HP parts list for CH109A Scitex FB950

CH971-62824 Accessory - Adhesive backed ruler - English metric ruler - 2.5m (98-inches) long and can be cut down for the 1.6m (64-inches) size - This is the ruler located with the N-up alignment pins

CH971-63114 Accessory - High Density Polyethylene (HDPE) funnel - 32Oz capacity - Facilitates emptying ShopVac waste ink into waste ink bottle

CH971-56881 Accessory Kit - Accessory kit for the support tables - Includes all the fasteners, casters, etc needed to assemble two tables - For use with the Scitex FB910/FB950 printers

CH109-67003 Actuator - Lift motor (actuator) - Used for all up/down component movement in the printer - This motor is used in nine locations on the printer

CQ114-67068 Actuator - Lifting Actuator for the Rail (FRM RAIL UP/DOWN MTR UQ) designed for HP Scitex FB500 FB550 FB700 FB750 and FB950 industrial printers. This motorized component operates the upward and downward movement of the rail with two units typically used per printer.

CQ114-67094 Actuator - 75mm stroke actuator assembly - This is the actuator and all associated bracketry and hardware plus the lift encoder reader and strip - Used for the input and output media hold-down rollers and the alignment bar - For the Scitex FB500/FB700/FB950 printers

CH154-50002 Bar - Ionizer bar - Includes the bar with cable only - Attaches to the input side of the rail - For use with the Scitex FB950 printer

CH971-57513 Bar - Bar media guide - This bar is lowered down to stop and square the media

CH971-91490 Bar - Y-axis alignment bar - Includes fine-thread screws for adjusting the Y-axis alignment of the printheads - Located in front of the printheads

CQ115-67012 Bar - Anti-static ionizer bar - For the Scitex FB700 printers

CH154-67003 Belt - Main carriage drive belt (Blue) - For use with Scitex FB950 printers

CH971-90710 Belt - Carriage drive timing belt - Located between the carriage drive motor and the carriage drive shaft. Carriage Drive Timing Belt For HP DJ H35100 H35500 H45500 H45100 and similar Scitex Designjet model family types.

CH971-91462 Belt - Media belt - Includes all the support pieces and accessories used to change the belt - For use with the Scitex FB950/FB910 printers

CH971-91530 Belt - Drive belt - Used for the service station wiper motion

CH971-91400 Blower Assembly - Belt vacuum blower assembly - Includes one blower - Used to suck down media to belt - For the FB500/FB700/FB950/FB910

CQ114-67238 Blower Assembly - Frmblwrblt Vacalt HP SCITEX FB500 FB700 FB910 FB950 GENUINE

CH154-67014 Bottle - Waste ink bottle - One gallon bottle with warning label for collection of UV liquid wastes

CH154-67015 Bottle - Flush bottle - Squeeze bottle with label for UV flush

CJ848A Box - Electronics assembly (ebox assembly) - For use with the Scitex FB950

CH108-60008 Bracket - L-bracket and internal mechanical - Located on the on the output, user end of the printer - Includes the parts that transfer take-up motor power to the take-up spool (does not include the motor/switch assembly, the takeup drive belt, or the belt cover)

CH108-60009 Bracket - L-bracket - Located on the output, service end of the printer

CH108-60010 Bracket - L-bracket - Located on the input, user end of the printer - Holds the supply roll and inactive foam rollers

CH108-60011 Bracket - L-bracket - Located on the input, service end of the printer - Holds the supply roll and inactive foam rollers

CH971-57219 Bracket - Carriage drive bracket - For use with Designjet H series and Scitex FB910/FB950 printers

CH971-57259 Bracket - Service-end bracket - Supports the lift and press rollers in the roll-to-roll option

CH971-62665 Brush - Brass wire brush - Used to clean the ionizer bar

CQ114-67180 Brush - Ionizer brush - Used to clean the points on the anti-static ionizer bar

CH971-62205 Bumper - Polyurethane rubber bumper - 7/16-inch diameter x 13/64-inch thick round, adhesive-backed bumper - Used on some platforms on the rail at the carriage home, or as a spacer on the headboard-end of the LVDS cable (on Scitex FB500/FB700 printers only)

CH971-91398 Button - Emergency stop button - For use with Scitex FB950/FB910 printers

CH154-67009 Cable - UV lamp power cable - Cable goes from the electronics assembly to one lamp - For use with Scitex FB500/FB700/FB950

CH971-50014 Cable - Cable assembly - Braided ribbon cable from OHS board to I/O board - For the Scitex FB500/FB700/FB910/FB950 printers

CH971-50028 Cable - Cable - Goes from the three pin sabre connector on the AC distribution board to an AC receptacle

CH971-50116 Cable - Cable - Goes from the AC filter to the power distribution board

CH971-50148 Cable - Cable assembly - Cable between the headboard and the UV lamp - For the Scitex FB950 and the Designjet H-Series

CH971-50163 Cable - Cable harness - Goes from the OHS board to the ink pumps

CH971-50284 Cable - Cable - Goes from the UV power supply to the external connector for the UV lamp cable found on the top side of the electronics box

CH971-50286 Cable - Cable assembly - 2-wire cable - Ties in to the power cable for the UV lamp cable receptacle on the exterior of the electronics box

CH971-50289 Cable - Cable assembly - 2-wire cable - Ties in to the power cable for the UV lamp cable receptacle on the exterior of the electronics box

CH971-50299 Cable - Cable assembly - Goes from the power distribution board to the external receptacle for take-up motor power

CH971-50300 Cable - Internal ebox cable - Goes from the AC distribution board to the UVPS and AC relay - Has a 4-pin molex sabre connector for the AC distribution board connection

CH971-50316 Cable - Camera fans cable - Goes from the upper HDBD connector to the rear carriage fans

CH971-50322 Cable - Cable assembly - Goes from the headboard to the carriage home sensor

CH971-50354 Cable - Internal ebox cable assembly - Cable that goes from the I/O board J28 to AC relays, cooling fans, main power switch, foot pedal, and UV cable-present sensor

CH971-50364 Cable - Cable assembly - 2-wire cable - Goes from the UV power supply to the cable harness from the I/O board

CH971-50404 Cable - Cable assembly - Goes from the lower HDBD connector to the front carriage fans and color sensor fan

CH971-52323 Cable - Cable - Used to connect the printer directly to a print server - For use without a hub

CH971-55682 Cable - Cable assembly - Goes from the I/O board to the motor control board

CH971-57303 Cable - Cable - Goes from the headboard to the air valve assembly

CH971-57465 Cable - Cable - Goes from the external power receptacle for the ionizer power supply to the I/O board and power distribution board

CQ114-67051 Cable - Serial data cable - Touch-sensitive data transmission cable - Located between the LCD control panel and the I/O board

CQ114-67052 Cable - VGA cable - Located between the LCD control panel and the motherboard - For the video display

CQ114-67128 Cable - LVDS data cable - For use with the Scitex FB950 printer

CQ114-67243 Cable - Frm-Fb500/700-Igus-Data-Cable

CH971-91605 Camera - Camera assembly - For use with Scitex FB950 and the Designjet H-series

CH971-57560 Cap - End cap sheet metal - Located on the service end of the printer - For use with the Scitex FB950 printer

CH971-91589 Cap - Printhead cap - Used to cap a printhead port or similar luer fitting location

CH971-91590 Cap - Tube cap - Used to cap the end of the luer fitting that normally connects to the ink tube

CH971-91497 Carriage - Carriage headboard assembly - For use with the Designjet H-Series and Scitex FB950 printer

CH971-91502 Carriage - Carriage drive assembly with bracket - For use with Scitex FB950/FB950 and Designjet H series

CQ114-67109 Carriage - Carriage drive assembly - Includes bracket, motor, drive shaft, timing belt, and all related fasteners - For the Scitex FB500/FB700 printer

CH971-57723 Clamp - Clamps - Does not in include the fastener - Secures the main (Blue) drive belt to the (Black) clips in the carriage

CH151A Cleaner - lamp filters is suitable for HP FB950 printers. This is HP original part (number CH151A). Each filter is 14.3cm long 8.3cm wide and 0.3cm thick.

CH154-67045 Clip - Clip assembly - Includes one unit, does not include the taller luer cap required for use with the clamp - Used on the printhead ink U-tubes - For use with Designjet H-series and Scitex FB950

CH971-91001 Clip - Clip - Connected to the trolley and provides attachment points for the carriage drive belt on both ends

1500-1274 Collar - Internal clamping collar - 25mm diameter - Used on the ends of the media drive idle roller shaft - For the Scitex FB910/FB950/FB500/FB700 printers

CH971-91264 Collar - Spool-holding collar - Attaches to the stand on the left side take-up and supply postions (when facing front of printer)

CH971-91265 Collar - Spool-holding collar - attaches to the stand on the right side take-up and supply postions (when facing front of printer)

CH971-57327 Connector - Complete ink tube/filter/connectors assembly - Used with the ink boxes - For use with Scitex FB950/FB500/FB700 and Designjet H (CS 5400uv) printers

CH971-91634 Coupler - Off-Head Supply (OHS) ink coupler - Includes one coupling and the nut used to secure it on the printer - This is the quick-disconnect attachment for the ink boxes and receives the connector from the inkbox pigtail

CH154-60033 Display - LCD display assembly - For use with Scitex FB950 printers only

CH154-67038 Drive Assembly - Hard disk drive (HDD) - Used in the electronics assembly - For use with the Scitex FB950 printer

CH154-00013 Enclosure - Belt/roller enclosure - Located on the output-side of the user-end

CH154-67012 Enclosure - Window enclosure - Includes pushnuts - Replacement UV-blocking windows used only on the center output-side door - For the Scitex FB500/FB700/FB950

CH971-57557 Enclosure - Central top enclosure assembly - Includes the window material and fasteners - Located on the input side of the printer

CH971-57559 Enclosure - Full enclosure skins - For use on the user side of the printer - For use with the Scitex FB950 printer

CH971-57580 Enclosure - Central top enclosure assembly - Includes all fans, windows, light blocking skirt, and required fasteners - Located on the output side of the printer (top cover that can be opened)

CH971-57585 Enclosure - Belt/roller enclosure - Located on the user-end (input-side)

CH971-57586 Enclosure - Belt/roller enclosure - Located on the service-end (input-side)

CJ856A Enclosure - Carriage cover enclosure - Includes the fans - For use with the Scitex FB950 printer

CH154-67005 Encoder - Encoder strip actuator assembly - Includes bracket - Used in all lifting assemblies and service station - For the Scitex FB950 printer

CH154-67040 Encoder - High-resolution on-shaft encoder - Used for media drive motion - For use with the Scitex FB950 printer

CH971-90708 Encoder - Encoder reader assembly - Located on the back of the carriage assembly

CH971-91407 Encoder - Media drive encoder - Attaches to the belt drive motor on the service end of the printer - Does not include the high-resolution encoder - For the Scitex FB500/FB700/FB950/FB910

CH971-91425 Encoder - Mylar encoder strip and foam tape - It is long enough for a 2.5m (98-inch) printer and can be trimmed down for smaller printers - Part requires you to reuse the existing aluminum bar from the old strip

CH154-67010 Fan - Cooling fan - Used on the carriage (all four locations) and the Designjet H image sensor - For use with Scitex FB950 printers only

CH971-91513 Fan - Fan assembly - Cools the electronics box in the printer

CH971-91596 Fan - UV lamp housing cooling fan - For the Scitex FB500/FB700/FB950, and Designjet H-series printers

CH971-91599 Fan - Fan assembly - Located on the top enclosure and end enclosures - For the Scitex FB500/FB700, also the Designjet H-Series

CH104-67020 Filter - Tube/filter/fitting assembly - Used between the printhead and the air manifold

CH108-60004 Filter - Large cylindrical air filter - Located on the exterior of the vacuum assembly

CH971-60050 Filter - AC filter - Located inside the electronics assemblies - For use with Scitex FB910/FB950 printers

CH971-91504 Filter - Ink filter - 1.74-inch diameter - Can be used with any ink color - This filter is used in the OHS area of the printer - For use with Scitex FB950 and Designjet H-Series

CH971-91644 Filter - Replacement filter - Includes media and mesh used inside the ShopVac, as well as related fasteners - For the Scitex FB500/FB700 printers

CQ114-67188 Filter - Replacement filter - Includes media and mesh used inside the ShopVac, as well as related fasteners - For the Scitex FB500/FB700 printers

CH971-91594 Glass Assembly - Quartz lamp glass - Inserts below the left or right lamp housing - For the FB500/FB700/FB950 also the Designjet H-Series

CH154-00020 Guard - Media belt edge guard - Located on the user side - For use with the Scitex FB950 printer

CH154-00021 Guard - Media belt edge guard - Located on the service side - For use with the Scitex FB950 printer

CH971-57318 Guard - Finger guard - Located on the service-end (input-side) over the belt on engines without the roll-to-roll option

CH971-57605 Guard - Finger guard - Includes a white media alignment fence on engines without the roll-to-roll option - Located on the user-end (input-side)

CH971-57691 Guard - Finger guard with media alignment fence (White) - Located on the user-end (input-side) engines without the roll-to-roll option

2232-M3991 Hardware - Carriage drive motor - For Scitex printers Scitex Color Span Carriage Drive Motor unit. Ametek Pittman 2232-M3991 DC Motor 60V 6000 RPM 30 oz-in

CH154-60013 Hardware - Float switch assembly - Includes brackets - Used in the service station - For the Scitex FB500/FB700/FB950 printer

CH154-67001 Hardware - Complete trolley assembly - Includes upper and lower plates - For use with Scitex FB950 printers

CH154-67013 Hardware - Light-blocking skirt - Used for the main cover - For use with Scitex FB950 printer

CH154-67034 Hardware - Track assembly - For use with the Scitex FB950 printer

CH154-67043 Hardware - ShopVac vacuum - 8-liter capacity - Compatible with all vintages of the Scitex FB950 printer - When installing this part on some vintages, a power cable (included) must be replaced

CH971-62547 Hardware - Luer fitting (White) - 1/8-inch, male-taper - Used on the ink tubing

CH971-62550 Hardware - Luer fitting (White) - 3/32-inch, male-taper - Used on the ink tubing

CH971-90811 Hardware - Carriage drive motor - For Scitex printers Scitex Color Span Carriage Drive Motor unit. HP Scitex Fb950 500/700 550/750 Carriage Drive Motor

CH971-91414 Hardware - Side alignment fence - Attached to belt assembly

CH971-91491 Hardware - Manifold assembly - Includes six valves that mounts on the rear of the carriage above the trolley

CH971-91531 Hardware - ShopVac vacuum - 8-liter capacity - Compatible with all vintages of the Scitex FB950 printer

CH971-91544 Hardware - Ink pump - Includes the tubing, fitting, and torx fasteners for installation

CH971-91598 Hardware - ShopVac vacuum - 8-liter capacity - Compatible with all vintages of the Scitex FB950 printer

CH976-00148 Hardware - Check valve assembly (White) - Used in the Off-Head Supply (OHS) - Color-coded for Light Cyan

CH976-00149 Hardware - Check valve assembly (Black) - Used in the Off-Head Supply (OHS) - Color-coded for Black

CH976-00150 Hardware - Check valve assembly (Red) - Used in the Off-Head Supply (OHS) - Color-coded for Magenta

CH976-00151 Hardware - Check valve assembly (Green) - Used in the Off-Head Supply (OHS) - Color-coded for Light Magenta

CH976-00152 Hardware - Check valve assembly (Blue) - Used in the Off-Head Supply (OHS) - Color-coded for Cyan

CH976-00153 Hardware - Check valve assembly (Yellow) - Used in the Off-Head Supply (OHS) - Color-coded for Yellow

CJ860A Hardware - Cabling loom (conduit and cables) - Used between the electronics assembly and devices on the service end of the printer

CJ861A Hardware - Cabling loom (conduit and cables) - Used between the electronics assembly and devices on the user end of the printer (excluding devices in the user-end removable enclosure)

CJ862A Hardware - Cabling loom (conduit and cables) - Used between the electronics assembly and devices in the user-end removable enclosure

CQ114-67073 Hardware - Float switch assembly - Includes brackets - Used in the service station - For the Scitex FB500/FB700/FB950 printer

CH154-60008 Holder - Carriage restraint - Includes all components - Used for shipping

CQ115-67047 Housing - Service-side lamp housing - Does not include bulb - For the Scitex FB700/FB950

CQ115-67048 Housing - User-side lamp housing - Does not include bulb - For the Scitex FB700/FB950. identifies the User-side (Right) UV Lamp Housing for specific HP Scitex industrial printers.

CH971-91595 Idler - Idler assembly - Located on service-end of the rail - For use with Scitex FB910/FB950 and the Designjet H-series

CH154-67016 Kit - Hardware kit - Includes the hose, spigot, and related hardware from service station basin to printer enclosure

CH154-67033 Kit - Repacking kit - Materials to repack plotter - For use with Scitex FB950 printers

CH154-67042 Kit - Hardware kit - This is the one-time field modification kit to install a complete set of six air tube assemblies with ink-blocking filter onto the carriage - For use with the Scitex FB950 printer

CH154-67044 Kit - Hardware kit - Includes 12 clip assemblies and 12 taller luer caps - For use with the Designjet H-series and Scitex FB950

CH971-91602 Kit - Ink line and fittings kit - Includes 24-inch UV ink tubing and an assortment of color-coded luer fittings

CH154-67091 Lamp - UV bulb/lamp - For use with Designjet H-Series and Scitex FB950/FB500/FB700 printers

CH109-67002 Lubricant - Oil-saturated cloth - Used for lubricating the carriage rail - For use with Scitex FB500/700/FB950, and H-Series printers

CH971-90854 Maintenance Kit - Grease kit - Used to lubricate gritroll bearings, media drive worm gear, and up/down threads of the media hold-down roller

CH971-91089 Media - Media spool collet - 3-inch in size - Can be hand tightened and loosened around the steel media spool

CH154-67008 Motor - Media drive motor/reducer assembly - For the Scitex FB950/FB500/FB700 printer

CH971-91533 Motor - Service station wiper motor - Moves the wiper head in the Y axis - For the Scitex FB500/FB700/FB950, also the Designjet H-Series

CH971-91561 Motor - Takeup motor and switch assembly - Used for the roll-to-roll accessory - For the Scitex FB500/FB700/FB910/FB950

CH971-62834 Mount - Flush panel mount - Recessed plastic hand-hold as used in the enclosures - For the Scitex FB910/FB950/FB500/FB700

CH971-91405 Pad - Leveling pad - For Scitex FB500/FB700/FB950/FB910 printers

CH154-00004 Pan - Light blocking pan - Located over the OHS area - For use with the Scitex FB950 printer

CH154-67035 PC Board - Motherboard assembly - For use with the Scitex FB950 printer

CH154-67041 PC Board - Formatter - Software version 4.20 - For use with the Scitex FB950 printer

CH971-91389 PC Board - Motor driver board (motor control board) - Located in the electronics assembly - For the Scitex FB500/FB700/FB91O/FB950 printers

CH971-91450 PC Board - Power Distribution board - Regulates the 3-phase power going into the printer

CH971-91542 PC Board - Main controller board - Used for the Off-Head Supply (OHS) - Has sockets for the profilers. For HP Scitex FB950 HP DesignJet H35100 H35500 H45100 H45500 and similar series.

CJ855A PC Board - I/O board - For use with the Scitex FB950 printer

CH971-91402 Pin - Alignment pin assembly - These pins are used to set position of multiple sheets - For the Scitex FB500/FB700/FB950/FB910

CH154-67002 Plate - Upper trolley plate assembly - For use with Scitex FB950 printers only

CH109-50001 Power Cord - 3-phase power cord - For use with plotters (Europe)

CH971-56213 Power Cord - Main AC power cord - For use with Scitex FB910/FB950 printers

CQ114-67046 Power Cord - Headboard power cord - Located in the track from the electronics assembly to the headboard - For use with the Scitex FB500/FB700/FB950

CH154-67011 Power Supply - UV power supply - For one channel of the lamp system - For use with Scitex FB950 printers

CH971-60068 Power Supply - Mini power supply (24VDC) - Powers the ink system vacuum pump only - For use with Scitex FB950 and Designjet H printers

CH971-90826 Power Supply - ATX power supply - Output voltage 12VDC - Located in the main electronics box

CH971-91083 Power Supply - Power supply and power plug adapter kit - Needed to implement the external auxiliary power source for IDS vacuum

CH971-91618 Power Supply - Ionizer power supply - For replacement of the Simco-branded ionizer-bar power supply only

CJ854A Power Supply - Dual charge power supply - Output voltage 24/38VDC - For use with the Scitex FB950 printer

CH104-67002 Pressure Assembly - Vacuum/pressure assembly - Pressure pump for the Ink Delivery System (IDS) - Located on the OHS assembly

CH971-91543 Pressure Assembly - Vacuum pressure assembly

CH971-91493 Printhead - Master printhead - Does not include any thermistors - Used on any location of the printer - For use with Scitex FB950 and any model of the Designjet H series

CH154-67006 Reader - Encoder reader board - Does not include the metal bracket - This assembly is used on all of the lifting positions - For the Scitex FB950/FB500/FB700 printer

CH971-50021 Receptacle - External AC-input receptacle (Blue) - Includes the cable from the receptacle to the AC filter

CH971-91626 Regulator - Regulator - Used in the Vacuum Pressure (VP) assembly

CH971-91586 Relay - AC relay - Located in the main electronics box

CH104-67001 Reservoir - Printhead reservoir kit - For use when there is a reservoir leak, fitting problem, or other printhead issues, where jetting is not the problem - For use with any of the piezo-printhead engines

CH971-57266 Reservoir - Vacuum reservoir - This is a portion of the ink system vacuum - For use with Designjet H series and Scitex FB950 printers

CH154-20015 Roller - Media drive roller - Located on the output side of the engine - For use with the Scitex FB950 printer

CH154-20016 Roller - Media drive roller - Located on the output side of the engine - For use with the Scitex FB950 printer

CH971-57296 Roller - Foam-covered metal roller - Used in two places in the roll-feed supply system - For use with Scitex FB910/FB950 printers

CH971-57520 Roller - Media hold-down roller assembly - Located on both input or output sides - For use with the Scitex FB950 printer

CH971-91603 Roller - Bearing media roller

CH971-60085 Sensor - Carriage home sensor - For use with Scitex FB950 printer

CH971-62685 Sensor - Bracket height adjustment sensor - Mounting bracket for the alignment sensor that confirms that the media is straight before the pinch roller goes down

CH971-91028 Sensor - Service station sensor - This is the home sensor for the wipers

CH971-91406 Sensor - Media thickness sensor assembly - Calibrated in the factory - For the Scitex FB950/FB910/FB500/FB700 printer

CQ114-67023 Sensor - Optical media-out detection sensor - Located on the input side of the printer - Two are used on the printer, one at center and one at the user end - For the Scitex FB500/FB700/FB950 printer

CJ857A Service Station - Service station assembly - For use with the Scitex FB950 printer

CQ114-67110 Shaft - Carriage drive shaft - Shaft is knurled to prevent pulley from slipping on the shaft - For the Scitex FB500/FB700/FB910/FB950 printer

CH154-67031 Slider - Vertical slide - Located on the service station - If broken, this can be replaced alone without requiring replacement of the entire service station assembly

CH971-91258 Spindle - Media spool - Includes two 3-inch collets - For use with 98-inch printers

CH971-91558 Spindle - Media spool - Does not inlcude collets - For use with 98-inch printers

CH971-63071 Spring - Gas springs - Used to hold open the main cover on - For use with the Scitex FB950 printer

CH971-56880 Support - Media support table - For use with the Scitex FB910/FB950

CH154-67037 Switch - Replacement foot switch - Orange safety hood not included - For the Scitex FB700/FB950/FB910 and H-Series

CH971-91444 Switch - Switch - Configures the power distribution board for the type of 3-phase power used at the site - This switch must be set correctly before power is applied to the printer, or serious damage can occur to the printer

CH971-91469 Switch - On/Off switch - Located on the electronics assembly - For the Scitex FB500/FB700/FB950/FB910 printers

CH971-91576 Switch - Door switch - Used ont the cover-open detect - For use with Designjet H-series printers

CQ115-67002 Switch - Frm Foot Switch U

CQ115-67051 Tape - Foam tape - 175cm (69-inch) long - Located on top of the rail that cushions the track assembly (Igus) - This length is for any 2.5m (98-inch) printer, but may be cut down to shorter lengths for use on other machines

CH971-91562 Tensioner - Supply tensioner - Used on the user-input bracket, for use with the supply and take-up system - For use with Scitex FB910/FB950 printers

CH971-91492 Thermistor - Thermistors kit - Includes two ink and one air temperature thermistor (they have been calibrated together and should be replaced together)

CH971-55984 Tool - Head height gauge tool - This go/no-go gauge is used to set the printhead height to 0.085-inches above the surface of the media

CH971-57693 Tool - Custom tool - Assists removing and installing the main drive belt connection to the carriage

CH971-91572 Tool - Belt tension tool kit - Fixture used to measure tension on the media belt - Requires a dial indicator (not included) - For the Scitex FB500/FB700/FB950/FB910

CH971-91631 Tool - Service tools kit - Kit includes the head height gauge, squeeze bottle (for flush), lint-free cloths, luer caps, and the carriage belt - For use with Scitex FB950 and the Designjet H-series

CH971-15183 Transformer - Step-down transformer (220VAC to 110VAC) - Used with the 110VAC ShopVac

CJ858A Tray - Vacuum fan tray - Includes the fans - Used for the pre-print (center) zone of the vacuum table - For use with the Scitex FB950 printer

CJ859A Tray - Input/output vacuum fan tray - Includes the fans - Used for both the input and output zones of the vacuum table - For use with the Scitex FB950 printer

CH154-67004 Tube - U-tube assembly - For air connection between any two UV printheads

CH154-67017 Tube - Long opaque tube (White) - For ink that runs through the track assembly - Luer fittings are color-coded for the light cyan ink channel

CH154-67018 Tube - Long opaque tube (Black) - For ink that runs through the track assembly - Luer fittings color-coded for the black ink channel

CH154-67019 Tube - Long opaque tube (Red) - For ink that runs through the track assembly - Luer fittings are color-coded for the magenta ink channel

CH154-67020 Tube - Long opaque tube (Green) - For ink that runs through the track assembly - Luer fittings are color-coded for the light magenta ink channel

CH154-67021 Tube - Long opaque tube (Blue) - For ink that runs through the track assembly - Luer fittings are color-coded for the cyan ink channel

CH154-67022 Tube - Long opaque tube (Yellow) - For ink that runs through the track assembly - Luer fittings are color-coded for the yellow ink channel

CH154-67023 Tube - Ink system vacuum tube - Runs through the track assembly - For use with Scitex FB500/FB700/FB950 printers

CH154-67024 Tube - Ink system pressure tube - Runs through the track assembly - For use with FB500/FB700/FB950

CH971-91227 Tube - U-tube - For use with ink between two printheads of a color

CH971-91499 Tube - Short UV ink tube - Connects to the printhead with a luer fitting and to the ink track tube with multi-colored luer fittings

CQ114-67221 Tube - Bucket tube - 10.90-inches (27.68 cm) length hose - Includes hose clamps for attachment - Located in the service station basin (bucket) between the wiper and the baffle - For use with Scitex FB500/FB700/FB950 printers

CH971-91344 Vacuum - Restrictor - For use with all vacuum/pressure assemblies

CH154-67030 Wiper - Wiper blade - For use with the Scitex FB950 printer - This is a different material than the H-Series wiper

HP Scitex FB950 printer (CH109A)

HP parts list for CH109A HP Scitex FB950 printer