002 |
Maintenance Kit - LaserJet 5100 maintenance kit - Includes fusing for 110 VAC, transfer roller, 250-sheet tray separation pad and pickup roller, 500-sheet separation/feed roller and pickup roller. |
| Q1860-69023 |
Maintenance Kit - Maintenance kit - LaserJet 5100 maintenance kit - Includes (220V) fusing roller, transfer roller, Tray 1/250 sheet tray separation pad and pickup roller, 500 sheet separation/feed and pickup roller, MP Tray separation pad, cleaning brush, gloves and inst |
| Q1860-69027 |
Maintenance Kit - Maintenance kit - LaserJet 5100 maintenance kit - Includes (120V) fusing roller, transfer roller, Tray 1/250 sheet tray separation pad and pickup roller, 500 sheet separation/feed and pickup roller, cleaning brush, gloves and installation instructions |
| Q1860-69028 |
Maintenance Kit - Maintenance kit - LaserJet 5100 maintenance kit - Includes (220V) fusing roller, transfer roller, Tray 1/250 sheet tray separation pad and pickup roller, 500 sheet separation/feed and pickup roller, MP Tray separation pad, cleaning brush, gloves and inst |
| Q1860-69034 |
Maintenance Kit - Maintenance kit - For LaserJet 5100 maintenance kit - Includes 120 VAC fusing roller, transfer roller, tray 1 250-sheet tray separation pad and pickup roller, 500-sheet separation/feed and pickup roller, cleaning brush, gloves and installation instruction |
| Q1860-69035 |
Maintenance Kit - LaserJet 5100 maintenance kit - Includes (220V) fusing roller, transfer roller, Tray 1/250 sheet tray separation pad and pickup roller, 500 sheet separation/feed and pickup roller, MP Tray separation pad, cleaning brush, gloves and instructions |
| Q1860-90918 |
Manual - Q1860-90918 |
| Q1860-90930 |
Manual - Q1860-90930 |
| Q1860-90932 |
Manual - Q1860-90932 |
| 5062-4667 |
Memory - Font DIMM - Greek Font memory DIMM |
| 5062-4668 |
Memory - Font DIMM - Hebrew Font memory DIMM |
| 5062-4670 |
Memory - Font DIMM - Arabic Font memory DIMM |
| 5181-3532 |
Memory - Font DIMM - Ukrainian/Cyrillic Font memory DIMM |
| C4140-67901 |
Memory - 4MB, 100-pin SDRAM DIMM memory module |
| C4286A |
Memory - 2MB flash DIMM memory - Font storage device |
| C4287A |
Memory - 4MB flash DIMM memory - Font storage device |
| C7842-67901 |
Memory - 8MB, 100-pin SDRAM DIMM memory module |
| C7842A |
Memory - 4MB, 100-pin SDRAM DIMM memory module |
| C7842AX |
Memory - 8MB, 100MHz SDRAM DIMM memory module |
| C7843-67901 |
Memory - 16MB, 100-pin SDRAM DIMM memory module (Part approaching End of Life, please contact HP for availability) |
| C7843A |
Memory - 16MB, 100-pin SDRAM DIMM memory module |
| C7845-67901 |
Memory - 32MB, 100-pin SDRAM DIMM memory module |
| C7845A |
Memory - 32MB, 100-pin SDRAM DIMM memory module |
| C9121-67901 |
Memory - 128MB, 100-pin SDRAM DIMM memory module |
| C9121A |
Memory - 128MB, 100-pin SDRAM DIMM memory module |
| D4838A |
Memory - Font DIMM - Korean Font memory DIMM |
| Q1887-67901 |
Memory - 64MB SDRAM - 100MHz synchronous DRAM - DIMM package |
| Q1887A |
Memory - 64MB, 100-pin SDRAM DIMM memory module |
| Q2449-67907 |
Memory - Firmware DIMM memory - 4MB Flash/16MB SRAM combo memory DIMM |
| Q2449-67908 |
Memory - Firmware DIMM memory - 4MB Flash/16MB SRAM combo memory DIMM |
| Q2451-67905 |
Memory - Firmware DIMM memory - 4MB Flash/32MB SRAM combo memory DIMM |
| Q7707AX |
Memory - 32MB, 100-pin SDRAM DIMM memory module |
| Q7708-67951 |
Memory - 64MB SDRAM - 100MHz synchronous DRAM - DIMM package |
| Q7709-67951 |
Memory - 133 MHz 128MB, 100-pin SDRAM DIMM memory module Synchronous DRAM DIMM |
| Q7709A |
Memory - 133 MHz 128MB, 100-pin SDRAM DIMM memory module Synchronous DRAM DIMM |
| Q7709AX |
Memory - 133 MHz 128MB, 100-pin SDRAM DIMM memory module Synchronous DRAM DIMM |
| Q9121A |
Memory - 128MB, 100-pin SDRAM DIMM memory module Synchronous DRAM DIMM |
| RH7-1428-000CN |
Motor - Main motor - Drives gears in main drive assembly |
| RB2-1790-000CN |
Mount - Sensor mount for HP LaserJet 5000 Series |
| C4110-40004 |
Overlay - LaserJet 5100 control panel overlay (English) |
| RF5-4117-000CN |
Pad - Pad assembly for HP LaserJet 5000 Series |
| RF5-4119-000CN |
Pad - Tray 1 separation pad - Does not include holder |
| RF5-4120-000CN |
Pad - Separation pad assembly (Does not include the spring) - Mounts toward the front of the 250-sheet paper cassette tray assembly |
| J3111-69001 |
PC Board - JetDirect 600N EIO internal print server 10Base-T, 10BASE-2, and LocalTalk LAN interface board - Has one RJ-45, BNC, and 8-pin DIN connector;Click to order the functional equivalent: J4135-61001 |
| J4167-69001 |
PC Board - JetDirect 600N EIO internal print server token ring LAN interface board - Has one RJ-45 and DB-9 connector |
| Q1860-67901 |
PC Board - Formatter PC Board |
| Q1860-69001 |
PC Board - Formatter PC Board |
| Q1860-69018 |
PC Board - DC Controller PC Board |
| Q1860-69019 |
PC Board - DC Controller PC Board |
| RG5-2125-000CN |
PC Board - Feed sensor/paper size board - Small PC board with four paper size micro-switches and the paper feed photo sensor - Mounts in the front left of the 250-sheet paper feeder assembly |
| RG5-4212-000CN |
PC Board - Sensor PCA - Tray size sensor PCA - Has four micro switchs acuated by the tray size sensor leaf spring |
| RG5-4212-020CN |
PC Board - Sensor PCA - Tray size sensor PCA - Has four micro switchs acuated by the tray size sensor leaf spring |
| RG5-7057-070CN |
PC Board - DC Controller PC Board |
| RG5-7058-000CN |
PC Board - Paper handling PCA |
| RG5-7196-000CN |
PC Board - Paper size detection assembly - Detects paper size of tray used in 500 sheet feeder assembly |
| RG5-7197-000CN |
PC Board - Paper feed controller PCA assembly - For 500 sheet paper feeder assembly |
| J6057AR |
PC Board Interface - JetDirect 615N internal print server (10Base-T and 100Base-TX) LAN interface board - Plugs into peripheral EIO slot - Has a RJ-45 connector - Comes with software on CD-ROM and manual |
| J6057AR |
PC Board Interface - JetDirect 615N internal print server (10Base-T and 100Base-TX) LAN interface board - Plugs into peripheral EIO slot - Has a RJ-45 connector - Comes with software on CD-ROM and manual |
| J7934G |
PC Board Interface - HP JetDirect 620n internal print server - 10BaseT and 100BaseTX LAN interface board - Plugs into peripheral EIO slot - Has an RJ-45 connector - Comes with software on CD-ROM and manual on CD-ROM |
| RB2-1745-000CN |
Pin - Front cover pin - Hinge pins for drop down front cover (price is for one hinge pin, order accordingly). |
| RB1-6141-000CN |
Plate - Grounding plate |
| RB2-1734-000CN |
Plate - Grounding plate |
| RB2-1735-000CN |
Plate - Grounding plate |
| RB2-1736-000CN |
Plate - Grounding plate |
| RB2-1990-000CN |
Plate - Grounding plate |
| RB3-0352-000CN |
Plate - Fan grounding plate and fan housing |
| RG5-7074-000CN |
Plate - Grounding plate |
| Q1860-69006 |
Power Supply - Power Supply Assembly (for 100V/120V Operation) |
| Q1860-69007 |
Power Supply - Power Supply Assembly (for 220V/240V Operation) |
| RH3-2248-000CN |
Power Supply - Power Supply Assembly (for 100V/120V Operation) |
| RH3-2249-000CN |
Power Supply - Power Supply Assembly (for 220V/240V Operation) |
| J3111-61001 |
Print Server - JetDirect 600N EIO internal print server 10Base-T, 10BASE-2, and LocalTalk LAN interface board - Has one RJ-45, BNC, and 8-pin DIN connector |
| J4167-61001 |
Print Server - JetDirect 610N token ring LAN interface board - DB-9 and RJ-45 connectors |
| J6057-69001 |
Print Server - JetDirect 615N internal print server LAN interface board - 10Base-T and 100Base-TX - Plugs into peripheral EIO slot, has RJ-45 connector. |
| J6057-69011 |
Print Server - JetDirect 615N internal print server LAN interface board - 10Base-T and 100Base-TX - Plugs into peripheral EIO slot, has RJ-45 connector. |
| J6057A |
Print Server - JetDirect 615N internal print server LAN interface board - 10Base-T and 100Base-TX - Plugs into peripheral EIO slot, has RJ-45 connector |
| J7934-69001 |
Print Server - JetDirect 620N Ethernet Print Server, internal print server LAN interface board - 10Base-T and 100Base-TX - Plugs into peripheral EIO slot, has RJ-45 connector. |
| J7934A |
Print Server - JetDirect 620N Ethernet Print Server, internal print server LAN interface board - 10Base-T and 100Base-TX - Plugs into peripheral EIO slot, has RJ-45 connector. |
| RF5-2397-000CN |
Rail - Tray 2 left rail - Left side tray support |
| RF5-2398-030CN |
Rail - Tray 2 right rail - Right side tray support |
| RG5-3545-000CN |
Receptacle - Power inlet assembly - A/C input and power switch |
| Q1860A-Repair_LaserJet |
Repair Service - Ship your product to us for a small diagnostic fee; and a professional service job. We will contact you with repair total and your diagnostic fee will be waived if unit is repaired. Service warranty is 30days labor and 90days for parts. Extended warranty option is available. |
| RB2-1731-000CN |
Rod - Switch rod - Mechanical link between on/off switch lever and electrical on/off switch at power inlet assembly |
| RB1-6251-000CN |
Roller - Lower delivery roller - Presses against the lower delivery roller shaft assembly |
| RB1-7499-000CN |
Roller - Feed roller assembly - Full width shaft with four rubber rollers on it - Mounts in front of the paper pickup roller on the 250-sheet paper feeder assembly base unit |
| RB1-8865-000CN |
Roller - Paper pickup roller (D-shaped) - Sold individually |
| RB2-1820-020CN |
Roller - Pickup roller - Tray 1 pickup roller |
| RB2-1820-040CN |
Roller - Pickup roller - Tray 1 pickup roller |
| RB2-1821-020CN |
Roller - Paper pickup roller assembly (D-shaped) - Rubber roller on a plastic frame - Locks on to the paper pickup shaft in the 250-sheet paper feeder assebmly base unit |
| RB2-1821-030CN |
Roller - Paper pickup roller assembly (D-shaped) - Rubber roller on a plastic frame - Locks on to the paper pickup shaft in the 250-sheet paper feeder assebmly base unit |
| RB2-1985-000CN |
Roller - Lower output delivery roller - Shaft with four rollers |
| RB2-1998-000CN |
Roller - Roller - Upper roller of face-down roller guide - 4 used |
| RB2-3232-000CN |
Roller - Feed roller - Shaft with round rollers that moves paper after pickup roller on 500 sheet feeder assembly |
| RF5-2634-000CN |
Roller - Feed roller - Moves paper after pickup roller |
| RF5-2636-000CN |
Roller - Pickup roller assembly - Picks paper out of tray |
| RG5-3519-000CN |
Roller - Pickup roller assembly - Shaft/roller assembly that feeds paper from paper input assemblies - Also order separation pad kit |
| RG5-3519-020CN |
Roller - Pickup roller assembly - Shaft/roller assembly that feeds paper from paper input assemblies - Also order separation pad kit |
| RG5-3519-070CN |
Roller - Tray 1 pickup roller assembly - Shaft/roller assembly that feeds paper from paper input assemblies - Also order separation pad kit |
| RG5-3521-020CN |
Roller - Tray 2 paper pickup roller assembly |
| RG5-3521-040CN |
Roller - Tray 2 paper pickup roller assembly |
| RG5-3542-000CN |
Roller - Upper delivery roller assembly - Paper output roller assembly - Includes right and left roller bushings, anti-static brush and delivery guide |
| RG5-3542-090CN |
Roller - Upper delivery roller assembly - Paper output roller assembly - Includes right and left roller bushings, anti-static brush and delivery guide |
| RG5-3644-030CN |
Roller - Pickup roller assembly - Includes the roller shaft with the paper pickup (D-shaped) roller, two hard plastic side cams, and bushings - Mounts in the top front of the 250-sheet paper feeder assembly base unit |
| RG5-4916-000CN |
Roller - Registration roller assembly |
| RG5-7084-000CN |
Roller - Paper feed roller assembly |
| RG9-1337-000CN |
Roller - Face down guide roller |
| RG9-1542-000CN |
Roller - Transfer roller assembly - Transfers static charge to the media being printed on |
| RB1-7503-000CN |
Sensor - Sensor spring - Spring plate with four fingers (which press against the four micro-switches on the paper size sensor board) - Mounts on the front left side of the 250-sheet paper feeder assembly base unit |
| RF5-4151-000CN |
Sensor - Tray sensor assembly |
| RG5-3553-000CN |
Sensor - Rear door sensor assembly - Arm and mount assembly |
| WG8-5375-000CN |
Sensor - Paper sensor for HP LaserJet 5100 Series |
| Q1860A-Manual_Laser |
Service Manual - Printer Service Manual - Includes troubleshooting, error messages, paper jams, parts and parts diagrams. |
| 9222-1185 |
Service Parts - 9222-1185 |
| WG8-5362-000CN |
Shaft - Photo-sensor (TLP1241) - Sensor flag activated. |
| RH7-5235-000CN |
Solenoid - Tray 1 paper pickup solenoid - SL404 |
| RH7-5236-000CN |
Solenoid - Cassette paper pickup solenoid - SL306 |
| RB2-1739-000CN |
Spring - Door switch spring - Provides tension for toner door switch |
| RB2-1759-000CN |
Spring - Control panel leaf spring |
| RB2-1783-000CN |
Spring - Paper sensor lever spring |
| RB2-1784-000CN |
Spring - Paper sensor lever spring - Holds tension on sensor arm |
| RB2-1808-000CN |
Spring - Lever spring - Provides tension for paper sensor flag |
| RB2-1825-000CN |
Spring - Leaf spring - Tray size sensor fingers |
| RB2-2076-000CN |
Spring - Delivery roller spring - Provides tension for lower delivery roller (four used) |
| RS5-2225-020CN |
Spring - Face down guide roller torsion spring |
| RS5-2434-000CN |
Spring - Tray 2 shaft gear spring - Holds tension on shaft hook |
| RS5-2439-000CN |
Spring - Compression spring - Provides tension for the separation pad in the 250-sheet paper cassette tray assembly |
| RS5-2441-000CN |
Spring - Compression spring - Provides pressure for Tray 1 paper guide plate |
| RS5-2632-000CN |
Spring - Tension spring - Provides tension for pickup roller |
| RB2-2023-000CN |
Stop - Paper stop (Blue plastic) - Paper length adjustment stop plate |
| RB2-1977-000CN |
Strap - Tray support strap - Supports rear drop down output tray |
| RB2-1732-000CN |
Switch - Door switch - Indicates when toner door is ajar |
| RB2-1744-000CN |
Switch - On/off switch for HP LaserJet 5000 Series |
| C4117-69001 |
Tray - 500 sheet universal paper tray |
| RG5-3552-060CN |
Tray - Face up tray assembly - Drop down output tray with extension |
| RG5-7164-060CN |
Tray - 500 Sheet paper tray - 500 Sheet universal replacement paper cassette |
| RG5-7188-020CN |
Tray Assembly - 250-sheet paper cassette tray assembly - Includes the paper tray assembly with the separation pad, paper width adjusters, and rear paper stop |
Techical Help
View service parts