Part |
Picture |
Description |
RC1-4352-000CN |
Right Electrostatic Transfer Belt (ETB) cap - Lower right side of Electrostatic Transfer Belt (ETB) assembly - Slides into a purple plastic piece |
RC1-4353-000CN |
Right side cartridge pressure lever - Holds cartridge against high voltage contact - Three used |
RC1-4354-000CN |
Cartridge interlock plate - Right side plate that provides motion for cartridge pressure levers |
RC1-4356-000CN |
70-tooth gear - Located at bottom of right side cartridge interlock plate |
RC1-4357-000CN |
Tension spring - |
RC1-4360-000CN |
Pressure plate - When this plate is pushed, it rotates a gear, which then moves a bar which engages the main drive assembly |
RC1-4382-000CN |
Cartridge alienation couple - Coupler that connects the alienation gears, inside the printer, to the alienation mechanisms in the cartridge atrium - Four used |
RC1-4383-000CN |
Compression spring - Provides pressure for developer release coupler |
RC1-4385-000CN |
Cartridge interlock plate - Left side plate that provides motion for cartridge pressure levers |
RC1-4386-000CN |
Left Electrostatic Transfer Belt (ETB) cap - Lower left side of Electrostatic Transfer Belt (ETB) assembly - Slides into a purple plastic piece |
RC1-4387-000CN |
Left side cartridge pressure lever - Holds cartridge against high voltage contact - Four used |
RC1-4392-000CN |
Gear - 70 tooth gear that moves the cartridge interlock plate on left side of printer |
RC1-4393-000CN |
Tension spring 1pc per order; Provides tension for bar on left side of cartridge electrical contacts - Four used |
RC1-4394-000CN |
High voltage terminal block - High voltage contact for toner cartridge - Four used |
RC1-4395-000CN |
Tension spring - Provides tension for left side cartridge lever - Four used |
RC1-4395-020CN |
Tension spring - Provides tension for left side cartridge lever - Four used |
RC1-4395-030CN |
Tension Spring for HP CD644A |
RC1-4396-000CN |
Compression spring - Contact spring for toner cartridge - Four used |
RC1-4397-000CN |
Pressure plate - When this plate is pushed, it rotates the bar on the left side of cartridges |
RC1-4423-000CN |
Tension spring - Provides tension for ETB right side lower pressure plate |
RC1-4433-000CN |
Ar filter for HP CD644A |
RC1-4439-000CN |
Multipurpose/tray 1 right link arm (if you need the left link arm RC1-4441-000CN) |
RC1-4440-000CN |
Torsion spring - Provides tension for MP Tray link arms - One used per side |
RC1-4441-000CN |
Multipurpose/tray 1 left link arm |
RC1-4585-000CN |
Bushing - Located on the side cover assembly (four needed) |
RC1-4803-000CN |
Compression spring - Provides tension for left side of delivery roller |
RC1-4846-000CN |
Cover arm - Left side |
RC1-4854-000CN |
Top cover - Large plastic piece beneath the face down paper output tray |
RC1-4854-030CN |
Top cover - Large plastic piece beneath the face down paper output tray |
RC1-4855-000CN |
Top right cover - Plastic cover over top right side of printer |
RC1-4855-020CN |
Top right cover - Plastic cover over top right side of printer |
RC1-4856-000CN |
Duplexer cover - Small recatangle shaped plastic piece on top right side of duplexer assembly |
RC1-4863-000CN |
Duplexer cover - Plastic strip across width of duplexer that attaches in front of paper output tray |
RC1-4864-000CN |
Cover arm - Right side |
RC1-4874-000CN |
Delivery roller - For 110-127 VAC delivery assembly |
RC1-4875-000CN |
Delivery roller - For 220-240 VAC delivery assembly |
RC1-5020-000CN |
Lock tab - White plastic tab on top of duplexer that locks unit in place - Two used |
RC1-5043-000CN |
Output tray - Duplexer output tray |
RC1-5043-020CN |
Output tray - Duplexer output tray |
RC1-5062-000CN |
Center paper retainer arm - Plastic piece with two pivot pins and two flat retaining fingers - Helps to prevent paper from re-entering the printer from the top paper output tray - Mounts on top of the Fuser Assembly |
RC1-5096-000CN |
Left (viewed from front) paper retainer arm - Plastic piece with two pivot pins and five flat retaining fingers - Helps to prevent paper from re-entering the printer from the top paper output tray - Mounts on top of the Fuser Assembly |
RC1-5097-000CN |
Right (viewed from front) paper retainer arm - Plastic piece with two pivot pins and five flat retaining fingers - Helps to prevent paper from re-entering the printer from the top paper output tray - Mounts on top of the Fuser Assembly |
RC1-5147-000CN |
Grounding spring - Mounts on the left inside wall of the print engine frame assembly towards the bottom (on the left cassette tray guide) |
RC1-5173-000CN |
Top cover / output tray - Has molded in U shaped tray for face-down paper output - Mounts to the top towards the rear of the printer |
RC1-5174-000CN |
Top cover front section - Flat 'C' shaped dark plastic cover which surrounds the face-down output paper tray - Mounts on the top towards the front on the printer (above the control panel) |
RC1-5175-000CN |
Lift up cover that attaches to top front cover - Allows access to top paper output tray - This is only the plastic top cover |
RC1-5176-000CN |
Top front sub-cover / support structure - C shaped Gray plastic cover which surrounds the face-down output paper tray and has a cutout for the control panel assembly - Mounts on the top towards the front on the printer |
RC1-5176-020CN |
Top front sub-cover / support structure - C shaped Gray plastic cover which surrounds the face-down output paper tray and has a cutout for the control panel assembly - Mounts on the top towards the front on the printer |
RC1-5176-050CN |
Top front sub-cover / support structure - C shaped Gray plastic cover which surrounds the face-down output paper tray and has a cutout for the control panel assembly - Mounts on the top towards the front on the printer |
RC1-5178-000CN |
Upper inside cover - Protects the control panel PC board and cable from damage - Mounts on the under side of the top front sub-cover / support structure |
RC1-5178-040CN |
Plastic support assembly that attaches under front top cover - For simplex models only |
RC1-5179-000CN |
Upper inside cover - Plastic support assembly that attaches under front top cover - Control panel mounts in this assembly - For duplex models only |
RC1-5183-000CN |
Left side cover assembly - Plastic cover with molded-in air louvers |
RC1-5184-000CN |
Bottom left cover - Small cover with molded-in hand grip - Covers the input paper cassette (tray 2) area on the printer |
RC1-5188-000CN |
Bottom right cover - Small cover with molded-in hand grip - Covers the input paper cassette (tray 2) area on the printer |
RC1-5188-020CN |
Bottom right cover - Small cover with molded-in hand grip - Covers the input paper cassette (tray 2) area on the printer |
RC1-5188-030CN |
Bottom right cover - Small cover with molded-in hand grip - Covers the input paper cassette (tray 2) area on the printer |
RC1-5200-000CN |
Dust cover - Small U shaped cover that covers the end of the paper cassette tray that protrudes out of the rear of the printer |
RC1-5227-000CN |
Rear cover - Stamped metal cover - Mounts on the upper rear of the printer |
RC1-5227-020CN |
Rear cover - Stamped metal cover - Mounts on the upper rear of the printer |
RC1-5249-000CN |
Left side cam - Small white plastic cam - Moves inside the left side of the electronic transfer belt (ETB) door rod link |
RC1-5311-000CN |
Right hinge cam - Small white plastic cam - Moves inside the right side of the electronic transfer belt (ETB) door rod link |
RC1-5346-000CN |
Front panel cover for tray 2 |
RC1-5440-000CN |
Paper pickup roller (D-shaped roller) - Picks up media from the paper input tray - Clips in the holder on the paper pickup shaft in the paper feeder assembly |
RC1-5644-000CN |
Edge cover - Base plate edge cover under Electrostatic Transfer Belt (ETB) side of printer |
RC1-5645-000CN |
Cable guide - Guide for Electrostatic Transfer Belt (ETB) fan to DC Controller cable |
RC1-5646-000CN |
Switching arm - Attaches to the switching arm guide |
RC1-5647-000CN |
Switching arm - Metal rod that provides mechanical link from outside power button to switching arm link that pushes rod to Low Voltage power supply |
RC1-5648-000CN |
Switching arm guide - Plastic support for metal rod that goes between Low Voltage power supply and switching arm pivot - Two used |
RC1-5649-000CN |
Switching arm guide - Plastic support for metal rod that goes between outside power button and switching arm |
RC1-5650-000CN |
Switching arm link - Plastic pivot for metal rods that mechanically connect outside power button to Low Voltage power supply |
RC1-5658-000CN |
Sheet metal cover - Right front inner lower cover |
RC1-5677-000CN |
Cable cover - Door cable cover for vertical cable path on right side of Electrostatic Transfer Belt (ETB) |
RC1-5692-000CN |
Door hinge - Left side door hinge for lower right access door |
RC1-5693-000CN |
Door hinge - Right side hinge for lower right access door |
RC1-5694-000CN |
Front cover - Front cover of printer |
RC1-5695-000CN |
Small mounting plate for printer front cover - Attaches on lower right front |
RC1-5696-000CN |
Front cover mounting plate - Upper mounting plate for printer front cover |
RC1-5711-000CN |
Fan duct - Duct for Sub power supply fan FM2 |
RC1-5728-000CN |
Guide cover - Upper guide for test engine button rod |
RC1-5759-000CN |
Guide cover - Lower guide for test engine button rod |
RC1-5760-000CN |
Test print rod - Test engine button rod - Mechanical connection for engine test |
RC1-5766-000CN |
Cartridge guide - Left side guide for toner cartriges - Covers high voltage contacts |
RC1-5771-000CN |
Cable holder - Black plactic cover that protects Formatter to Scanner cable |
RC1-5772-000CN |
Cable holder - Holds the flat cable from the formatter to the scanner assembly |
RC1-5772-020CN |
Cable holder - Holds the flat cable from the formatter to the scanner assembly |
RC1-5773-000CN |
Cable holder - Located on center back of RFI shield |
RC1-5776-000CN |
Cover shield - RFI cover shield |
RC1-5778-000CN |
Cover shield - RFI shield for cable that runs between Formatter PCA and paper scanner on top of printer |
RC1-5779-000CN |
Cover shield - Located on upper rear of printer |
RC1-5864-000CN |
Face down center guide - |
RC1-5865-000CN |
Paper guide - Face down front paper output guide |
RC1-5866-000CN |
Paper guide - Face down rear paper output guide |
RC1-5867-000CN |
Fan duct - For fans FM2 and FM4 |
RC1-5873-000CN |
Inner rear cover - |
RC1-5877-000CN |
Inner top cover - |
RC1-5878-000CN |
Inner top rear cover - |
RC1-5880-000CN |
Upper paper delivery cover - |
RC1-5904-000CN |
Cable guide - Cover for the feed unit cable |
RC1-5926-000CN |
Lock lever - Lever that locks into plate that secures the MP Paper Pickup assembly - Two used |
RC1-5927-000CN |
Lock plate - Plate that MP Paper Pickup assembly lever locks into - Two used |
RC1-5938-000CN |
Guide pin - Front mount for guide |
RC1-5939-000CN |
Spring loaded pin - Rear spring loaded pin for separation guide |
RC1-5940-000CN |
Guide - Cover/guide that goes over Tray 2 separation roller |
RC1-5953-000CN |
Torsion spring - Provides tension for lever that secures the MP Paper Pickup assembly - Two used |
RC1-5988-000CN |
Inner front cover (black) - Front cover that protects the metal frame below the Electrostatic Transfer Belt (ETB) assembly |
RC1-6012-000CN |
Upper paper pickup assembly paper jam sensor flag |
RC1-6013-000CN |
Sensor lever - Tray 2 top of stack sensor |
RC1-6042-000CN |
2 X 500 sheet feeder left side cover |
RC1-6043-000CN |
2 X 500 sheet feeder left lower cover |
RC1-6044-000CN |
2 X 500 sheet feeder right side cover |