Part |
Picture |
Description |
RB2-7927-000CN |
Glass mounting alignment clip - Used to properly align the copyboard glass in the scanner assembly cover frame - Mounts in the left rear corner of the frame (one used) |
RB2-7928-000CN |
Glass mounting clip - Used to retain the copyboard glass in the scanner assembly cover frame - Mounts in the left front, right front, and right rear corners of the frame (three used) |
RB2-7933-000CN |
Lower front cover - Bottom of the protrusion that makes up the control panel housing - Mounts to the front of the scanner assembly |
RB2-7934-000CN |
Upper front cover - Top of the protrusion that makes up the control panel housing - Mounts to the front of the scanner assembly |
RB2-7935-000CN |
Glass mount cover - Small plastic piece that covers the mounting hardware used to retain the copyboard glass - Mounts in the recesses on the scanner assembly upper front cover (two used) |
RB2-7939-000CN |
Tray rack arm - Strip of plastic with gear teeth molded into one side - Keeps the front and rear paper guides on the ADF input tray equidistant from the center (two used) |
RB2-7943-000CN |
Sensor lever - Rotating arm with a flag at one end that protrudes through the ADF base and another at the other end that activates one of the media length sensors - Mounts on the bottom center of the ADF base assembly (two used) |
RB2-7961-000CN |
Paper pickup roller (Only) - Rubber D shaped roller - Mounts on the paper pickup drive shaft in the bottom of the ADF paper pickup assembly |
RB2-7964-000CN |
ADF open flag - Quarter round plastic flag on a short arm - Activates the photo-sensor when the ADF assembly is open - Mounts on the front frame of the ADF paper pickup assembly |
RB2-7970-000CN |
Static charge eliminator - Comb that dissipates static charge as paper exits the ADF assembly - Mounts above upper delivery roller in the ADF paper pickup assembly |
RB2-7978-000CN |
Flag lever - Sensor activator half of the sensor flag for detecting when the ADF input tray is empty - Activates the sensor on the rear wall of the ADF paper pickup assembly |
RB2-7988-000CN |
Separation belt - Gray rubber belt between the separation drive shaft and the stationary shaft - Mounts towards the entrance of the ADF paper pickup assembly (four used) |
RB2-7989-000CN |
Support spacer - Used to keep the separation belts tight between the drive shaft and the stationary shaft in the separation assembly - Mounts in the ADF paper pickup assembly (three used) |
RB2-7990-000CN |
Spring holder - Small Black plastic piece that holds the leaf spring against the stationary shaft in each spacer in the separation assembly - Mounts in the ADF paper pickup assembly (three used) |
RB2-7991-000CN |
Leaf spring - Used to lock the spacer between the drive shaft and the stationary shaft in the separation assembly - Mounts in the ADF paper pickup assembly (three used) |
RB2-7999-000CN |
Weight plate (Only) - Black plastic plate that drops down during the paper pickup process and pushes against the paper stack on the pickup rollers - Mounts in the ADF paper pickup assembly |
RB2-8002-000CN |
Flag lever - Lever half of the sensor flag for detecting when the ADF input tray is empty - Flag part hangs down at the entrance to the ADF paper pickup assembly |
RB2-8015-000CN |
Release handle - Used to open the ADF main assembly from the paper pickup assembly to clear paper jams - Slides on the latching shaft in the top left center of the ADF main assembly |
RB2-8016-000CN |
Latching shaft - Long square shaft with a latching hook at one end - Used with the free release latch and release handle to secures the ADF main assembly when the unit is in the operating position |
RB2-8017-000CN |
Release latch - Curved plastic latch that slides on the latching shaft - Secures the ADF main assembly when the unit is in the operating position - Mounts on the front of the ADF main assembly |
RB2-8031-000CN |
Cable cover (Black plastic) - Covers and protects the cables on the front side of the ADF main assembly |
RB2-8040-000CN |
Top cover assembly - `U` shaped plastic cover - Covers the top of the scanner in the ADF assembly - Mounts on the left end of the ADF assembly |
RB2-8046-000CN |
Lower front cable guide (I/F 1) - One of six pieces that form the pivioting cable guide from the ADF assembly to the scanner assembly - Mounts on the left rear of the ADF assembly |
RB2-8047-000CN |
Upper front cable guide (I/F 4) - Curved plastic piece - One of six pieces that form the pivioting cable guide from the ADF assembly to the scanner assembly - Mounts on the left rear of the ADF assembly |
RB2-8048-000CN |
ADF assembly front cover - Mounts on the end of the ADF main assembly structure |
RB2-8054-000CN |
Left side cover - Serves as the mounting bracket for the ADF paper output tray - Mounts on the upper left side of the scanner assembly |
RB2-8060-000CN |
Connector cover - Small rectangular piece that extends out from the back of the scanner assembly (two used) |
RB2-8063-000CN |
Right side cover - 'L' shaped rectangular cover for the right end of the scanner assembly |
RB2-8121-000CN |
ETB socket - Socket that left side of ETB fits into |
RB2-8122-020CN |
Toner shutter gear - Opens toner shutters when the ETB is closed |
RB2-8124-020CN |
ETB socket - Socket that right side of ETB fits into |
RB2-8147-000CN |
Cartridge guide - Upper right side toner cartridge guides - For black and magenta cartridges |
RB2-8151-020CN |
Pressure arm for HP Color LaserJet 4600 Series |
RB2-8195-000CN |
Cartridge pressure lever |
RB2-8213-000CN |
Spring rod - Provides mechanical link for spring pressure to assist opening Tray1/MP tray - Two used |
RB2-8225-000CN |
Drum drive interlock plate |
RB2-8239-030CN |
Developer disengagement plate - Mechanical link that disengages developer from drum |
RB2-8246-000CN |
Laser scanner support spring - Supports laser scanner module - Three used |
RB2-8246-020CN |
Laser scanner support spring - Supports laser scanner module - Three used |
RB2-8250-000CN |
Test print arm - External test print button/rod |
RB2-8255-000CN |
Grounding plate - Provides ground for developer units |
RB2-8349-000CN |
Paper size arm - Senses paper size in paper tray - 3 used |
RB2-8386-000CN |
Separation pad support - Support that the Tray 2 separation pad mounts to |
RB2-8498-030CN |
Paper sensor flag in fuser assembly |
RB2-8532-000CN |
Guide cable for HP Laserjet products. |
RB2-8540-000CN |
Sensor support bracket - Black plastic piece that holds photo sensors PS12 and PS13 - This is the bracket ONLY |
RB2-8541-000CN |
Sensor cover - Metal cover for fuser photosensor assembly |
RB2-8542-000CN |
Grounding plate - Electrical ground connection for fuser sensor assembly |
RB2-8590-040CN |
Left cover - Left side of printer cover |
RB2-8591-000CN |
Side cover - Right side of printer cover |
RB2-8592-000CN |
Rear cover - Rear of printer cover |
RB2-8593-000CN |
Rear lower cover - Small plastic cover located below large rear upper cover |
RB2-8596-000CN |
Air filter on upper left side |
RB2-8597-000CN |
Air filter at top rear of printer - Formatter fan air filter |
RB2-8678-000CN |
Ferrite core assembly - Large 'doughnut' shaped ferrite for the ribbon cable that connects the scanner control PC board to the ADF analog processor PC board |
RB2-8681-000CN |
Lower internal cable guide (I/F 5) - One of six pieces that form the pivioting cable guide from the ADF assembly to the scanner assembly - Mounts on the left rear of the ADF assembly |
RB2-8682-000CN |
Upper internal cable guide (I/F 6) - Arm shaped ribbon cable retainer - One of six pieces that form the pivioting cable guide from the ADF assembly to the scanner assembly - Mounts on the left rear of the ADF assembly |
RB2-8693-000CN |
ADF stop holder - White plastic 'T' shaped bumper that limits travel of the ADF main assembly mechanism - Mounts in the upper left front corner of the lower feed mechanism |
RB2-9066-000CN |
Tray 1/MP tray link arm assembly - Left side link arm assembly |
RB2-9145-000CN |
Cleaning brush - Horizontal registration/transparency sensor cleaning brush - Located under the cyan toner cartridge |
RB2-9146-000CN |
ETB socket - Socket that right side of ETB fits into |
RB2-9147-000CN |
ETB socket - Socket that left side of ETB fits into |
RB2-9150-000CN |
Left side pressure gear |
RB2-9151-000CN |
Right side pressure gear |
RB2-9152-000CN |
One-way hinge for HP Color LaserJet 5500 Series |
RB2-9350-000CN |
Test print arm - External test print button/rod |
RB2-9358-020CN |
Interlock lever - Drum drive mechanical link to engage/disengage the drum drives |
RB2-9359-000CN |
Drive release plate - Mechanical link between disengaging drive assembly and all four drum drive assemblies |
RB2-9378-000CN |
Air filter on upper left side of printer |
RB2-9379-000CN |
Air filter at top rear of printer - Formatter fan air filter |
RB2-9390-000CN |
Cartridge guide - Lower left side toner cartridge guides - For yellow and cyan cartridges |
RB2-9391-000CN |
Cartridge guide - Upper left side toner cartridge guides - For black and magenta cartridges |
RB2-9392-000CN |
Cartridge guide - Lower right side toner cartridge guides - For yellow and cyan cartridges |
RB2-9393-000CN |
Cartridge guide - Upper right side toner cartridge guides - For black and magenta cartridges |
RB2-9398-000CN |
One disengaging Plate black plastic piece, printer used two (one on each side). |
RB2-9475-000CN |
Right hinge support |
RB2-9478-020CN |
Rear cassette cover - Rear cover for paper cassette |
RB2-9485-000CN |
Rear cover assembly |
RB2-9561-030CN |
Static comb cleaning brush - Located on left front of drop down ETB tray - Used to clean static discharge comb. |
RB2-9808-000CN |
Bushing/shaft retainer assembly - Black plastic |
RB2-9809-000CN |
Bushing/shaft retainer assembly (White plastic) |
RB2-9850-020CN |
Terminal contact plate - Provides for a connection between the high voltage cable assembly and the front toner cartridge contact spring |
RB2-9851-020CN |
Terminal contact plate - Provides for a connection between the high voltage cable assembly and the rear toner cartridge contact spring |
RB2-9852-000CN |
Rotary release guide - Small plastic clip that allows for manual carousel rotation (with a straightened paper clip) for removing toner cartridges without power |
RB2-9903-000CN |
Cable guide (Quartz Gray plastic) |
RB2-9904-000CN |
Airflow Guide (duct) - Black plastic insert piece which runs the width of the printer and has an air flow hole on right side |
RB2-9905-000CN |
Torsion spring for HP Color LaserJet 2500 Series |
RB2-9906-000CN |
Torsion spring for HP Color LaserJet 1500 Series |
RB2-9908-000CN |
Pressure roller (small Black hard plastic disk shaped roller) |
RB2-9909-000CN |
Pressure roller (small Black hard plastic solid roller) |
RB2-9912-000CN |
Top output bin guide - Small curved ribbed black plastic piece |
RB2-9916-000CN |
Mounting/grounding plate |
RB2-9916-020CN |
Cover - For the engaging motor (PM704) - Mounts on the upper left side of the rear frame assembly |
RB2-9924-000CN |
Sensor assembly mounting holder |
RB2-9925-000CN |
Sensor arm and flag - Activates the photosensor (Does NOT include the roller) |
RB2-9932-000CN |
RFI shield - Parallel wire form mounted over the fan |
RB2-9934-000CN |
Right spacer - Shipping lock for the Fuser Assembly |
RB2-9935-000CN |
Left spacer - Shipping lock for the Fuser Assembly |
RB2-9942-000CN |
Grounding plate - Provides grounding for the top-of-page sensor and shielding for the density sensor boards |
RB2-9950-000CN |
Pinch-roller - Small roller mounted on a shaft |
RB2-9952-000CN |
Tray 1 flag spring - Provides torsion for the tray 1 paper sensor flag |
RB2-9954-000CN |
Left paper feed guide (small Black plastic arm) |
RB2-9955-000CN |
Right paper feed guide (small Black plastic arm) |
RB2-9960-000CN |
Separation pad assembly - Includes the gray plastic frame with the rubber insert strip - For the cassette on the 250-sheet and 500-sheet input tray assemblies - Mounts in the paper cassette tray assembly Replaced by RF5-4258-020CN |
RB2-9963-000CN |
Separation pad support - Pivoting L shaped metal support frame (Does NOT include the separation pad assembly) |
RB2-9976-000CN |
Cross-member support - L shaped bracket used to help support the camera (photo) memory card interface boards |
RB2-9999-000CN |
Torsion spring for HP Color LaserJet 2820 Series |
RB3-0006-000CN |
Holder - Housing for the fusing connector assembly |
RB3-0007-000CN |
Insulating sheet (Transparent plastic) |
RB3-0009-000CN |
Static eliminator ground plate - Right angled metal piece with small teeth on top edge |
RB3-0010-030CN |
Feed plate - Center metal plate with slots that the ribs on the middle frame assembly go through |