| Part |
Picture |
Description |
| CH971-90713 |
MEDIA ADVANCE MOTOR - ONLY INCLUDES THE MOTOR |
| CH971-90716 |
CARRIAGE IDLER ASSEMBLY - LOCATED ON LEFT END OF THE PRINTER - INCLUDES VARIOUS PARTS AND INSTRUCTIONS DESCRIBING HOW TO REMOVE AND REPLACE THE ITEM |
| CH971-90811 |
CARRIAGE DRIVE MOTOR - FOR SCITEX PRINTERS SCITEX COLOR SPAN CARRIAGE DRIVE MOTOR UNIT. |
| CH971-90826 |
ATX POWER SUPPLY - OUTPUT VOLTAGE 12VDC - LOCATED IN THE MAIN ELECTRONICS BOX |
| CH971-90854 |
GREASE KIT - USED TO LUBRICATE GRITROLL BEARINGS, MEDIA DRIVE WORM GEAR, AND UP/DOWN THREADS OF THE MEDIA HOLD-DOWN ROLLER |
| CH971-91001 |
CLIP - CONNECTED TO THE TROLLEY AND PROVIDES ATTACHMENT POINTS FOR THE CARRIAGE DRIVE BELT ON BOTH ENDS |
| CH971-91083 |
POWER SUPPLY AND POWER PLUG ADAPTER KIT - NEEDED TO IMPLEMENT THE EXTERNAL AUXILIARY POWER SOURCE FOR IDS VACUUM |
| CH971-91227 |
U-TUBE - FOR USE WITH INK BETWEEN TWO PRINTHEADS OF A COLOR |
| CH971-91329 |
FRM IO BRD OCE CS7075 HI ROHS |
| CH971-91344 |
RESTRICTOR - FOR USE WITH ALL VACUUM/PRESSURE ASSEMBLIES |
| CH971-91425 |
MYLAR ENCODER STRIP AND FOAM TAPE - IT IS LONG ENOUGH FOR A 2.5M (98-INCH) PRINTER AND CAN BE TRIMMED DOWN FOR SMALLER PRINTERS - PART REQUIRES YOU TO REUSE THE EXISTING ALUMINUM BAR FROM THE OLD STRIP |
| CH971-91475 |
FMK COOLING_FAN SERVICE_SIDE N |
| CH971-91488 |
FRM ASSY LEFT LAMP N |
| CH971-91489 |
FRM ASSY RIGHT LAMP N |
| CH971-91490 |
Y-AXIS ALIGNMENT BAR - INCLUDES FINE-THREAD SCREWS FOR ADJUSTING THE Y-AXIS ALIGNMENT OF THE PRINTHEADS - LOCATED IN FRONT OF THE PRINTHEADS |
| CH971-91491 |
MANIFOLD ASSEMBLY - INCLUDES SIX VALVES THAT MOUNTS ON THE REAR OF THE CARRIAGE ABOVE THE TROLLEY |
| CH971-91492 |
THERMISTORS KIT - INCLUDES TWO INK AND ONE AIR TEMPERATURE THERMISTOR (THEY HAVE BEEN CALIBRATED TOGETHER AND SHOULD BE REPLACED TOGETHER) |
| CH971-91493 |
MASTER PRINTHEAD - DOES NOT INCLUDE ANY THERMISTORS - USED ON ANY LOCATION OF THE PRINTER - FOR USE WITH SCITEX FB950 AND ANY MODEL OF THE DESIGNJET H SERIES |
| CH971-91496 |
FRM TROLLEY N |
| CH971-91497 |
CARRIAGE HEADBOARD ASSEMBLY - FOR USE WITH THE DESIGNJET H-SERIES AND SCITEX FB950 PRINTER |
| CH971-91498 |
FRM IONIZER N |
| CH971-91499 |
SHORT UV INK TUBE - CONNECTS TO THE PRINTHEAD WITH A LUER FITTING AND TO THE INK TRACK TUBE WITH MULTI-COLORED LUER FITTINGS |
| CH971-91500 |
FRM STRP ENCDR 54 N |
| CH971-91501 |
FRM BLT MAIN CARR DRV 54 N |
| CH971-91502 |
CARRIAGE DRIVE ASSEMBLY WITH BRACKET - FOR USE WITH SCITEX FB950/FB950 AND DESIGNJET H SERIES |
| CH971-91504 |
INK FILTER - 1.74-INCH DIAMETER - CAN BE USED WITH ANY INK COLOR - THIS FILTER IS USED IN THE OHS AREA OF THE PRINTER - FOR USE WITH SCITEX FB950 AND DESIGNJET H-SERIES |
| CH971-91505 |
ATX POWER SUPPLY - OUTPUT VOLTAGE 12VDC - LOCATED IN THE MAIN ELECTRONICS BOX |
| CH971-91506 |
FRM SPLY UV POWER SNGL CH N |
| CH971-91507 |
UV POWER SUPPLY - FOR THE SCITEX FB500, ALSO USED IN SOME MODELS OF THE DESIGNJET H-SERIES |
| CH971-91508 |
FRM CBL UV CTRL IGUS N |
| CH971-91509 |
TOUCH-SENSITIVE COLOR LCD CONTROL PANEL - USED ON ALL DESIGNJET H-SERIES AND COLORSPAN 5400UV SERIES PRINTERS |
| CH971-91510 |
FRM PWR SPLY 24 36V DC N |
| CH971-91511 |
FRM PWR SPLY IONIZER N |
| CH971-91512 |
POWER DISTRIBUTION BOARD - ROUTES INBOUND AC TO THE VARIOUS PRINTER POWER SUPPLIES - FOR THE SCITEX FB500/FB700, AND THE DESIGNJET H-SERIES |
| CH971-91513 |
FAN ASSEMBLY - COOLS THE ELECTRONICS BOX IN THE PRINTER |
| CH971-91514 |
FRM ASSY EBOX N |
| CH971-91515 |
FRM BRD I/O N |
| CH971-91517 |
FRM CBL LCD SERIAL N |
| CH971-91518 |
FRM CBL LCD VGA N |
| CH971-91519 |
FRM CBL LCD PWR N |
| CH971-91520 |
FRM ENCL USERSD BOTTOM N |
| CH971-91521 |
FRM ENCL USERSD TOP N |
| CH971-91524 |
FRM ENCL SRVSD TOP N |
| CH971-91525 |
FRM ENCL SRVSD BOTTOM N |
| CH971-91528 |
FRM ENCL CARR CVR N |
| CH971-91529 |
FRM SERVICE STATION N |
| CH971-91530 |
DRIVE BELT - USED FOR THE SERVICE STATION WIPER MOTION |
| CH971-91531 |
SHOP VAC VACUUM - INPUT VOLTAGE 220VAC - USED FOR THE SERVICE STATION |
| CH971-91532 |
FRM ASSY WIPER N |
| CH971-91533 |
SERVICE STATION WIPER MOTOR - MOVES THE WIPER HEAD IN THE Y AXIS - FOR THE SCITEX FB500/FB700/FB950, ALSO THE DESIGNJET H-SERIES |
| CH971-91534 |
FRM SW MEDIA ADV FMXABCDHIJN |
| CH971-91535 |
FRM SW RAIL LIFT N |
| CH971-91536 |
FRM GRIT ROLL N |
| CH971-91537 |
FRM MEDIA THK SNSR N |
| CH971-91538 |
FRM ASSY PINCHROLL N |
| CH971-91539 |
FRM SET 12 PNCH RLR N |
| CH971-91540 |
FRM REPACKAGING N |
| CH971-91541 |
FRM CBL OHS CONTROL N |
| CH971-91542 |
MAIN CONTROLLER BOARD - USED FOR THE OFF-HEAD SUPPLY (OHS) - HAS SOCKETS FOR THE PROFILERS |
| CH971-91543 |
VACUUM PRESSURE ASSEMBLY |
| CH971-91544 |
INK PUMP - INCLUDES THE TUBING, FITTING, AND TORX FASTENERS FOR INSTALLATION |
| CH971-91545 |
FRM TUBE SOL PRS LNG N |
| CH971-91547 |
FRM TUBE VACUUM LONG N |
| CH971-91550 |
FRM CBL TRACK GND N |
| CH971-91551 |
FRM CBL TRACKDATA N |
| CH971-91552 |
FRM CBL TRACKPOWER N |
| CH971-91573 |
FRM ASSY INPUT TABLE N |
| CH971-91574 |
FRM ASSY OUTPUT TABLE N |
| CH971-91575 |
FRM MEDIA COLLET N |
| CH971-91576 |
DOOR SWITCH - USED ONT THE COVER-OPEN DETECT - FOR USE WITH DESIGNJET H-SERIES PRINTERS |
| CH971-91577 |
CARRIAGE DRIVE SHAFT - SHAFT IS KNURLED TO PREVENT PULLEY FROM SLIPPING ON THE SHAFT - FOR THE SCITEX FB500/FB700/FB910/FB950 PRINTER |
| CH971-91586 |
AC RELAY - LOCATED IN THE MAIN ELECTRONICS BOX |
| CH971-91587 |
FRM ENCL TOP MIDDLE N |
| CH971-91588 |
FRM BLWR PLATEN N |
| CH971-91589 |
PRINTHEAD CAP - USED TO CAP A PRINTHEAD PORT OR SIMILAR LUER FITTING LOCATION |
| CH971-91590 |
TUBE CAP - USED TO CAP THE END OF THE LUER FITTING THAT NORMALLY CONNECTS TO THE INK TUBE |
| CH971-91591 |
FRM CASTER STAND N |
| CH971-91592 |
FRM ASSY EBOX OCE ROHS N |
| CH971-91593 |
FRM TRACK CHAIN LINKS N |
| CH971-91594 |
QUARTZ LAMP GLASS - INSERTS BELOW THE LEFT OR RIGHT LAMP HOUSING - FOR THE FB500/FB700/FB950 ALSO THE DESIGNJET H-SERIES |
| CH971-91595 |
IDLER ASSEMBLY - LOCATED ON SERVICE-END OF THE RAIL - FOR USE WITH SCITEX FB910/FB950 AND THE DESIGNJET H-SERIES |
| CH971-91596 |
UV LAMP HOUSING COOLING FAN - FOR THE SCITEX FB500/FB700/FB950, AND DESIGNJET H-SERIES PRINTERS |
| CH971-91598 |
SHOPVAC VACUUM - INPUT VOLTAGE 110VAC (USA) |
| CH971-91599 |
FAN ASSEMBLY - LOCATED ON THE TOP ENCLOSURE AND END ENCLOSURES - FOR THE SCITEX FB500/FB700, ALSO THE DESIGNJET H-SERIES |
| CH971-91602 |
INK LINE AND FITTINGS KIT - INCLUDES 24-INCH UV INK TUBING AND AN ASSORTMENT OF COLOR-CODED LUER FITTINGS |
| CH971-91604 |
FRM MEDIA SPOOL N |
| CH971-91605 |
CAMERA ASSEMBLY - FOR USE WITH SCITEX FB950 AND THE DESIGNJET H-SERIES |
| CH971-91606 |
PLATEN PIRANHA UPPER |
| CH971-91607 |
FMK SHIM CARRIAGE 5400 PIN PLATE N |
| CH971-91608 |
FMK TAPE LCD PIRANHA N |
| CH971-91609 |
KIT BRG LOWER CARRIAGE |
| CH971-91610 |
FRM REPACKAGING UNIVERSAL EXCHANGE |
| CH971-91611 |
FRM PINCH ROLLER WHEEL SINGLE N |
| CH971-91612 |
FRM MTR PIRANHA RAIL N |
| CH971-91617 |
FRM IONIZER UL N |
| CH971-91618 |
IONIZER POWER SUPPLY - FOR REPLACEMENT OF THE SIMCO-BRANDED IONIZER-BAR POWER SUPPLY ONLY |
| CH971-91619 |
KIT MNT ADJ TABLE N |
| CH971-91621 |
FRM ASSY CARRIAGE N |
| CH971-91627 |
FRM ASSY OHS 2_COLOR_PUMP_PLATE N |
| CH971-91628 |
FRM ASSY OHS 3 COLOR PUMP PLATE N |
| CH971-91629 |
FMK TOOL BEARING CARRIAGE INSTALL N |
| CH971-91630 |
FRM ASSY EBOX UL N |
| CH971-91631 |
SERVICE TOOLS KIT - KIT INCLUDES THE HEAD HEIGHT GAUGE, SQUEEZE BOTTLE (FOR FLUSH), LINT-FREE CLOTHS, LUER CAPS, AND THE CARRIAGE BELT - FOR USE WITH SCITEX FB950 AND THE DESIGNJET H-SERIES |
| CH971-91632 |
FRM LIFT MTR SRV STN N |
| CH971-91634 |
OFF-HEAD SUPPLY (OHS) INK COUPLER - INCLUDES ONE COUPLING AND THE NUT USED TO SECURE IT ON THE PRINTER - THIS IS THE QUICK-DISCONNECT ATTACHMENT FOR THE INK BOXES AND RECEIVES THE CONNECTOR FROM THE INKBOX PIGTAIL |
| CH971-91639 |
TUBE/FILTER/FITTING ASSEMBLY - USED BETWEEN THE PRINTHEAD AND THE AIR MANIFOLD |
| CH971-91640 |
GRIT ROLL BEARINGS KIT - INCLUDES 12 UNITS |
| CH971-91642 |
FRM EDGE HOLD DOWN N |
| CH971-91643 |
FRM ASSY INPUT+OUTPUT TABLES N |
| CH971-91644 |
REPLACEMENT FILTER - INCLUDES MEDIA AND MESH USED INSIDE THE SHOPVAC, AS WELL AS RELATED FASTENERS - FOR THE SCITEX FB500/FB700 PRINTERS |
| CH971-91647 |
FRM SET CASTER STAND N |
