| Part |
Picture |
Description |
| C6090-60012 |
MAIN LOGIC PC BOARD FOR HEWLETT PACKARD DESIGNJET PLOTTERS. |
| C6090-60027 |
BOOT ROM DIMM - RTL VERSION A.01.01 |
| C6090-60028 |
HEWLETT PACKARD POWER SUPPLY UNIT FOR DESIGNJET PRINTERS 5000 AND 5500 SERIES. |
| C6090-60029 |
COOLING FAN - INSTALLED UNDER POWER SUPPLY (TWO USED) PART NUMBER IS FOR ONE PC. |
| C6090-60032 |
ELECTRONICS MODULE COVER KIT - INCLUDES MAIN COVER, EIO COVER AND HARD DISK COVER(ORDER Q1251-60110) |
| C6090-60033 |
ELECTRONICS MODULE CHASSIS - DOES NOT INCLUDES THE ELECTRONICS MODULE METAL CHASSIS BASE (USE YOUR EXISTING CASING). PART INCLUDES; POWER SUPPLY PC BOARD Q1251-60123 AND COOLING FANS Q1251-60312 ONLY. DOES NOT INCLUDE MAIN LOGIC PCA |
| C6090-60034 |
42-INCH ROLLFEED SPINDLE ROD ASSEMBLY - INCLUDES SPINDLE, HUBS, AND END CAPS |
| C6090-60037 |
BACK COVER - THE LARGE PLASTIC COVER WITH HINGES FOR THE TOP COVER - 42 INCHES |
| C6090-60038 |
RIGHT END COVER - INCLUDES CONTROL PANEL CABLE AND AEROSOL FAN |
| C6090-60039 |
LEFT END COVER AND REAR DOOR |
| C6090-60040 |
REAR DOOR - INSTALLED ON LEFT END COVER |
| C6090-60041 |
INK SUPPLY STATION (ISS) PC BOARD - INCLUDES CABLE |
| C6090-60042 |
LEFT TRIM - BETWEEN THE MAIN CHASSIS AND THE LEFT END COVER |
| C6090-60043 |
RIGHT TRIM - BETWEEN THE MAIN CHASSIS AND THE RIGHT END COVER - INCLUDES WINDOW SENSOR AND LEVER SENSOR |
| C6090-60044 |
RIGHT REAR COVER |
| C6090-60045 |
LEFT REAR COVER |
| C6090-60046 |
HARDWARE KIT FOR PRINTER STAND - INCLUDES SCREWDRIVER AND SCREWS |
| C6090-60047 |
LEG ASSEMBLY - DOES NOT INCLUDE THE FOOT ASSEMBLY |
| C6090-60049 |
FOOT ASSEMBLY (INCLUDES CASTERS) - MOUNTS TO THE BOTTOM OF THE PRINTER STAND LEGS (TWO USED) |
| C6090-60055 |
TOP CROSS-BRACE - BRACE THAT CONNECTS AND SUPPORTS THE TWO STAND LEGS - 42 INCHES |
| C6090-60056 |
BOTTOM CROSS-BRACE - BRACE THAT CONNECTS AND SUPPORTS THE TWO STAND LEGS - 42 INCHES |
| C6090-60058 |
HEWLETT PACKARD (HP) - DYE BASE INK TUBES ASSEMBLY 42 INCHES. INK TUBES ASSEMBLY - INCLUDES 6 INK TUBES COMPLETE WITH HARDWARE ASSEMBLIES AT BOTH ENDS (CARRIAGE CRANE AND INK SUPPLY STATION CRANE), 6 SETUP PENS, INK LEAK DETECTOR SYSTEM, CARRIER CLIP & ISS. (FOR UV ORDER Q1251-60265). |
| C6090-60059 |
ENCODER STRIP - 42-INCHES CONNECTS FROM LEFT TO RIGHT SIDE OF PLOTTER. |
| C6090-60060 |
TRAILING CABLE KIT - INCLUDES TRAILING CABLE, TRAILING CABLE CLIP, COVER CAP, TRAILING FERRITE, AND SCREWS - 42 INCHES 3CABLES. |
| C6090-60072 |
CARRIAGE BELT - LONG BELT ATTACHED TO THE CARRIAGE (FOR THE 42-INCH WIDE VERSION PLOTTER) |
| C6090-60073 |
PINCH ASSEMBLY KIT - INCLUDES ALL REQUIRED PINCH WHEELS, PINCHWHEEL MOUNTS AND SPRINGS - 42 INCHES |
| C6090-60074 |
42-INCH ROLLFEED SPINDLE ROD ASSEMBLY - INCLUDES SPINDLE, HUBS, AND END CAPS |
| C6090-60075 |
CENTER PAPER GUIDE (FOR THE 42-INCH WIDE VERSION PLOTTER) |
| C6090-60076 |
PINCHARM LIFT (CAM LEVER SHAFT) MECHANISM - INCLUDES CAM (A LONG BAR), CAM LEVER ARM, CAM LINKAGE ROD AND SCREWS - 42-INCHES |
| C6090-60077 |
ENTRY ROLLER - THE LONG ROLLER LOCATED UNDER THE MAIN PRINTER CHASSIS - 42 INCHES |
| C6090-60078 |
REAR TUBE GUIDE ASSEMBLY - INCLUDES SAFETY ARM FOR TOP COVER - 42 INCHES |
| C6090-60079 |
FRONT PLATEN KIT - INSTALLED BELOW THE MEDIA DEFLECTORS AND IN FRONT OF THE CENTER PLATEN - INCLUDES SCREWS (42-INCHES) |
| C6090-60081 |
MAINTENANCE KIT - INCLUDES SCREWS, LABEL, FERRITE, TRAILING CLIP, DETECT ASSEMBLY, ENCODER HOLDER, TOOL ASSEMBLY, FOAM, TRAILING CABLE ASSEMBY, STRIP ENCODER, PULLEY ASSEMBLY, TENSIONER ASSEMBY, 42-INCH AND 60-INCH CARRIAGE BELTS AND CARRIAGE COVER |
| C6090-60083 |
SERVICE STATION ASSEMBLY - INCLUDES MOTORS, SPITTOON FOAM, DROP DETECTOR, AND PRIMER ASSEMBLY |
| C6090-60084 |
AIR PRESSURIZATION SYSTEM (APS) - INCLUDES PUMP, VALVE, PRESSURE SENSOR, AND APS HOUSING |
| C6090-60085 |
INK SUPPLY STATION (ISS) - INCLUDES GROUNDING STRIP |
| C6090-60087 |
INK LEAK DETECTOR ASSEMBLY - INCLUDES SENSOR, INK COLLECTOR, LEAK SENSE CABLE AND LEAK SENSE CABLE CLIP |
| C6090-60088 |
BELT TENSIONER KIT - KEEPS CARRIAGE BELT TIGHT - INCLUDES PULLEY ASSEMBLY, PULLEY SPRING, WEDGE, AND ACTUATOR ARM |
| C6090-60092 |
CARRIAGE (SCAN-AXIS) MOTOR ASSEMBLY - INCLUDES PULLEY AND POWER CABLE |
| C6090-60093 |
BOOSTER FAN ASSEMBLY |
| C6090-60094 |
CUTTER ASSEMBLY KIT - INCLUDES CUTTER, SCREW AND WASHER |
| C6090-60095 |
VACUUM FAN ASSEMBLY - INCLUDES THE FAN AND AIR FLOW GUIDE ASSEMBLY |
| C6090-60096 |
DRIVE ROLLER GEAR (OVERDRIVE GEAR) |
| C6090-60097 |
LEVER SUPPORT BRACKET |
| C6090-60102 |
LEVER - USED TO ACTUATE THE PINCH ARM LIFT MECHANISM |
| C6090-60103 |
MEDIA SENSOR FOR HP DESIGNJET 5000 SERIES |
| C6090-60104 |
MEDIA DEFLECTOR KIT - INSTALLED IN FRONT OF PINCH WHEELS - KIT INCLUDES FOUR DEFLECTORS |
| C6090-60105 |
SPINDLE HUB (BLUE) - INSTALLED ON THE LEFT END OF THE ROLLFEED SPINDLE. FOR THE RIGHT SIDE /BLACK HUB SEE (C6095-40092). |
| C6090-60106 |
SETUP PRINTHEAD KIT - USED TO PRIME THE INK TUBES - INCLUDES 6 SETUP PRINTHEADS |
| C6090-60107 |
BRACKET KIT FOR THE ELECTRONICS MODULE |
| C6090-60109 |
CABLE PROTECTOR (RETAINER) KIT - PACKAGE OF SEVEN PLASTIC CABLE EDGE PROTECTORS |
| C6090-60110 |
TUBE GUIDE DOOR AND SPRING |
| C6090-60111 |
CONTROL PANEL ASSEMBLY - INCLUDES CONTROL PANEL CONTROL PANEL ASSEMBLY - INCLUDES CONTROL PANEL CABLE (COMES WITH 3 BUTTONS). |
| C6090-60112 |
ADAPTER FOR 3-INCH PAPER ROLL (PACKAGE OF 2 ADAPTERS) |
| C6090-60175 |
TAKE-UP REEL PAPER GUIDE - HAS A LEVER USED TO LOCK THE GUIDE ON THE SPINDLE |
| C6090-60177 |
TAKE-UP REEL CORE - 42 INCHES |
| C6090-60178 |
42-INCH TAKE-UP REEL SPINDLE |
| C6090-60179 |
TAKE-UP REEL PAPER DEFLECTOR ASSEMBLY - A LONG TUBE ATTACHED TO THE PRINTER WITH BRACKETS - INCLUDES DEFLECTOR TUBE, LEFT AND RIGHT DEFLECTOR BRACKETS, AND DEFLECTOR LOCK ASSEMBLIES INSERTED INTO EACH END OF THE TUBE - 42 INCHES |
| C6090-60180 |
SHIELD KIT (EMC COVERS) - ELECTROMAGNETIC SHIELDS INSTALLED BEHIND AND BELOW THE ELECTRONICS MODULE BASE - 42 INCHES |
| C6090-60181 |
FRONT TUBE GUIDE ASSEMBLY - INCLUDES TUBE GUIDE DOOR AND SPRING - 42 INCHES |
| C6090-60182 |
RIGHT TAKE-UP REEL HOLDER |
| C6090-60183 |
LEFT TAKE-UP REEL HOLDER |
| C6090-60184 |
TAKE-UP REEL SENSOR |
| C6090-60185 |
128MB SDRAM DIMM MEMORY MODULE |
| C6090-60187 |
64MB SDRAM DIMM MEMORY MODULE |
| C6090-60190 |
SHIELD KIT (EMC COVERS) - ELECTROMAGNETIC SHIELDS INSTALLED BEHIND AND BELOW THE ELECTRONICS MODULE BASE - FOR 60-INCH MODELS |
| C6090-60199 |
PAPER MOTOR SERV |
| C6090-60210 |
MANUAL/SOFTWARE FOR DESIGNJET 5000 SERIES |
| C6090-60231 |
UV INK TUBES ASSEMBLY - INCLUDES 6 INK TUBES COMPLETE WITH HARDWARE ASSEMBLIES AT BOTH ENDS (CARRIAGE CRANE AND INK SUPPLY STATION CRANE) , 6 SETUP PENS, INK LEAK DETECTOR SYSTEM COMPONENTS, CARRIER CLIP, ISS HOUSING FOAM - 60 INCHES |
| C6090-60232 |
UV INK TUBES ASSEMBLY - INCLUDES SIX INK TUBES COMPLETE WITH HARDWARE ASSEMBLIES AT BOTH ENDS (CARRIAGE CRANE AND INK SUPPLY STATION CRANE), SIX SETUP PENS, INK LEAK DETECTOR SYSTEM COMPONENTS, CARRIER CLIP, ISS HOUSING FOAM. (FOR DYE BASE ORDER Q1251-60254). |
| C6090-60235 |
PRINTHEAD STORAGE CONTAINER |
| C6090-60236 |
PRINTHEAD CARRIAGE ASSEMBLY - INCLUDES CARRIAGE, CARRIAGE HEIGHT TOOL, CUTTER ASSEMBLY, CARRIAGE POSITION SENSOR AND LINE SENSOR |
| C6090-60247 |
HARD DRIVE (VERSION A.02.18) - FOR HP DESIGNJET PLOTTERS. (FOR POSTSCRIPT HARD DRIVE ORDER C6091-69268). |
| C6090-60263 |
MEDIA GUIDE FOAM KIT - SMALL BLACK FOAM PIECES THAT FIT IN DESIGNATED SPACES LOCATED ON THE PLATEN |
| C6090-60267 |
ENCODER STRIP - 42-INCHES CONNECTS FROM LEFT TO RIGHT SIDE OF PLOTTER. |
| C6090-60271 |
FRONT TUBE GUIDE ASSEMBLY (FOR THE 42-INCH WIDE VERSION PLOTTER) - INCLUDES TUBE GUIDE DOOR AND SPRING |
| C6090-60272 |
TUBE GUIDE DOOR AND SPRING |
| C6090-60281 |
PRINTHEAD CARRIAGE ASSEMBLY - INCLUDES CARRIAGE, CARRIAGE HEIGHT TOOL, CUTTER ASSEMBLY, CARRIAGE POSITION SENSOR AND LINE SENSOR |
| C6090-60291 |
TOP COVER ASSEMBLY - COVERS THE TOP OF THE PRINTER |
| C6090-60309 |
TAKE-UP REEL PAPER GUIDE - HAS A LEVER USED TO LOCK THE GUIDE ON THE SPINDLE |
| C6090-60310 |
42-INCH TAKE-UP REEL SPINDLE |
| C6090-60311 |
CENTER PLATEN ASSEMBLY |
| C6090-60314 |
MAINTENANCE KIT - INCLUDES LENS MAINTENANCE KIT, CARRIAGE INTERCONNECT WIPER KIT, ROLLER LUBRIFICATION KIT, AND PLATEN CLEANING INSTRUCTIONS |
| C6090-60316 |
ELECTRONICS MODULE CHASSIS - DOES NOT INCLUDES THE ELECTRONICS MODULE METAL CHASSIS BASE (USE YOUR EXISTING CASING). PART INCLUDES; POWER SUPPLY PC BOARD Q1251-60123 AND COOLING FANS Q1251-60312 ONLY. DOES NOT INCLUDE MAIN LOGIC PCA |
| C6090-60317 |
MAIN LOGIC PC BOARD - INCLUDES IDS (INK DELIVERY SYSTEM) BOARD CABLE |
| C6090-60318 |
PCI TO IDE BRIDGE PC BOARD - INCLUDES HDD DATA AND POWER CABLES |
| C6090-60324 |
HARD DRIVE (VERSION A.02.18) - FOR HP DESIGNJET PLOTTERS. (FOR POSTSCRIPT HARD DRIVE ORDER C6091-69268). |
| C6090-60327 |
BELT TENSIONER KIT - KEEPS CARRIAGE BELT TIGHT - INCLUDES PULLEY ASSEMBLY, PULLEY SPRING, WEDGE, AND ACTUATOR ARM |
| C6090-60328 |
CARRIAGE (SCAN-AXIS) MOTOR ASSEMBLY - INCLUDES PULLEY AND POWER CABLE |
| C6090-60344 |
HARD DRIVE (VERSION A.02.18) - FOR HP DESIGNJET PLOTTERS. (FOR POSTSCRIPT HARD DRIVE ORDER C6091-69268). |
| C6090-60347 |
RIGHT TAKE-UP REEL HOLDER |
| C6090-60348 |
LEFT TAKE-UP REEL HOLDER |
| C6090-60349 |
TAKE-UP REEL SENSOR |
| C6090-69028 |
HEWLETT PACKARD POWER SUPPLY UNIT FOR DESIGNJET PRINTERS 5000 ONLY. |
| C6090-69236 |
PRINTHEAD CARRIAGE ASSEMBLY - INCLUDES CARRIAGE, CARRIAGE HEIGHT TOOL, CUTTER ASSEMBLY, CARRIAGE POSITION SENSOR AND LINE SENSOR |
| C6090-69247 |
HARD DRIVE (VERSION A.02.18) - FOR HP DESIGNJET PLOTTERS. (FOR POSTSCRIPT HARD DRIVE ORDER C6091-69268). |
| C6090-69281 |
PRINTHEAD CARRIAGE ASSEMBLY - INCLUDES CARRIAGE, CARRIAGE HEIGHT TOOL, CUTTER ASSEMBLY, CARRIAGE POSITION SENSOR AND LINE SENSOR. |
| C6090-69317 |
MAIN LOGIC PC BOARD FOR HEWLETT PACKARD DESIGNJET PLOTTERS. |
| C6090-69318 |
PCI TO IDE BRIDGE HARD DRIVE DISK (HDD) CONTROLLER SERVICE BOARDPCI TO IDE BRIDGE HARD DRIVE DISK (HDD) CONTROLLER SERVICE BOARD REPLACED: C6090-60318 |
| C6090-69344 |
HARD DRIVE (VERSION A.02.18) - FOR HP DESIGNJET PLOTTERS. (FOR POSTSCRIPT HARD DRIVE ORDER C6091-69268). |
| C6090A |
HP DESIGNJET 5000 PRINTER |
| C6090V |
HP DESIGNJET 5000 UV PRINTER |
| C6091-00139 |
NAMEPLATE - DESIGNJET 5000PS LOGO |
| C6091-60008 |
BOOT ROM DIMM - POSTSCRIPT VERSION A.01.01 |
| C6091-60247 |
HARD DRIVE (VERSION A.02.18) HD PATA - FOR HEWLETT-PACKARD DESIGNJET POSTCRIPT PLOTTERS, ONLY USE ON HP DESIGNJET 5000PS MODELS. |
| C6091-60268 |
HARD DRIVE (VERSION A.02.18) - FOR HEWLETT-PACKARD DESIGNJET POSTCRIPT PLOTTERS OR NON-POSCRIPT ASWELL. |
| C6091-69255 |
HARD DRIVE (VERSION A.02.18) HD PATA - FOR HEWLETT-PACKARD DESIGNJET POSTCRIPT PLOTTERS, ONLY USE ON HP DESIGNJET 5000PS MODELS. |
| C6091-69268 |
HARD DRIVE (VERSION A.02.18) - FOR HEWLETT-PACKARD DESIGNJET POSTCRIPT PLOTTERS, ONLY USE ON HP DESIGNJET 5000PS MODELS. |
| C6091A |
HP DESIGNJET 5000PS PRINTER |
| C6091V |
HP DESIGNJET 5000PS UV PRINTER |
| C6095-40065 |
QUICK REFERENCE GUIDE HOLDER - INSTALLED ON THE BACK OF THE RIGHT END COVER |
