| Part |
Picture |
Description |
| VD7-3221-002CN |
Fuse - 10 Amp, 125VAC max |
| VD7-3503-151CN |
Fuse - 3.15A, 250V max |
| VD7-9825-000CN |
Fuse - 5A, 250 VAC - Mounts in the flatbed scanner power supply assembly |
| VS1-0440-006CN |
Jumper - On DC controller - For signal to chassis ground |
| VS1-5057-002CN |
Fuser electrical connector |
| VS1-6173-006CN |
Frame ground connector - Frame ground cable plugs into this connector |
| VS1-6174-006CN |
Feed drive assembly connector |
| VS1-6175-006CN |
6-pin connector and housing assembly |
| VS1-6176-006CN |
250/500 sheet feeder connector |
| VS1-7177-002CN |
Fuser electrical connector |
| VS1-7177-003CN |
Retaining clip - This is a retaining clip for fuser thermistor power cable |
| VS1-7207-007CN |
Snap tight connector |
| VS1-7257-007CN |
Drawer connector - Connector located on top of tray assembly frame (right side) which connects tray assemblies to each other |
| VS1-7257-012CN |
Drawer Connector (J1903) - For the 1 x 500-sheet input tray |
| VS1-7258-007CN |
Drawer connector - Connector located on bottom of tray assembly frame on right side, which connects tray assemblies to each other |
| VS1-7333-006CN |
Duplexer connector - Connector on power supply assembly for duplexer |
| VS1-7334-006CN |
Connector (6-point) |
| VS1-7500-006CN |
Connector, Drawer, 6p |
| VS1-7500-008CN |
Connector (8-pin) |
| VS1-7514-006CN |
Duplexer connector - Connector on power supply assembly for duplexer |
| VS1-7514-008CN |
8-pin paper pick-up connector |
| VS1-7736-006CN |
Frame ground connector - Frame ground cable plugs into this connector |
| VT2-0012-005CN |
PC Board support - Plastic standoff for supporting a PC board |
| VT2-0012-006CN |
Support pcb for HP LaserJet 2430 Printer |
| WC1-0110-000CN |
On/off switch - 240V |
| WC2-5332-000CN |
Cassette size detect switch |
| WC2-5512-000CN |
Door open detection switch (SW103) |
| WC2-5637-000CN |
Push switch - Right cartridge door open switch (SW6) |
| WC2-5680-000CN |
Switch,Cassette Size Detect |
| WC2-5806-000CN |
Button switch (SW21) - For the 550-sheet paper tray feeder |
| WC4-5136-000CN |
Black toner cartridge switch - Detects when black cartridge is in correct position |
| WC4-5139-000CN |
Top cover interlock access switch |
| WC4-5171-000CN |
Black toner cartridge switch - Detects when black cartridge is in correct position |
| WC4-5175-000CN |
Micro-switch - Detects when the paper feeder/scanner assembly is open - Mounts in a support bracket on the rear frame of the ADF paper pickup assembly |
| WD1-0222-000CN |
Fuse - 3.15A, 250V max |
| WD1-0224-000CN |
Fuse - 6.3A, 125V max |
| WD1-0268-000CN |
Fuse - 15A, 250V max |
| WD1-0288-000CN |
Fuse - 10A, 125V max |
| WD3-0024-000CN |
On/off switch - 120V |
| WG8-0291-000CN |
Photo sensor - Includes (one photo sensor) photo sensors PS 1,3,5 and 6 |
| WG8-0323-000CN |
Photo sensor for HP LaserJet IIIP |
| WG8-5038-020CN |
Photo sensor for HP LaserJet IIISi |
| WG8-5210-000CN |
Photo sensor for HP Color LaserJet 8550 |
| WG8-5362-000CN |
Photo-sensor (TLP1241) - Sensor flag activated. |
| WG8-5364-000CN |
Flag activated photosensor |
| WG8-5375-000CN |
Paper sensor for HP LaserJet 5100 Series |
| WG8-5382-000CN |
Sensor PC board - Small board with flag activated photosensor |
| WG8-5593-000CN |
Sensor PC board - Small board with flag activated photosensor |
| WG8-5624-000CN |
Replacement for part WG8-5362-000CN ORDER WG8-5624-000CN PHOTO-INTERRUPTER TLP1241 Photo-sensor (TLP1241) - Sensor flag activated |
| WG8-5645-000CN |
Flag activated photo-sensor |
| WG8-5696-000CN |
Photo-interrupter sensor assembly (Does not include the sensor flag) |
| WG8-5836-000CN |
PHOTOINTERRUPTER Stapler Stacker |
| WG8-5849-000CN |
Duplex re-pick sensor - Detects the leading edge of the page |
| WG8-5935-000CN |
Fuser Output sensor (SR5) |
| WP2-5316-000CN |
Humidity Sensor |
| WP2-5368-000CN |
Humidity sensor assembly - Used to measure humidity on the device |
| WS1-6204-000CN |
Replacement for part(s).Power connector - Supplies power to optional paper trays |
| WS1-6336-000CN |
Connector assembly - For optional bottom paper tray |
| WS6-5092-000CN |
Power connector - Supplies power to optional paper trays |
| WS9-0104-000CN |
Centronics interface connector dust cap |
| WS9-0255-000CN |
Hex head bolt - Thumbscrew on left rear corner - Two used |
| WT2-0276-000CN |
Wire clamp - Holds wire/cable in place |
| WT2-0307-000CN |
Cable tie-wrap for HP LaserJet 3200 Series |
| WT2-0317-000CN |
Cable guide - For the control panel cable |
| WT2-0367-000CN |
Cable clamp - Holds cable in place |
| WT2-5041-000CN |
Cable tie wrap for HP LaserJet 1100 Series |
| WT2-5056-000CN |
Cable clip - C shaped White plastic |
| WT2-5178-000CN |
Cable guide - For the control panel cable |
| WT2-5498-000CN |
Frame cable guide |
| WT2-5678-000CN |
Cable clip - White plastic push-in clip with mounting pin |
| WT2-5694-000CN |
Snap-in cable clamp |
| WT2-5812-000CN |
Cable clip - `C` shaped white plastic clip |
| XA9-0135-000CN |
Push nut retainer |
| XA9-0265-000CN |
Screw with captured washer - To hole plastic to metal - M4X6 |
| XA9-0267-000CN |
M3 screw - 6mm long |
| XA9-0342-000CN |
Screw Stepped 3 |
| XA9-0494-000CN |
Screw - For installing lower cassette base assembly |
| XA9-0499-000CN |
Screw with captured washer - Used to fasten plastic to metal - M4 X 6mm screw |
| XA9-0596-000CN |
M3 X 6 screw for HP LaserJet 9040 9050 Series |
| XA9-0606-000CN |
Screw for LaserJet 2100 Series, LaserJet 4100 Series |
| XA9-0668-000CN |
Machine screw with captured washer - M3 X 29.5mm long |
| XA9-0828-000CN |
M3 pan head phillips screw with captive star washer - 4mm long |
| XA9-0912-000CN |
Machine screw with captured washer - M5 X 12 - Typically used to secure plastic parts to metal |
| XA9-0917-000CN |
Feed module screw - M3 x 16mm |
| XA9-0994-000CN |
Screw - M4 x 6mm long |
| XA9-1160-000CN |
Screw Tp M3x8 |
| XA9-1189-000CN |
Machine screw with attached washer - M3, 10mm - Used to hold plastic to metal |
| XA9-1200-000CN |
M3 X 8 Screw for HP LaserJet 9040 9050 Series |
| XA9-1223-000CN |
M3 X 6 TP screw |
| XA9-1263-000CN |
M3X5 Phillips washer-head machine screw with a broad, flat washer attached to the screw head - Used to fasten sheet metal parts together |
| XA9-1273-000CN |
M4 X 12mm Indented pan head screw |
| XA9-1275-000CN |
4 Wafer head machine screw included - M3, 6mm long, No. 2 Phillips recess - Secures metal to sheet metal |
| XA9-1276-000CN |
Wafer head machine screw, clear zinc, 3M X 8mm - Secures plastic to metal |
| XA9-1292-000CN |
Screw M4x14 |
| XA9-1300-000CN |
Screw - M4 X 8mm long |
| XA9-1316-000CN |
M4X10 Phillips screw with broad flat washer head - Sheet metal thread |
| XA9-1386-000CN |
M3 X 8mm long self threading screw with captured washer |
| XA9-1418-000CN |
M3x6 TP screw for HP LaserJet 500 MFP |
| XA9-1420-000CN |
M3 pan head phillips screw with captive flat and split-lock washers - 8mm long |
| XA9-1421-000CN |
M4x14 screw for HP LaserJet 3380 Series |
| XA9-1422-000CN |
M4 X 12mm machine screw with washer |
| XA9-1447-000CN |
M12 pan-head Phillips screw with annular nails - 8mm long |
| XA9-1448-000CN |
Screw - M4 X 8mm long |
| XA9-1449-000CN |
M3 pan-head Phillips screw with machine threads - 8mm long |
| XA9-1464-000CN |
Screw - Flat head phillips drive machine screw - M3 X 6mm |
| XA9-1466-000CN |
Machine screw with captured washer - M3 X 29.5mm long |
| XA9-1469-000CN |
Machine screw with attached washer - M3, 10mm - Used to hold plastic to metal |
| XA9-1495-000CN |
4 Wafer head machine screw included - M3, 6mm long, No. 2 Phillips recess - Secures metal to sheet metal |
| XA9-1500-000CN |
M3 pan-head Phillips screw with flat washer - 8mm long |
| XA9-1501-000CN |
M3 pan-head Phillips screw - 10mm long |
| XA9-1503-000CN |
M3 truss head (Flanged) phillips screw (Black oxide finish) - 6mm long |
