| Part |
Picture |
Description |
| RB2-1988-020CN |
Right side bushing for lower delivery roller |
| RB2-1989-000CN |
Left side bushing for lower delivery roller |
| RB2-1990-000CN |
Grounding plate |
| RB2-1991-020CN |
Right latch block - Housing for right side tray latch |
| RB2-1992-020CN |
Left latch block - Housing for left side tray latch |
| RB2-1997-000CN |
Roller holder - Face down guide roller holder |
| RB2-1998-000CN |
Roller - Upper roller of face-down roller guide - 4 used |
| RB2-2020-000CN |
Tray extension - Paper length adjustment extension |
| RB2-2023-000CN |
Paper stop (Blue plastic) - Paper length adjustment stop plate |
| RB2-2037-000CN |
Tray cover - 250 sheet paper tray cover |
| RB2-2042-000CN |
Extension lock - Paper length extension lock |
| RB2-2076-000CN |
Delivery roller spring - Provides tension for lower delivery roller (four used) |
| RB2-2386-000CN |
Envelope feeder drive cover |
| RB2-2387-000CN |
Tray 1 retaining arm |
| RB2-2400-000CN |
Left duplex access panel - Covers the left duplexer mount |
| RB2-2401-000CN |
Right duplex access panel - Covers the right duplexer mount |
| RB2-2404-000CN |
Cover plate - Metal bottom plate that attaches to the engine controller PC board |
| RB2-2405-000CN |
Control panel ground plate - Metal clip that provides the ground connection for control panel |
| RB2-2412-000CN |
Release lever - Actuated by release button |
| RB2-2503-000CN |
Roller Feed for HP 09998390001 |
| RB2-2509-000CN |
Clutch cover for 2000 sheet input tray |
| RB2-2519-000CN |
Back cover - Protects back of tray assembly |
| RB2-2812-000CN |
Grounding plate - Ground plate for Fuser Assembly RFI |
| RB2-2816-000CN |
Rubber foot - Non-slip replacement rubber foot |
| RB2-2817-000CN |
Dust filter for cooling fan |
| RB2-2818-000CN |
Ribbon cable guide - Protects ribbon cable on right side |
| RB2-2825-000CN |
Belt shaft 3 for HP LaserJet 2100 Series |
| RB2-2826-000CN |
Static dissipator - Discharges static electric charge as paper moves out of transfer charge roller |
| RB2-2828-000CN |
Compression spring - Toner cartridge bias connection - Rear left side |
| RB2-2829-000CN |
Compression spring - Toner cartridge bias connection - Forward left side |
| RB2-2830-000CN |
Cartridge Guide - Right Side Toner Cartridge Guide |
| RB2-2830-020CN |
Cartridge guide - Right side toner cartridge guide |
| RB2-2831-020CN |
Cartridge guide - Left side toner cartridge guide |
| RB2-2835-000CN |
Separation Pad - MP/Tray 1 Separation Pad |
| RB2-2836-000CN |
Paper sensor lever - Mechanical device that engages photo sensor PS504 |
| RB2-2837-000CN |
Torsion spring - Provides tension for paper sensor lever |
| RB2-2838-000CN |
Separation pad holder for MP/tray 1 |
| RB2-2842-000CN |
Paper sensor lever - Flag that mounts below registration assembly and passes through middle of metal plate - Activates PS502 the top of paper sensor |
| RB2-2843-000CN |
Torsion spring - Provides a small amount of back pressure for the paper sensor flag. (Flag sold separately RB2-6264-000CN). |
| RB2-2845-000CN |
Registration roller ground connection |
| RB2-2847-000CN |
Leaf spring - Electrical ground connection |
| RB2-2849-000CN |
Face-down delivery roller - Lower rollers |
| RB2-2850-000CN |
Upper delivery roller bushing |
| RB2-2856-000CN |
Toner cartridge access door |
| RB2-2857-000CN |
Rear cover - Located on back of the printer - Tray assembly attaches to this cover |
| RB2-2857-020CN |
Rear cover - Located on back of the printer |
| RB2-2859-000CN |
Power switch button |
| RB2-2860-000CN |
Power button spring - Provides tension for power button |
| RB2-2862-000CN |
Right rear side cover - Swing away I/O cover - Has slots on back for I/O cable plug-in access |
| RB2-2866-000CN |
I/R port cover - Black D shaped piece on front right side |
| RB2-2875-000CN |
Face-up output tray pull out extender |
| RB2-2876-000CN |
'Face-up' drop-down output tray |
| RB2-2877-000CN |
Paper guide - Curved teeth at bottom of face-up output tray |
| RB2-2885-000CN |
18 tooth gear for HP LaserJet 2100 Series |
| RB2-2886-000CN |
Separation sheet - Mounts on the paper width adjustable guide assembly for the multipurpose front input tray (tray 1) |
| RB2-2891-000CN |
Pickup roller assembly - Black and white `D` shaped pickup roller with a slot in the end of the shaft |
| RB2-2892-000CN |
Guide roller (Free spinning white plastic roller) - Mounts on the paper pickup drive shaft on each side of the pickup 'D' shaped roller |
| RB2-2893-000CN |
Drive shaft - Drives pickup roller |
| RB2-2894-000CN |
Paper sensor lever - Senses paper in Tray 2 pickup assembly |
| RB2-2895-000CN |
Shaft bushing/retainer - Right side pickup roller support bushing |
| RB2-2896-000CN |
Shaft bushing/retainer - Left side pickup roller support bushing |
| RB2-2897-000CN |
Shaft bushing/retainer |
| RB2-2897-020CN |
Shaft bushing/retainer |
| RB2-2899-000CN |
Gear holder - Holds two gears that engage pickup roller |
| RB2-2900-000CN |
Pickup roller - MP/TRAY 1 pickup roller |
| RB2-2902-000CN |
Pickup roller cam - Left side |
| RB2-2903-000CN |
Pickup roller cam - Right side |
| RB2-2904-000CN |
Guide roller (free spinning white plastic roller) - Mounts on the paper pickup drive shaft on each side of the pickup 'D' shaped roller |
| RB2-2926-020CN |
Transfer roller bushing - Supports right side of transfer roller |
| RB2-2935-000CN |
Gear coupler for HP LaserJet 2100 Series |
| RB2-2936-000CN |
Coupler bushing - Supports largest drive gear coupler |
| RB2-2937-000CN |
Motor plate - Metal plate that secures coupler assembly |
| RB2-2938-000CN |
Drive arm - Engages/disengages motor to drum drive assembly |
| RB2-2939-000CN |
Drive release lever - Mechanical link between drive coupling assembly and drive arm assembly |
| RB2-2943-000CN |
Clutch pin - Holds drum drive clutch springs |
| RB2-2944-000CN |
PCA guide - Holds extended I/O PC board |
| RB2-2945-000CN |
Mount plate - Protective plate for extended I/O PCA |
| RB2-2946-000CN |
FFC guide plate - Holds white flat cable in place |
| RB2-2947-000CN |
Pin holder - Holds drum drive clutch pin |
| RB2-2948-000CN |
Spring plate - Holds clutch pin and springs in place |
| RB2-2949-000CN |
Gear washer for HP LaserJet 2100 Series |
| RB2-2950-000CN |
Spring spacer - Fits between the two drum clutch springs |
| RB2-2973-000CN |
Support bushing |
| RB2-2974-000CN |
Entrance guide - Paper input guide to fusing assembly |
| RB2-2975-000CN |
Pressure plate - Covers top of fusing roller |
| RB2-2977-000CN |
Delivery roller - Roller for upper delivery guide |
| RB2-2978-000CN |
Compression spring - Provides tension for upper delivery rollers mounted on upper delivery guide - 4 used |
| RB2-2979-000CN |
Delivery roller guide - Supports delivery roller |
| RB2-2981-030CN |
Paper sensor lever - Actuates PS503 Paper Sensor |
| RB2-2982-020CN |
Torsion spring - Provides tension for paper sensor lever |
| RB2-2985-000CN |
Roller bushing - Right side delivery roller support bushing |
| RB2-2986-000CN |
Roller bushing - Left side delivery roller support bushing |
| RB2-2990-000CN |
Grounding plate - On end of delivery roller |
| RB2-3000-000CN |
Front cover - Front cover and pull handle for paper tray |
| RB2-3001-000CN |
Paper Cassette - Bare Paper Tray Frame |
| RB2-3003-020CN |
Rear end plate of paper cassette |
| RB2-3003-040CN |
Plate end - Movable end plate at back of Tray 2 paper cassette |
| RB2-3004-000CN |
Release arm - Left side lifting plate release arm |
| RB2-3005-000CN |
Release arm - Right side lifting plate release arm |
| RB2-3007-000CN |
Separation pad - Small rectangular rubber pad on front of metal lifting plate |
| RB2-3008-000CN |
Pad-SeparationSeparation pad - Moveable pad on front of Optional 250 sheet paper tray |
| RB2-3009-000CN |
Lock Arm - Locks Rear Paper Length Adjustment Plate |
| RB2-3009-040CN |
Lock arm - Locks rear paper length adjustment plate |
| RB2-3010-000CN |
Paper sensor arm |
| RB2-3012-000CN |
Leaf spring - Provides side tension for the paper input tray |
| RB2-3013-000CN |
Pad holder - Separation pad holder on front of tray |
| RB2-3019-000CN |
Shipping stopper (bright orange plastic) - Helps to prevent damage to the paper tray by restricting the movement of the lift plate (Removed for normal use) |
| RB2-3036-000CN |
Tray 1 extender - Pull-out tray extension |
| RB2-3037-000CN |
Tray 1 extender - Flip-out paper extender |
| RB2-3040-000CN |
Gear - 26 tooth - Tray 1 pickup roller drive gear |
| RB2-3041-000CN |
Tray hinge - For the left side of the multi-purpose front input tray (tray one) |
