Part |
Picture |
Description |
RB2-5640-000CN |
Laser shutter - Cartridge shutter actuator - Piece that opens cartridge shutter as it is inserted into the printer |
RB2-5652-000CN |
Cover hinge - Half of hinge that attaches to front cover |
RB2-5653-000CN |
Restraining strap |
RB2-5654-000CN |
Front cover hinge |
RB2-5655-000CN |
Retaining clip |
RB2-5656-000CN |
Pin - Located on the front cover assembly next to the roller action latch |
RB2-5659-000CN |
Top right cover - Located on the right side portion of the top cover |
RB2-5660-000CN |
Top left cover - Face down paper output cover - Located on the left side portion of the top cover |
RB2-5661-000CN |
ON/OFF switch push rod |
RB2-5664-000CN |
Tray 1/MP Tray cable cover |
RB2-5675-000CN |
Right cover cap |
RB2-5676-000CN |
Tray 1 blanking cover |
RB2-5679-000CN |
Right side lock plate |
RB2-5682-000CN |
Lower right front corner cover for tray 2 and 3 |
RB2-5683-000CN |
Lower left front corner cover for tray 2 and 3 - Does not include power button |
RB2-5684-000CN |
Right rear cover - small cover strip on rear side of right cover assembly |
RB2-5685-000CN |
Left back cover - Narrow strip covering the left rear corner of the printer |
RB2-5687-000CN |
Lower left cover - Smaller plastic piece below left door and diverter assembly |
RB2-5689-000CN |
Lower right cover - Small plastic piece below right door assembly |
RB2-5690-000CN |
Face up paper output tray |
RB2-5697-000CN |
Right front inside corner cover |
RB2-5700-000CN |
Front cover latch - Roller latch that holds front cover |
RB2-5703-000CN |
Control panel overlay - For 220V application |
RB2-5724-020CN |
Output guide - Paper input unit output guide |
RB2-5759-000CN |
Torque limiter for HP LaserJet 9040 9050 Series |
RB2-5813-000CN |
Custom/standard media size selection switch lever - Mounts on the left side of the 500-sheet paper input tray |
RB2-5816-000CN |
Torsion spring - Provides tension for paper selector switch |
RB2-5828-000CN |
Registration guide handle |
RB2-5845-000CN |
Jam removal knob |
RB2-6007-000CN |
Left side door - Left cover that diverter assembly attaches to |
RB2-6035-000CN |
Sensor flag - Long rod with forked flag toward one end and curved flag at the other |
RB2-6036-000CN |
Sensor flag - Short rod with two flat flags and a curved end flag |
RB2-6037-000CN |
Sensor flag - Short rod with two flags on it |
RB2-6042-000CN |
Torsion spring - Provides tension for bin full flag |
RB2-6077-000CN |
Microswitch lever - Activates interlock switches from both the front and left doors |
RB2-6210-000CN |
Main top cover - Does NOT include the paper input assemblies - Front left corner has hole for Face-up/ Face-down selection switch |
RB2-6249-000CN |
Feed guide hinge |
RB2-6250-000CN |
Jam clearing rod - Helps to clear paper jams |
RB2-6251-000CN |
Jam clearing lever - Helps to clear paper jams |
RB2-6255-000CN |
Fan mount - Secures fan to chassis on left side of printer |
RB2-6262-000CN |
Compression contact spring - Provides electrical voltage contact |
RB2-6263-000CN |
Compression contact spring - Provides electrical voltage contact |
RB2-6264-000CN |
Paper sensor arm - Flag for registration photosensor,(spring sold separately RB2-2843-000CN). |
RB2-6266-000CN |
Leaf spring - Grounding spring |
RB2-6268-000CN |
Idler shaf for HP LaserJet 2200 Series |
RB2-6269-000CN |
Belt drive shaft 2 - Front of middle wide belt - Tiny drive belts attach on each end of this shaft |
RB2-6270-000CN |
Paper feed belt - Short/tiny belts in front of and on each side of middle belt of paper transfer assembly |
RB2-6271-000CN |
Contact spring - High voltage contact for transfer roller |
RB2-6272-000CN |
Paper feed belt - Wide middle belt |
RB2-6273-000CN |
Paper feed belt |
RB2-6274-000CN |
Belt shaft 3 - Tiny idler shafts at back of narrow paper belts |
RB2-6277-000CN |
Top output bin roller - Lower of the two middle set of rollers - 2 used |
RB2-6280-000CN |
Top cover assembly - Face-down output tray and toner cartridge access door |
RB2-6280-020CN |
Top cover assembly - Face-down output tray and toner cartridge access door |
RB2-6283-000CN |
I/O cover - Hinged panel located on right rear of printer that allows access to concealed I/O cable connections |
RB2-6286-000CN |
Output bin extension - Pull out extension for rear paper output bin |
RB2-6287-000CN |
Rear output tray - Drop down face up rear paper output tray |
RB2-6288-000CN |
Roller guide - Small white plastic roller in rear paper output tray - 2 used |
RB2-6289-000CN |
Spring Torsion |
RB2-6294-000CN |
Power button - Located on left side of printer |
RB2-6297-000CN |
Rubber foot - Square self-adhesive rubber foot |
RB2-6302-000CN |
Feed roller - Shaft with two rollers - Feed roller for the paper cassette |
RB2-6303-000CN |
Feed roller bushing - Left side feed roller support |
RB2-6304-000CN |
Pickup roller assembly - Rubber roller on a short shaft with slots on the end - Does NOT include the two flanking hard plastic rollers |
RB2-6310-000CN |
Paper sensor lever - Senses paper at pickup roller |
RB2-6314-000CN |
Tension spring - Provides tension for duplexer release knob |
RB2-6318-000CN |
Feed roller - Shaft with two rollers - Feeds paper from the duplexer into the registration assembly |
RB2-6321-000CN |
Torsion spring - Provides tension for gear on the paper feed roller and gear for registration assembly |
RB2-6348-000CN |
Separation pad - MP/TRAY 1 separation pad |
RB2-6349-000CN |
Separation pad for Tray 2 Pad-SeparationSeparation pad - Moveable pad on front of Optional 250 sheet paper tray |
RB2-6352-000CN |
Torsion spring - Provides tension for paper sensor lever |
RB2-6357-000CN |
Entrance guide - Paper input guide to Fuser Assembly |
RB2-6368-000CN |
Pressure roller - Applies pressure to paper as it feeds through the fusing roller |
RB2-6369-000CN |
Pressure roller - Applies pressure to paper as it feeds through the fusing roller |
RB2-6372-020CN |
Delivery roller - Feeds paper out of Fuser Assembly |
RB2-6374-000CN |
Delivery roller - For upper delivery guide |
RB2-6400-000CN |
Face-Down Delivery roller - Lower rollers - Four used |
RB2-6401-000CN |
Rear paper guide - Attaches to base of rear output bin |
RB2-6402-000CN |
Paper sensor lever - Actuates PS2301 paper sensor |
RB2-6404-000CN |
Tray 1/MP Tray extension - Flip-out extension part of tray connected to the pull-out extension of tray assembly |
RB2-6405-000CN |
Tray hinge - For the left side of the multi-purpose front input tray (Tray 1) |
RB2-6406-000CN |
Tray hinge - For the right side of the multi-purpose front input tray (Tray 1) |
RB2-6470-000CN |
Roller bushing - Left side feed roller bushing |
RB2-6474-000CN |
500-sheet separation pad - Small rectangular rubber pad on front of cassette arm - Not the one on metal lifting plate |
RB2-6491-000CN |
Left upper cover - Small piece above left door |
RB2-6494-000CN |
Flapper cam for HP LaserJet M9050 MFP |
RB2-6495-000CN |
Holder clip lock - Secures the ADF/Scanner assembly to the top of printer (four used) |
RB2-6500-000CN |
Left side control panel overlay - Overlay thet mounts next to the control panel overlay (English) |
RB2-6501-000CN |
Control panel overlay - Right side (English) |
RB2-6537-000CN |
Cover hook - Used to mount the optional tray 1 assembly to the right side of the printer - Mounts on the top corners of the assembly (two used) |
RB2-6541-000CN |
Paper guide for HP LaserJet 9040 9050 Series |
RB2-7648-040CN |
Front cover and handle asembly - Plastic cover the protects the fornt side of the 2,000-sheet paper feeder tray 4 assembly |
RB2-7649-000CN |
Right cover for the 2,000-sheet paper feeder assembly |
RB2-7650-000CN |
Right rear cover for the 2,000-sheet paper feeder assembly |
RB2-7651-000CN |
Left rear cover for the 2,000-sheet paper feeder assembly |
RB2-7652-000CN |
Top cover for the 2,000-sheet paper feeder assembly |
RB2-7662-000CN |
Jetlink connector housing and cable holder assembly |
RB2-7678-020CN |
Stationary rear caster - Mounts on the bottom frame of the 2,000-sheet paper feeder assembly (two used) |
RB2-7678-030CN |
Stationary rear caster - Mounts on the bottom frame of the 2,000-sheet paper feeder assembly (two used) |
RB2-7709-000CN |
Caster for HP LaserJet 9000 Series |
RB2-7709-020CN |
Caster for HP LaserJet M9040 MFP |
RB2-7762-020CN |
Paper size switching lever - To adjust paper size in tray (standard or custom size) |
RB2-7884-000CN |
Lower ADF delivery roller - Mounts on a short shaft at the left end of the scanner assembly (four used - two per shaft) |
RB2-7902-000CN |
Flatbed ADF scanner lens cover - Black plastic piece that clips over bottom of scanner lens |
RB2-7920-000CN |
Ground plate - Small plate with two tangs - Grounds the end of the carriage rod for the scanner optical assembly - Mounts on the right end of the scanner assembly towards the rear |
RB2-7927-000CN |
Glass mounting alignment clip - Used to properly align the copyboard glass in the scanner assembly cover frame - Mounts in the left rear corner of the frame (one used) |
RB2-7928-000CN |
Glass mounting clip - Used to retain the copyboard glass in the scanner assembly cover frame - Mounts in the left front, right front, and right rear corners of the frame (three used) |
RB2-7933-000CN |
Lower front cover - Bottom of the protrusion that makes up the control panel housing - Mounts to the front of the scanner assembly |
RB2-7934-000CN |
Upper front cover - Top of the protrusion that makes up the control panel housing - Mounts to the front of the scanner assembly |
RB2-7935-000CN |
Glass mount cover - Small plastic piece that covers the mounting hardware used to retain the copyboard glass - Mounts in the recesses on the scanner assembly upper front cover (two used) |
RB2-7939-000CN |
Tray rack arm - Strip of plastic with gear teeth molded into one side - Keeps the front and rear paper guides on the ADF input tray equidistant from the center (two used) |