| Part |
Picture |
Description |
| RC1-7284-020CN |
Cam - Located between large white 133 tooth gear and the bushing on the gear cover |
| RC1-7285-000CN |
Coupling lever - Lever arm that couples the drive gear to the toner cartridge. |
| RC1-7286-000CN |
Cartridge guide - Lower right side toner cartridge guide |
| RC1-7287-000CN |
Cartridge guide - Upper right side toner cartridge guide |
| RC1-7288-000CN |
Link stopper - Stop for lever arm that couples the drive gear to the toner cartridge |
| RC1-7289-000CN |
Tag link - This is an arm extension for a mechanical movement - It allows the printer to read the toner cartridge supplies status |
| RC1-7436-000CN |
Shaft, fixing shutter |
| RC1-7443-000CN |
Bushing - Located between the 25-tooth and 35-tooth gears on the tranfer drive side plate |
| RC1-7451-000CN |
Shutter lever - Connects to laser shutter |
| RC1-7544-000CN |
Upper right cable guide - Located on top of the main drive assembly and runs vertically along the almost full length of it - Black plastic. |
| RC1-7545-000CN |
Right side cable guide - Located below upper right cable guide |
| RC1-7546-000CN |
Air duct - This duct goes from fan FM1 to under the Low Voltage power supply |
| RC1-7547-000CN |
Fan duct - Diverts air from Fan 1 near the back of printer - Duct 2 |
| RC1-7548-000CN |
Fan duct - Diverts air from Fan 1 to front of printer and helps cool the Low Voltage Power Supply (LVPS) - Duct 3 |
| RC1-7550-000CN |
Rear upper cover - Small upper cover that the internal sheet metal rear cover attaches to |
| RC1-7551-000CN |
Left rear bracket - This is the sheet metal box that supports the Low Voltage Power Supply so the top cover fits |
| RC1-7552-000CN |
Tension spring - Provides tension for right and left paper guides directly under the control panel - Two used |
| RC1-7554-000CN |
Left latch - Left side paper guide/latch directly under control panel |
| RC1-7554-010CN |
Left latch - Left side paper guide/latch directly under control panel |
| RC1-7555-000CN |
Right latch - Right side paper guide/latch directly under control panel |
| RC1-7576-000CN |
Drive plate cross member - Cross member plate that attaches to duplexer separation drive assembly on right side of printer |
| RC1-7577-000CN |
Small rear cover - Small metal cover that attaches with one screw to large metal rear cover of printer |
| RC1-7583-000CN |
Grounding spring - Provides grounding for main cooling fan - Fan FM1 |
| RC1-7597-000CN |
Sensing lever - This device senses when the packaging material is removed from the toner cartridges |
| RC1-7598-000CN |
Tension spring - Provides tension for sensing lever on left side of printer |
| RC1-7599-000CN |
PC board shield - Driver PC board shield - Black plastic piece that covers Driver PCA |
| RC1-7618-000CN |
Lever lock - Left side upper lever lock for Black cartridge |
| rc1-7628-000cn |
Torsion spring for HP color laserjet printer |
| RC1-7959-000CN |
MP/Tray 1 block - Replaces media sensor in paper pickup assembly - Used on Color LaserJet 3000 only |
| RC1-8021-000CN |
Cartridge door stopper - Provided a predetermined position for the cartridge door when is open |
| RC1-8022-000CN |
Cartridge door stopper - Provided a predetermined position for the cartridge door when is open |
| RC1-8026-000CN |
Spring holder - Hold the compression spring located on the fuser bias |
| RC1-8027-000CN |
Front duplexer guide - Guide/support for duplexer assembly |
| RC1-8032-000CN |
Lever, fixing shutter |
| RC1-8034-000CN |
Sensor arm lock - Detects if cartridge is present sensor (SR9) Sensor ARM Lock |
| RC1-8035-000CN |
Tray holder - Right front paper cassette holder |
| RC1-8036-000CN |
Tray holder - Left front paper cassette holder |
| RC1-8038-000CN |
Cam, pad return, lower |
| RC1-8039-000CN |
Front pressure release lock |
| RC1-8048-000CN |
Rear guide for the duplexer assembly |
| RC1-8052-000CN |
Grounding spring - Located on the rear guide assembly |
| RC1-8069-000CN |
Plate, scanner duct |
| RC1-8075-000CN |
Lever, drive release |
| RC1-8078-000CN |
Torsion spring - Located on the fuser sensor link |
| RC1-8137-000CN |
Tray - Goes between the face down delivery cover and the top cover |
| RC1-8164-000CN |
Rear gear cover - Protects the rear part of the gear plate |
| RC1-8220-000CN |
Front cover - Face down paper delivery cover |
| RC1-8221-010CN |
Front Cover - Plastic cover on top of the paper cassette tray |
| RC1-8222-000CN |
Rear Cover - Covers the back part of the printer - Located next to the formatter cover |
| RC1-8223-000CN |
Formatter board cover - Located on the back right side of the printer next to the rear cover |
| RC1-8225-000CN |
Left rear cover - Rectangle shaped plastic cover located on the left rear side of the printer |
| RC1-8226-000CN |
Right rear cover - Plastic cover located on the right rear side of the printer next to the right door assembly |
| RC1-8227-000CN |
Left upper cover - Small rectangular cover - Located on top of the left lower cover |
| RC1-8228-000CN |
Left lower cover assembly |
| RC1-8231-000CN |
Face down side cover - Located between the front cover and the inner front cover |
| RC1-8233-000CN |
Top cover - Attached to the face down top cover |
| RC1-8235-000CN |
Duplexer blank cover - Located next to the left upper cover |
| RC1-8236-000CN |
Right grip cover - Rectangle shaped cover with two handles to pull the right door |
| RC1-8328-000CN |
Duct, scanner, lower |
| RC1-8329-000CN |
Shutter cam - Located on the lower scanner duct |
| RC1-8330-000CN |
Pushing lever - Located on the lower scanner duct |
| RC1-8331-000CN |
Slide spacer - Located between the pushing lever and the slide cam on the lower scanner duct |
| RC1-8332-000CN |
Slide cam - Located on the lower scanner duct |
| RC1-8333-000CN |
Spacer ring - Located on the lower scanner duct |
| RC1-8334-000CN |
Torsion spring - Located on the shutter cam - Provides torsion to the slide cam |
| RC1-8335-000CN |
Torsion spring - Located on the lower scanner duct |
| RC1-8358-000CN |
E-ring type for HP LaserJet Mxxxx mfp |
| RC1-8511-000CN |
Retainer (C Type) for Color LaserJet CP6015n. |
| RC1-8519-000CN |
Torque limiter - Located next to paper pick-up retard roller in multi-purpose/tray 1 assembly |
| RC1-8526-000CN |
Guide Multi-Purpose Up Guide Multi-Purpose Upper |
| RC1-8526-020CN |
Guide multi-purpose up guide multi-purpose upper |
| RC1-8527-000CN |
Multi-purpose/tray 1 blanking cover |
| RC1-8567-000CN |
Multi-purpose paper pick-up roller |
| RC1-8734-000CN |
Bushing - Located on the registration second transfer assembly |
| RC1-8925-000CN |
Damper gear - Mounts next to the fuser one way gear assembly |
| RC1-8928-000CN |
Paper sensing lever - Senses paper in intermediate transfer belt (ITB) duct assembly |
| RC1-8931-000CN |
Rail - fixing - front, front fuser rail. |
| RC1-8939-000CN |
Rail, fixing, rear |
| RC1-8959-000CN |
Guide, face-down inner |
| RC1-8961-000CN |
Air duct - Deflects air from fan FM7 |
| RC1-8964-000CN |
Face down joint duct - Located behind the fuser assembly |
| RC1-9014-000CN |
Right door cover support - Used for simplex model only |
| RC1-9043-000CN |
Band, door for HP HP Color LaserJet CP6015 Printer |
| RC1-9185-000CN |
Intermediate transfer belt (ITB) front entrance guide |
| RC1-9186-000CN |
Intermediate transfer belt (ITB) rear entrance guide |
| RC1-9189-000CN |
Arm, 1st estrangement |
| RC1-9190-000CN |
Plate, fan fixing, front |
| RC1-9201-000CN |
Paper tray cassette back end cover - Protects the back end of the cassette tray rail |
| RC1-9206-000CN |
Rear reverse scanner rail |
| RC1-9208-000CN |
Chassis rubber foot |
| RC1-9211-000CN |
Cover, main switch |
| RC1-9220-000CN |
Lever, door interlock shutter |
| RC1-9231-000CN |
Roller rail - Attaches to the left cassette rail |
| RC1-9232-000CN |
Sheet, fixing crossmember |
| RC1-9233-000CN |
Spring, leaf for HP HP Color LaserJet CP6015 Printer |
| RC1-9235-000CN |
Plate, drawer guard |
| RC1-9238-000CN |
Plate, control panel grounding |
| RC1-9244-000CN |
Torsion spring - Provides torsion to the front fuser fan plate |
| RC1-9246-000CN |
Front sensor plate - For sensor (SR32) |
| RC1-9256-000CN |
Screw tray - Attaches next ot the cable guide E |
| RC1-9260-000CN |
Holder, scanner thermistor |
| RC1-9261-000CN |
Formatter cable clamp - Holds formatter cable in a determine position |
| RC1-9276-000CN |
Cartridge duct - Plastic duct that vents air from the fan (FM3) to the cartridge area |
| RC1-9277-000CN |
Cartridge fan holder - Holds fan (FM3) |
| RC1-9278-000CN |
Fuser fan holder - Holds fan (FM2) |
| RC1-9279-000CN |
Scanner fan holder - Holds fan (FM1) |
| RC1-9300-000CN |
Button, main switch |
| RC1-9306-000CN |
Cable guide ´A´ |
| RC1-9307-000CN |
Cable guide ´B´ |
| RC1-9308-000CN |
Cable guide ´C´ |
| RC1-9309-000CN |
Scanner fan duct - Directs air into scanner area |
